lkml.org 
[lkml]   [2019]   [Jan]   [15]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH shawn/for-next v4 2/2] ARM: dts: imx: Add Y Soft IOTA Draco, Hydra and Ursa boards
On Tue, 15 Jan 2019 14:22:45 +0000, =?utf-8?B?Vm9rw6HEjSBNaWNoYWw=?= wrote:
> These are i.MX6S/DL based SBCs embedded in various Y Soft products.
> All share the same board design but have slightly different HW
> configuration.
>
> Ursa
> - i.MX6S SoC, 512MB RAM DDR3, 4GB eMMC, microSD
> - parallel WVGA 7" LCD with touch panel
> - 1x Eth (QCA8334 switch)
> - USB OTG
> - USB host (micro-B)
>
> Draco
> - i.MX6S SoC, 512MB RAM DDR3, 4GB eMMC, microSD
> - parallel WVGA 7" LCD with touch panel
> - 2x Eth (QCA8334 switch)
> - USB OTG
> - USB host (micro-B)
> - RGB LED (I2C LP5562)
> - 3.5mm audio jack + codec (LM49350)
>
> Hydra
> - i.MX6DL SoC, 2GB RAM DDR3, 4GB eMMC, microSD
> - I2C OLED display, capacitive matrix keys
> - 2x Eth (QCA8334 switch)
> - USB OTG
> - RGB LED (I2C LP5562)
> - 3.5mm audio jack + codec (LM49350)
> - HDMI
> - miniPCIe slot
>
> Cc: Andrew Lunn <andrew@lunn.ch>
> Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
> ---
> Changes since v3:
> - Do not abbreviate regulator word in node names. (Shawn)
> - Sort fixed regulator nodes alphabetically.
> - Sort pmic regulator childe nodes alphabetically.
> - Use newline between properties and child node in switch node. (Shawn)
> - Sort i2c bus child nodes in order of unit-address. (Shawn)
> - Rename PWM pinctl label to be consistent with node name. (Shawn)
>
> Changes since v2:
> - Remove cpus {/delete-node/ cpu@1;}; node from i.MX6Solo based board. (Fabio)
> - Use "device_type = "memory";" in memory nodes. (Fabio)
> - Use GPIO_ACTIVE_LOW for fec phy-reset-gpios. (Fabio)
> - Use "-" in node names. (Rob)
> - Remove label from led-controller node. (Rob)
>
> Changes since v1:
> - Enable HDMI on Hydra board.
> - Move regulators to the root node and remove simple-bus property. (Rob)
> - Remove reg and unit-address property from regulators. (Rob)
> - Use correct names for led-controller and pmic node. (Rob)
> - Use wakeup-source instead of deprecated enable-sdio-wakeup. (Shawn)
>
> arch/arm/boot/dts/Makefile | 3 +
> arch/arm/boot/dts/imx6dl-yapp4-common.dtsi | 595 +++++++++++++++++++++++++++++
> arch/arm/boot/dts/imx6dl-yapp4-draco.dts | 58 +++
> arch/arm/boot/dts/imx6dl-yapp4-hydra.dts | 50 +++
> arch/arm/boot/dts/imx6dl-yapp4-ursa.dts | 54 +++
> 5 files changed, 760 insertions(+)
> create mode 100644 arch/arm/boot/dts/imx6dl-yapp4-common.dtsi
> create mode 100644 arch/arm/boot/dts/imx6dl-yapp4-draco.dts
> create mode 100644 arch/arm/boot/dts/imx6dl-yapp4-hydra.dts
> create mode 100644 arch/arm/boot/dts/imx6dl-yapp4-ursa.dts
>

Reviewed-by: Rob Herring <robh@kernel.org>

\
 
 \ /
  Last update: 2019-01-15 21:12    [W:0.102 / U:31.372 seconds]
©2003-2018 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site