lkml.org 
[lkml]   [2018]   [Sep]   [3]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRE: [PATCH 1/7] spi: add slave device size in spi_device struct
Date
Hi Lothar,

> -----Original Message-----
> From: Lothar Waßmann [mailto:LW@KARO-electronics.de]
> Sent: Friday, August 31, 2018 5:28 PM
> To: Yogesh Narayan Gaur <yogeshnarayan.gaur@nxp.com>
> Cc: linux-mtd@lists.infradead.org; boris.brezillon@bootlin.com;
> marek.vasut@gmail.com; linux-spi@vger.kernel.org;
> devicetree@vger.kernel.org; mark.rutland@arm.com; robh@kernel.org; linux-
> kernel@vger.kernel.org; frieder.schrempf@exceet.de;
> computersforpeace@gmail.com; shawnguo@kernel.org; linux-arm-
> kernel@lists.infradead.org
> Subject: Re: [PATCH 1/7] spi: add slave device size in spi_device struct
>
> Hi,
>
> On Fri, 31 Aug 2018 15:59:58 +0530 Yogesh Gaur wrote:
> > Add 'size' data variable in spi_device struct.
> > This is to save the size of the connected slave device.
> >
> > After slave device scan, spi_nor_scan, size being assigned to this
> > from MTD layer.
> >
> > SFDP read is being requested before completion of spi_nor_scan()
> > routine, thus populate device size before making read request to the
> > SPI controller.
> >
> > Signed-off-by: Yogesh Gaur <yogeshnarayan.gaur@nxp.com>
> > ---
> > drivers/mtd/devices/m25p80.c | 6 ++++++
> > drivers/mtd/spi-nor/spi-nor.c | 2 ++
> > include/linux/spi/spi.h | 2 ++
> > 3 files changed, 10 insertions(+)
> >
> > diff --git a/drivers/mtd/devices/m25p80.c
> > b/drivers/mtd/devices/m25p80.c index fe260cc..6c7ad86 100644
> > --- a/drivers/mtd/devices/m25p80.c
> > +++ b/drivers/mtd/devices/m25p80.c
> > @@ -124,6 +124,10 @@ static ssize_t m25p80_read(struct spi_nor *nor,
> loff_t from, size_t len,
> > /* convert the dummy cycles to the number of bytes */
> > op.dummy.nbytes = (nor->read_dummy * op.dummy.buswidth) / 8;
> >
> > + /* for case of SFDP header read commands, populate spi device size */
> > + if (flash->spimem->spi->size == 0)
> > + flash->spimem->spi->size = nor->mtd.size;
> > +
> If the 'size' is an spimem specific variable it should be added to the spi_mem
> struct rather than the spi_device struct.

Sure, would move 'size' from struct spi_device to the struct spi_mem.

--
Regards
Yogesh Gaur.

>
> Lothar Waßmann
\
 
 \ /
  Last update: 2018-09-03 06:48    [W:0.075 / U:0.308 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site