lkml.org 
[lkml]   [2018]   [Sep]   [19]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [RFC] net;sched: Try to find idle cpu for RPS to handle packets
From
Date
On 19.09.2018 18:49, Eric Dumazet wrote:
> On Wed, Sep 19, 2018 at 8:41 AM Kirill Tkhai <ktkhai@virtuozzo.com> wrote:
>>
>> On 19.09.2018 17:55, Eric Dumazet wrote:
>>> On Wed, Sep 19, 2018 at 5:29 AM Kirill Tkhai <ktkhai@virtuozzo.com> wrote:
>>>>
>>>> Many workloads have polling mode of work. The application
>>>> checks for incomming packets from time to time, but it also
>>>> has a work to do, when there is no packets. This RFC
>>>> tries to develop an idea to queue RPS packets on idle
>>>> CPU in the the L3 domain of the consumer, so backlog
>>>> processing of the packets and the application can execute
>>>> in parallel.
>>>>
>>>> We require this in case of network cards does not
>>>> have enough RX queues to cover all online CPUs (this seems
>>>> to be the most cards), and get_rps_cpu() actually chooses
>>>> remote cpu, and SMP interrupt is sent. Here we may try
>>>> our best, and to find idle CPU nearly the consumer's CPU.
>>>> Note, that in case of consumer works in poll mode and it
>>>> does not waits for incomming packets, its CPU will be not
>>>> idle, while CPU of a sleeping consumer may be idle. So,
>>>> not polling consumers will still be able to have skb
>>>> handled on its CPU.
>>>>
>>>> In case of network card has many queues, the device
>>>> interrupts will come on consumer's CPU, and this patch
>>>> won't try to find idle cpu for them.
>>>>
>>>> I've tried simple netperf test for this:
>>>> netserver -p 1234
>>>> netperf -L 127.0.0.1 -p 1234 -l 100
>>>>
>>>> Before:
>>>> 87380 16384 16384 100.00 60323.56
>>>> 87380 16384 16384 100.00 60388.46
>>>> 87380 16384 16384 100.00 60217.68
>>>> 87380 16384 16384 100.00 57995.41
>>>> 87380 16384 16384 100.00 60659.00
>>>>
>>>> After:
>>>> 87380 16384 16384 100.00 64569.09
>>>> 87380 16384 16384 100.00 64569.25
>>>> 87380 16384 16384 100.00 64691.63
>>>> 87380 16384 16384 100.00 64930.14
>>>> 87380 16384 16384 100.00 62670.15
>>>>
>>>> The difference between best runs is +7%,
>>>> the worst runs differ +8%.
>>>>
>>>> What do you think about following somehow in this way?
>>>
>>> Hi Kirill
>>>
>>> In my experience, scheduler has a poor view of softirq processing
>>> happening on various cpus.
>>> A cpu spending 90% of its cycles processing IRQ might be considered 'idle'
>>
>> Yes, in case of there is softirq on top of irq_exit(), the cpu is not
>> considered as busy. But after MAX_SOFTIRQ_TIME (=2ms), ksoftirqd are
>> waken up to execute the work in process context, and the processor is
>> considered as !idle. 2ms is 2 timer ticks in case of HZ=1000. So, we
>> don't restart softirq in case of it was executed for more then 2ms.
>>
>
> That's the theory, but reality is very different unfortunately.
>
> If RFS/RPS is setup properly, we really do not hit MAX_SOFTIRQ_TIME condition
> unless in some synthetic benchmarks maybe.
>
>> The similar way, single net_rx_action() can't be executed longer
>> than 2ms.
>>
>> Having 90% load in softirq (called on top of irq_exit()) should be
>> very unlikely situation, when there are too many interrupts with small
>> amount of work, which related softirq calls are doing for each of them.
>> I think it had be a problem even in plain napi case, since it would
>> worked not like expected.
>>
>> But anyway. You worry, that during handling of next portion of skbs,
>> we find that previous portion of skbs already woken ksoftirqd, and
>> we don't see this cpu as idle? Yeah, then we'll try to change cpu,
>> and this is not what we want. We want to continue use the cpu, where
>> previous portion was handler. Hm, not so fast I'll answer, but certainly,
>> this may be handled somehow in more creative way.
>>
>>> So please run a real workload (it is _very_ uncommon anyone set up RPS
>>> on lo interface !)
>>>
>>> Like 400 or more concurrent netperf -t TCP_RR on a 10Gbit NIC.
>>
>> Yeah, it's just a simulation of a single irq nic. I'll try on something
>> more real hardware.
>
> Also my concern is that you might have results that are tied to a particular
> version of process scheduling, platform, workload...
>
> One month later, a small change in process scheduler,
> and very different results.

Maybe, but especially that function logic has not changed for a long time.
10 years at least. The only change is Peter adds idle core searching
functionality recently.

> This is why I believe this new feature must be controllable, via a new
> tunable (like RPS/RFS are controllable per rx queue)
>
>>
>> How do you execute such the tests? I don't see the appropriate parameter
>> of netperf. Does this mean just to start 400 copies of netperf? How is
>> to aggregate their results in this case?
>
> Yeah, there are various 'super_netperf' scripts available on the net
> (almost trivial to write anyway)
>
> ( I am attaching one of them)

Thanks.

> Thanks.
>>
>>> Thanks.
>>>
>>> PS: Idea of playing with L3 domains is interesting, I have personally
>>> tried various strategies in the past but none of them
>>> demonstrated a clear win.
>>
>> Thanks,
>> Kirill

\
 
 \ /
  Last update: 2018-09-19 18:00    [W:0.056 / U:0.948 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site