lkml.org 
[lkml]   [2019]   [Jan]   [2]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRE: [LINUX PATCH v12] mtd: rawnand: pl353: Add basic driver for arm pl353 smc nand interface
Date
Hi,

> -----Original Message-----
> From: Miquel Raynal [mailto:miquel.raynal@bootlin.com]
> Sent: Wednesday, January 2, 2019 2:04 PM
> To: Romain Perier <romain.perier@gmail.com>
> Cc: Naga Sureshkumar Relli <nagasure@xilinx.com>; Boris Brezillon
> <bbrezillon@kernel.org>; linux-mtd@lists.infradead.org; peterpandong@micron.com;
> linux-kernel@vger.kernel.org
> Subject: Re: [LINUX PATCH v12] mtd: rawnand: pl353: Add basic driver for arm pl353
> smc nand interface
>
> Hi Romain,
>
> Switching Boris address.
>
> Romain Perier <romain.perier@gmail.com> wrote on Fri, 21 Dec 2018
> 10:17:50 +0100:
>
> > Hello,
> >
> > I have rebased this patch onto 4.19.11. I use it on a Zynq7000-based
> > board with a NAND chip Micron MT29F4G08ABADAH4, since ~2 weeks now.
> > The only problem I have to report is that when I boot with an
> > unchanged driver on my board, I get the following logs:
> >
> > [ 1.988797] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xdc
> > [ 1.995184] nand: Micron MT29F4G08ABADAH4
> > [ 1.999187] nand: 512 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
> > [ 2.402661] nand: timeout while waiting for chip to become ready
> > [ 2.408665] nand: timing mode 5 not acknowledged by the NAND chip
> > [ 2.416251] Bad block table not found for chip 0
> > [ 2.422278] Bad block table not found for chip 0
> > [ 2.426903] Scanning device for bad blocks
> > [ 2.431024] Bad eraseblock 0 at 0x000000000000
> > [ 2.435509] Bad eraseblock 1 at 0x000000020000
> > [ 2.439978] Bad eraseblock 2 at 0x000000040000
> > [ 2.444465] Bad eraseblock 3 at 0x000000060000
> > [ 2.448936] Bad eraseblock 4 at 0x000000080000
> > [ 2.453423] Bad eraseblock 5 at 0x0000000a0000
> > [ 2.457893] Bad eraseblock 6 at 0x0000000c0000
> > [ 2.462354] Bad eraseblock 7 at 0x0000000e0000
> > [ 2.466841] Bad eraseblock 8 at 0x000000100000
> > [ 2.471304] Bad eraseblock 9 at 0x000000120000
> > [ 2.475793] Bad eraseblock 10 at 0x000000140000
> > [ 2.480349] Bad eraseblock 11 at 0x000000160000
> >
> > [...]
> >
> >
> > After investigation, it seems that during the nand_scan phase, the
> > NAND subsystem tests different timing modes on the NAND chip (mode 0
> > seems to be apply during reset, and then it tries to detect the best
> > mode supported by the NAND chip). Only the mode 0 works here, trying
> > the use the mode 5 resuls in an error (as you can see in the log) and
> > a bad BBT detection. Both modes are supported by the NAND chip. In
> > order to fix this, I had to put the nfc timing into the device node of the nfc, inside the DT
> (that's not a real fix, ihmo).
>
> Thanks for testing! Indeed, the ->setup_data_interface() callback should be fixed.
Ok, let me check.
Meanwhile, can you share the timings that you put inside the DT?
>
> > Except this, everything is working as expected. Everything is stable
> > with correct performances.
> >
> > If I can provide more informations, feel free to ask.
>
> [...]
>
> > > +static int pl353_setup_data_interface(struct mtd_info *mtd, int csline,
> > > + const struct nand_data_interface *conf) {
> > > + struct nand_chip *chip = mtd_to_nand(mtd);
> > > + struct pl353_nand_controller *xnfc =
> > > + container_of(chip, struct pl353_nand_controller, chip);
> > > + const struct nand_sdr_timings *sdr;
> > > + u32 timings[7], mckperiodps;
> > > +
> > > + if (csline == NAND_DATA_IFACE_CHECK_ONLY)
> > > + return 0;
> > > +
> > > + sdr = nand_get_sdr_timings(conf);
> > > + if (IS_ERR(sdr))
> > > + return PTR_ERR(sdr);
> > > +
> > > + /*
> > > + * SDR timings are given in pico-seconds while NFC timings must be
> > > + * expressed in NAND controller clock cycles.
> > > + */
> > > + mckperiodps = NSEC_PER_SEC / clk_get_rate(xnfc->mclk);
> > > + mckperiodps *= 1000;
> > > + if (sdr->tRC_min <= 20000)
> > > + /*
> > > + * PL353 SMC needs one extra read cycle in SDR Mode 5
> > > + * This is not written anywhere in the datasheet but
> > > + * the results observed during testing.
> > > + */
> > > + timings[0] = DIV_ROUND_UP(sdr->tRC_min, mckperiodps) + 1;
> > > + else
> > > + timings[0] = DIV_ROUND_UP(sdr->tRC_min, mckperiodps);
> > > +
> > > + timings[1] = DIV_ROUND_UP(sdr->tWC_min, mckperiodps);
> > > + /*
> > > + * For all SDR modes, PL353 SMC needs tREA max value as 1,
> > > + * Results observed during testing.
> > > + */
> > > + timings[2] = PL353_TREA_MAX_VALUE;
> > > + timings[3] = DIV_ROUND_UP(sdr->tWP_min, mckperiodps);
> > > + timings[4] = DIV_ROUND_UP(sdr->tCLR_min, mckperiodps);
> > > + timings[5] = DIV_ROUND_UP(sdr->tAR_min, mckperiodps);
> > > + timings[6] = DIV_ROUND_UP(sdr->tRR_min, mckperiodps);
> > > + pl353_smc_set_cycles(timings);
> > > +
> > > + return 0;
> > > +}
> >
> > If I hack this function in order to limit the timings only to mode 0,
> > everything works. Otherwise it hangs when it tries to apply mode 5.
> >
>
> Maybe Naga is not using a chip compatible with mode 5 and did not ran into this issue?
No, these are the chips I am using, S34ML01G1 and MT29F2G16ABAEAWP.
These are up to mode 5 compatible.

Thanks,
Naga Sureshkumar Relli
>
>
> Thanks,
> Miquèl
\
 
 \ /
  Last update: 2019-01-02 10:27    [W:0.063 / U:0.704 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site