lkml.org 
[lkml]   [2019]   [Jan]   [17]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH] arm64: dts: qcom: sdm845-mtp: Add WCN3990 BT node
Hi Anderson,

On 2019-01-17 10:10, Bjorn Andersson wrote:
> The SDM845 MTP has a WCN3990 Bluetooth chip on UART6, enable this.
>
> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
> ---
> arch/arm64/boot/dts/qcom/sdm845-mtp.dts | 44 +++++++++++++++++++++++++
> 1 file changed, 44 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/sdm845-mtp.dts
> b/arch/arm64/boot/dts/qcom/sdm845-mtp.dts
> index af8c6a2445a2..f65d5a674103 100644
> --- a/arch/arm64/boot/dts/qcom/sdm845-mtp.dts
> +++ b/arch/arm64/boot/dts/qcom/sdm845-mtp.dts
> @@ -17,6 +17,7 @@
>
> aliases {
> serial0 = &uart9;
> + hsuart0 = &uart6;
> };
>
> chosen {
> @@ -357,6 +358,10 @@
> clock-frequency = <400000>;
> };
>
> +&qupv3_id_0 {
> + status = "okay";
> +};
> +
> &qupv3_id_1 {
> status = "okay";
> };
> @@ -373,6 +378,20 @@
> cd-gpios = <&tlmm 126 GPIO_ACTIVE_LOW>;
> };
>
> +&uart6 {
> + status = "okay";
> +
> + bluetooth {
> + compatible = "qcom,wcn3990-bt";
> +
> + vddio-supply = <&vreg_s4a_1p8>;
> + vddxo-supply = <&vreg_l7a_1p8>;
> + vddrf-supply = <&vreg_l17a_1p3>;
> + vddch0-supply = <&vreg_l25a_3p3>;
> + max-speed = <3200000>;
> + };
> +};
> +
> &uart9 {
> status = "okay";
> };
> @@ -470,6 +489,31 @@
> };
> };
>
> +&qup_uart6_default {
> + pinmux {
> + pins = "gpio45", "gpio46", "gpio47", "gpio48";
> + function = "qup6";
> + };
> +
> + ctsrx {
> + pins = "gpio45", "gpio48";
> + drive-strength = <2>;
> + bias-no-pull;
> + };
> +
> + rts {
> + pins = "gpio46";
> + drive-strength = <2>;
> + bias-pull-down;
> + };
> +
> + tx {
> + pins = "gpio47";
> + drive-strength = <2>;
> + bias-pull-up;
> + };
> +};
> +
> &qup_uart9_default {
> pinconf-tx {
> pins = "gpio4";


[Bala]:
GPIO 45 is CTS
GPIO 46 is RTS
GPIO 47 is Tx
GPIO 48 is Rx.

Tx & RTS are inputs to APPS processor, bias should be disable as
the source i.e. BT chip will pull them up.
CTS & RX are outputs from APPS processor, where as CTS is GPIO
which need to toggled, so the default state should be pull down.
RX is should be pulled up.
when TX & RX are pulled high it indicates that the lines are
ideal i.e. no data.

Above is just my assumption, not sure whether they work on MTP.

--
Regards
Balakrishna.

\
 
 \ /
  Last update: 2019-01-17 07:10    [W:0.095 / U:5.040 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site