lkml.org 
[lkml]   [2019]   [Jan]   [22]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH 3/4] dt-bindings: spi: Add the DMA properties for the SPI dma mode
Hi Baolin,

On Tue, Jan 22, 2019 at 3:23 AM Baolin Wang <baolin.wang@linaro.org> wrote:
> On Mon, 21 Jan 2019 at 21:53, Rob Herring <robh+dt@kernel.org> wrote:
> > On Tue, Jan 15, 2019 at 7:47 AM Baolin Wang <baolin.wang@linaro.org> wrote:
> > > From: Lanqing Liu <lanqing.liu@spreadtrum.com>
> >
> > The email address should be updated with unisoc.com.
>
> Sure.
>
> >
> > > Add the DMA properties for the SPI dma mode.
> > >
> > > Signed-off-by: Lanqing Liu <lanqing.liu@spreadtrum.com>
> > > Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
> > > ---
> > > Documentation/devicetree/bindings/spi/spi-sprd.txt | 9 +++++++++
> > > 1 file changed, 9 insertions(+)
> > >
> > > diff --git a/Documentation/devicetree/bindings/spi/spi-sprd.txt b/Documentation/devicetree/bindings/spi/spi-sprd.txt
> > > index bad211a..01ef53f 100644
> > > --- a/Documentation/devicetree/bindings/spi/spi-sprd.txt
> > > +++ b/Documentation/devicetree/bindings/spi/spi-sprd.txt
> > > @@ -14,6 +14,12 @@ Required properties:
> > > address on the SPI bus. Should be set to 1.
> > > - #size-cells: Should be set to 0.
> > >
> > > +Optional properties:
> > > +dma-names: Should contain names of the SPI used DMA channel.
> > > +dmas: Should contain DMA channels which the SPI used sorted in the
> > > + same order as the dma-names property.
> > > +sprd,dma-slave-ids: Should contain the DMA number that the SPI hardware required.
> > > +
> > > Example:
> > > spi0: spi@70a00000{
> > > compatible = "sprd,sc9860-spi";
> > > @@ -21,6 +27,9 @@ spi0: spi@70a00000{
> > > interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
> > > clock-names = "spi", "source","enable";
> > > clocks = <&clk_spi0>, <&ext_26m>, <&clk_ap_apb_gates 5>;
> > > + dma-names = "rx_chn", "tx_chn";
> > > + dmas = <&apdma 11>, <&apdma 12>;
> > > + sprd,dma-slave-ids = <11 12>;
> >
> > When would this be different values from what's in 'dmas'?
>
> Slave id is not always same with the DMA channel number in 'dmas', and
> it is just coincident for SPI driver. Moreover for different SoC , the
> slave ids for DMA engine consumers are not same. So we need one
> property to specify the slave id for the consumers to trigger DMA
> transfer.

Perhaps the DMA controller should use #dma-cells = <2>, so you can specify
the second value in the dmas property?

Gr{oetje,eeting}s,

Geert

--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@linux-m68k.org

In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
-- Linus Torvalds

\
 
 \ /
  Last update: 2019-01-22 09:12    [W:0.051 / U:1.136 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site