lkml.org 
[lkml]   [2018]   [Sep]   [12]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH v2 2/2] dmaengine: uniphier-mdmac: add UniPhier MIO DMAC driver
2018-09-12 13:35 GMT+09:00 Vinod <vkoul@kernel.org>:
> On 12-09-18, 12:01, Masahiro Yamada wrote:
>> Hi Vinod,
>>
>>
>> 2018-09-11 16:00 GMT+09:00 Vinod <vkoul@kernel.org>:
>> > On 24-08-18, 10:41, Masahiro Yamada wrote:
>> >
>> >> +/* mc->vc.lock must be held by caller */
>> >> +static u32 __uniphier_mdmac_get_residue(struct uniphier_mdmac_desc *md)
>> >> +{
>> >> + u32 residue = 0;
>> >> + int i;
>> >> +
>> >> + for (i = md->sg_cur; i < md->sg_len; i++)
>> >> + residue += sg_dma_len(&md->sgl[i]);
>> >
>> > so if the descriptor is submitted to hardware, we return the descriptor
>> > length, which is not correct.
>> >
>> > Two cases are required to be handled:
>> > 1. Descriptor is in queue (IMO above logic is fine for that, but it can
>> > be calculated at descriptor submit and looked up here)
>>
>> Where do you want it to be calculated?
>
> where is it calculated now?


Please see __uniphier_mdmac_handle().


It gets the address and size by sg_dma_address(), sg_dma_len()
just before setting them to the hardware registers.


sg = &md->sgl[md->sg_cur];

if (md->dir == DMA_MEM_TO_DEV) {
src_mode = UNIPHIER_MDMAC_CH_MODE__ADDR_INC;
src_addr = sg_dma_address(sg);
dest_mode = UNIPHIER_MDMAC_CH_MODE__ADDR_FIXED;
dest_addr = 0;
} else {
src_mode = UNIPHIER_MDMAC_CH_MODE__ADDR_FIXED;
src_addr = 0;
dest_mode = UNIPHIER_MDMAC_CH_MODE__ADDR_INC;
dest_addr = sg_dma_address(sg);
}







>> This hardware provides only simple registers (address and size)
>> for one-shot transfer instead of descriptors.
>>
>> So, I used sgl as-is because I did not see a good reason
>> to transform sgl to another data structure.
>
>
>> > this seems missing stuff. Where do you do register calculation for the
>> > descriptor and where is slave_config here, how do you know where to
>> > send/receive data form/to (peripheral)
>>
>>
>> This dmac is really simple, and un-flexible.
>>
>> The peripheral address to send/receive data from/to is hard-weird.
>> cfg->{src_addr,dst_addr} is not configurable.
>>
>> Look at __uniphier_mdmac_handle().
>> 'dest_addr' and 'src_addr' must be set to 0 for the peripheral.
>
> Fair enough, what about other values like addr_width and maxburst?


None of them is configurable.



--
Best Regards
Masahiro Yamada

\
 
 \ /
  Last update: 2018-09-12 07:27    [W:0.101 / U:20.176 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site