Messages in this thread Patch in this message |  | | Date | Mon, 3 Sep 2018 10:36:00 +0200 | From | Boris Brezillon <> | Subject | Re: [PATCH 1/7] spi: add slave device size in spi_device struct |
| |
Hi Yogesh,
On Mon, 3 Sep 2018 04:47:25 +0000 Yogesh Narayan Gaur <yogeshnarayan.gaur@nxp.com> wrote:
> Hi Lothar, > > > -----Original Message----- > > From: Lothar Waßmann [mailto:LW@KARO-electronics.de] > > Sent: Friday, August 31, 2018 5:28 PM > > To: Yogesh Narayan Gaur <yogeshnarayan.gaur@nxp.com> > > Cc: linux-mtd@lists.infradead.org; boris.brezillon@bootlin.com; > > marek.vasut@gmail.com; linux-spi@vger.kernel.org; > > devicetree@vger.kernel.org; mark.rutland@arm.com; robh@kernel.org; linux- > > kernel@vger.kernel.org; frieder.schrempf@exceet.de; > > computersforpeace@gmail.com; shawnguo@kernel.org; linux-arm- > > kernel@lists.infradead.org > > Subject: Re: [PATCH 1/7] spi: add slave device size in spi_device struct > > > > Hi, > > > > On Fri, 31 Aug 2018 15:59:58 +0530 Yogesh Gaur wrote: > > > Add 'size' data variable in spi_device struct. > > > This is to save the size of the connected slave device. > > > > > > After slave device scan, spi_nor_scan, size being assigned to this > > > from MTD layer. > > > > > > SFDP read is being requested before completion of spi_nor_scan() > > > routine, thus populate device size before making read request to the > > > SPI controller. > > > > > > Signed-off-by: Yogesh Gaur <yogeshnarayan.gaur@nxp.com> > > > --- > > > drivers/mtd/devices/m25p80.c | 6 ++++++ > > > drivers/mtd/spi-nor/spi-nor.c | 2 ++ > > > include/linux/spi/spi.h | 2 ++ > > > 3 files changed, 10 insertions(+) > > > > > > diff --git a/drivers/mtd/devices/m25p80.c > > > b/drivers/mtd/devices/m25p80.c index fe260cc..6c7ad86 100644 > > > --- a/drivers/mtd/devices/m25p80.c > > > +++ b/drivers/mtd/devices/m25p80.c > > > @@ -124,6 +124,10 @@ static ssize_t m25p80_read(struct spi_nor *nor, > > loff_t from, size_t len, > > > /* convert the dummy cycles to the number of bytes */ > > > op.dummy.nbytes = (nor->read_dummy * op.dummy.buswidth) / 8; > > > > > > + /* for case of SFDP header read commands, populate spi device size */ > > > + if (flash->spimem->spi->size == 0) > > > + flash->spimem->spi->size = nor->mtd.size; > > > + > > If the 'size' is an spimem specific variable it should be added to the spi_mem > > struct rather than the spi_device struct. > > Sure, would move 'size' from struct spi_device to the struct spi_mem.
Before you send a new version doing that, I'd like to understand why you need this information. Can you wait a bit so I have some time to review the driver?
Thanks,
Boris
|  |