lkml.org 
[lkml]   [2019]   [Jan]   [10]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH 1/2] dt-bindings: serial: Convert snps,dw-apb-uart to json-schema
Date
Convert the snps,dw-apb-uart binding to DT schema using json-schema.

The Rockchip and Broadcom compatible strings were not documented,
so add them here.

Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
---
.../bindings/serial/snps-dw-apb-uart.txt | 76 ----------
.../bindings/serial/snps-dw-apb-uart.yaml | 140 ++++++++++++++++++
2 files changed, 140 insertions(+), 76 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/serial/snps-dw-apb-uart.txt
create mode 100644 Documentation/devicetree/bindings/serial/snps-dw-apb-uart.yaml

diff --git a/Documentation/devicetree/bindings/serial/snps-dw-apb-uart.txt b/Documentation/devicetree/bindings/serial/snps-dw-apb-uart.txt
deleted file mode 100644
index 12bbe9f22560..000000000000
--- a/Documentation/devicetree/bindings/serial/snps-dw-apb-uart.txt
+++ /dev/null
@@ -1,76 +0,0 @@
-* Synopsys DesignWare ABP UART
-
-Required properties:
-- compatible : "snps,dw-apb-uart"
-- reg : offset and length of the register set for the device.
-- interrupts : should contain uart interrupt.
-
-Clock handling:
-The clock rate of the input clock needs to be supplied by one of
-- clock-frequency : the input clock frequency for the UART.
-- clocks : phandle to the input clock
-
-The supplying peripheral clock can also be handled, needing a second property
-- clock-names: tuple listing input clock names.
- Required elements: "baudclk", "apb_pclk"
-
-Optional properties:
-- snps,uart-16550-compatible : reflects the value of UART_16550_COMPATIBLE
- configuration parameter. Define this if your UART does not implement the busy
- functionality.
-- resets : phandle to the parent reset controller.
-- reg-shift : quantity to shift the register offsets by. If this property is
- not present then the register offsets are not shifted.
-- reg-io-width : the size (in bytes) of the IO accesses that should be
- performed on the device. If this property is not present then single byte
- accesses are used.
-- dcd-override : Override the DCD modem status signal. This signal will always
- be reported as active instead of being obtained from the modem status
- register. Define this if your serial port does not use this pin.
-- dsr-override : Override the DTS modem status signal. This signal will always
- be reported as active instead of being obtained from the modem status
- register. Define this if your serial port does not use this pin.
-- cts-override : Override the CTS modem status signal. This signal will always
- be reported as active instead of being obtained from the modem status
- register. Define this if your serial port does not use this pin.
-- ri-override : Override the RI modem status signal. This signal will always be
- reported as inactive instead of being obtained from the modem status register.
- Define this if your serial port does not use this pin.
-
-Example:
-
- uart@80230000 {
- compatible = "snps,dw-apb-uart";
- reg = <0x80230000 0x100>;
- clock-frequency = <3686400>;
- interrupts = <10>;
- reg-shift = <2>;
- reg-io-width = <4>;
- dcd-override;
- dsr-override;
- cts-override;
- ri-override;
- };
-
-Example with one clock:
-
- uart@80230000 {
- compatible = "snps,dw-apb-uart";
- reg = <0x80230000 0x100>;
- clocks = <&baudclk>;
- interrupts = <10>;
- reg-shift = <2>;
- reg-io-width = <4>;
- };
-
-Example with two clocks:
-
- uart@80230000 {
- compatible = "snps,dw-apb-uart";
- reg = <0x80230000 0x100>;
- clocks = <&baudclk>, <&apb_pclk>;
- clock-names = "baudclk", "apb_pclk";
- interrupts = <10>;
- reg-shift = <2>;
- reg-io-width = <4>;
- };
diff --git a/Documentation/devicetree/bindings/serial/snps-dw-apb-uart.yaml b/Documentation/devicetree/bindings/serial/snps-dw-apb-uart.yaml
new file mode 100644
index 000000000000..b42002542690
--- /dev/null
+++ b/Documentation/devicetree/bindings/serial/snps-dw-apb-uart.yaml
@@ -0,0 +1,140 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/serial/snps-dw-apb-uart.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Synopsys DesignWare ABP UART
+
+maintainers:
+ - Rob Herring <robh@kernel.org>
+
+allOf:
+ - $ref: /schemas/serial.yaml#
+
+properties:
+ compatible:
+ oneOf:
+ - items:
+ - enum:
+ - renesas,r9a06g032-uart
+ - renesas,r9a06g033-uart
+ - const: renesas,rzn1-uart
+ - items:
+ - enum:
+ - rockchip,px30-uart
+ - rockchip,rk3036-uart
+ - rockchip,rk3066-uart
+ - rockchip,rk3188-uart
+ - rockchip,rk3288-uart
+ - rockchip,rk3328-uart
+ - rockchip,rk3368-uart
+ - rockchip,rk3399-uart
+ - rockchip,rv1108-uart
+ - const: snps,dw-apb-uart
+ - items:
+ - enum:
+ - brcm,bcm11351-dw-apb-uart
+ - brcm,bcm21664-dw-apb-uart
+ - const: snps,dw-apb-uart
+ - const: snps,dw-apb-uart
+
+ reg:
+ maxItems: 1
+
+ interrupts:
+ maxItems: 1
+
+ clock-frequency: true
+
+ clocks:
+ minItems: 1
+ maxItems: 2
+
+ clock-names:
+ items:
+ - const: baudclk
+ - const: apb_pclk
+
+ snps,uart-16550-compatible:
+ description: reflects the value of UART_16550_COMPATIBLE configuration
+ parameter. Define this if your UART does not implement the busy functionality.
+ type: boolean
+
+ resets:
+ maxItems: 1
+
+ reg-shift: true
+
+ reg-io-width: true
+
+ dcd-override:
+ description: Override the DCD modem status signal. This signal will
+ always be reported as active instead of being obtained from the modem
+ status register. Define this if your serial port does not use this
+ pin.
+ type: boolean
+
+ dsr-override:
+ description: Override the DTS modem status signal. This signal will
+ always be reported as active instead of being obtained from the modem
+ status register. Define this if your serial port does not use this
+ pin.
+ type: boolean
+
+ cts-override:
+ description: Override the CTS modem status signal. This signal will
+ always be reported as active instead of being obtained from the modem
+ status register. Define this if your serial port does not use this
+ pin.
+ type: boolean
+
+ ri-override:
+ description: Override the RI modem status signal. This signal will always
+ be reported as inactive instead of being obtained from the modem status
+ register. Define this if your serial port does not use this pin.
+ type: boolean
+
+required:
+ - compatible
+ - reg
+ - interrupts
+
+examples:
+ - |
+ serial@80230000 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x80230000 0x100>;
+ clock-frequency = <3686400>;
+ interrupts = <10>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ dcd-override;
+ dsr-override;
+ cts-override;
+ ri-override;
+ };
+
+ - |
+ // Example with one clock:
+ serial@80230000 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x80230000 0x100>;
+ clocks = <&baudclk>;
+ interrupts = <10>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ };
+
+ - |
+ // Example with two clocks:
+ serial@80230000 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x80230000 0x100>;
+ clocks = <&baudclk>, <&apb_pclk>;
+ clock-names = "baudclk", "apb_pclk";
+ interrupts = <10>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ };
+...
--
2.19.1
\
 
 \ /
  Last update: 2019-01-10 23:21    [W:0.118 / U:18.060 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site