lkml.org 
[lkml]   [2018]   [Sep]   [12]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v4 1/2] phy: zynqmp: Add dt bindings for ZynqMP phy
Date
This patch adds the document describing dt bindings for ZynqMP
phy. ZynqMP SOC has a High Speed Processing System Gigabit
Transceiver which provides PHY capabilties to USB, SATA,
PCIE, Display Port and Ehernet SGMII controllers.

Signed-off-by: Anurag Kumar Vulisha <anurag.kumar.vulisha@xilinx.com>
---
Changes in v4:
1. Fixed the changes in phy-zynqmp.txt as suggested by "Rob Herring"
2. Moved changes from include/dt-bindings/phy/phy.h into Patch 2 to 1

Changes in v3:
1. Corrected the Documentation as suggested by "Vivek Gautam"

Changes in v2:
1. None
---
.../devicetree/bindings/phy/phy-zynqmp.txt | 109 +++++++++++++++++++++
include/dt-bindings/phy/phy.h | 2 +
2 files changed, 111 insertions(+)
create mode 100644 Documentation/devicetree/bindings/phy/phy-zynqmp.txt

diff --git a/Documentation/devicetree/bindings/phy/phy-zynqmp.txt b/Documentation/devicetree/bindings/phy/phy-zynqmp.txt
new file mode 100644
index 0000000..ed501c4
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/phy-zynqmp.txt
@@ -0,0 +1,109 @@
+Xilinx ZynqMP PHY binding
+
+This binding describes a ZynqMP PHY device that is used to control ZynqMP
+High Speed Gigabit Transceiver(GT). ZynqMP PS GTR provides four lanes
+and are used by USB, SATA, PCIE, Display port and Ethernet SGMMI controllers.
+
+Phy provider node
+=================
+
+Required properties:
+- compatible : Can be "xlnx,zynqmp-psgtr-v1.1" or "xlnx,zynqmp-psgtr"
+
+- reg : Address and length of register sets for each device in
+ "reg-names"
+
+- reg-names : The names of the register addresses corresponding to the
+ registers filled in "reg":
+ - serdes: SERDES block register set
+ - siou: SIOU block register set
+
+Optional properties:
+- xlnx,tx-termination-fix : Include this for fixing functional issue with the
+ TX termination resistance in GT, which can be out of spec for
+ the XCZU9EG silicon version. This property is not required for
+ "xlnx,zynqmp-psgtr-v1.1"
+
+Required nodes : A sub-node is required for each lane the controller
+ provides.
+
+Phy sub-nodes
+=============
+
+Required properties:
+lane@0:
+- #phy-cells : Should be 4
+
+lane@1:
+- #phy-cells : Should be 4
+
+lane@2:
+- #phy-cells : Should be 4
+
+lane@3:
+- #phy-cells : Should be 4
+
+Example:
+ zynqmp_phy: phy@fd400000 {
+ compatible = "xlnx,zynqmp-psgtr-v1.1";
+ status = "okay";
+ reg = <0x0 0xfd400000 0x0 0x40000>, <0x0 0xfd3d0000 0x0 0x1000>;
+ reg-names = "serdes", "siou";
+
+ lane0: lane@0 {
+ #phy-cells = <4>;
+ };
+ lane1: lane@1 {
+ #phy-cells = <4>;
+ };
+ lane2: lane@2 {
+ #phy-cells = <4>;
+ };
+ lane3: lane@3 {
+ #phy-cells = <4>;
+ };
+ };
+
+Specifying phy control of devices
+=================================
+
+Device nodes should specify the configuration required in their "phys"
+property, containing a phandle to the phy port node and a device type.
+
+phys = <PHANDLE CONTROLLER_TYPE CONTROLLER_INSTANCE LANE_REF_CLK LANE_FREQ>;
+
+PHANDLE = &lane0 or &lane1 or &lane2 or &lane3
+CONTROLLER_TYPE = PHY_TYPE_PCIE or PHY_TYPE_SATA or PHY_TYPE_USB
+ or PHY_TYPE_DP or PHY_TYPE_SGMII
+CONTROLLER_INSTANCE = Depends on controller type used, can be any of
+ PHY_TYPE_PCIE : 0 or 1 or 2 or 3
+ PHY_TYPE_SATA : 0 or 1
+ PHY_TYPE_USB : 0 or 1
+ PHY_TYPE_DP : 0 or 1
+ PHY_TYPE_SGMII: 0 or 1 or 2 or 3
+LANE_REF_CLK = Depends on which lane clock is used as ref clk, can be
+ 0 or 1 or 2 or 3
+LANE_FREQ = Frequency of the reference clock, can be any of the
+ below mentioned based on the phy type used
+- PHY_TYPE_PCIE = 100Mhz
+- PHY_TYPE_SGMII = 125Mhz
+- PHY_TYPE_SATA = 125Mhz, 150Mhz
+- PHY_TYPE_USB = 26Mhz, 52Mhz, 100Mhz
+- PHY_TYPE_DP = 27Mhz, 108Mhz, 135Mhz
+
+Example:
+
+#include <dt-bindings/phy/phy.h>
+
+ usb@fe200000 {
+ ...
+ phys = <&lane2 PHY_TYPE_USB3 0 2 2600000>;
+ ...
+ };
+
+ zynqmp-display@fd4a0000 {
+ ...
+ phys = <&lane1 PHY_TYPE_DP 0 1 27000000>,
+ <&lane0 PHY_TYPE_DP 1 1 27000000>;
+ ...
+ };
diff --git a/include/dt-bindings/phy/phy.h b/include/dt-bindings/phy/phy.h
index d16e875..09cc0a6 100644
--- a/include/dt-bindings/phy/phy.h
+++ b/include/dt-bindings/phy/phy.h
@@ -16,5 +16,7 @@
#define PHY_TYPE_USB2 3
#define PHY_TYPE_USB3 4
#define PHY_TYPE_UFS 5
+#define PHY_TYPE_DP 6
+#define PHY_TYPE_SGMII 7

#endif /* _DT_BINDINGS_PHY */
--
2.1.1
\
 
 \ /
  Last update: 2018-09-12 18:24    [W:0.072 / U:3.432 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site