lkml.org 
[lkml]   [2018]   [Aug]   [7]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v1 5/5] tinydrm: add winstar wg160160 driver
From
Date

Den 02.08.2018 21.45, skrev Sam Ravnborg:
> Add driver for the winstar wg160160 display.
> The driver utilises pardata-dbi that
> again utilise the pardata subsystem.
>
> Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
> ---
> MAINTAINERS | 5 +
> drivers/gpu/drm/tinydrm/Kconfig | 10 ++
> drivers/gpu/drm/tinydrm/Makefile | 1 +
> drivers/gpu/drm/tinydrm/wg160160.c | 298 +++++++++++++++++++++++++++++++++++++
> 4 files changed, 314 insertions(+)
> create mode 100644 drivers/gpu/drm/tinydrm/wg160160.c
>

[...]

> +
> +/**
> + * write_reg - Write instruction on parallel bus to controller
> + *
> + * Check BUSY flag and write instruction
> + *
> + * @pdd: pardata data
> + * @reg: The register to write
> + * @value: The value of the register
> + *
> + * Returns:
> + * Zero on success, negative error code on failure
> + */
> +int write_reg(struct pardata_data *pdd, unsigned int reg, unsigned int value)
> +{
> + int ins[PIN_NUM];
> + int val[PIN_NUM];
> + int i;
> +
> + for (i = 0; i < PIN_NUM; i++)
> + ins[PIN_DB0 + i] = !!BIT(reg);
> +
> + for (i = 0; i < PIN_NUM; i++)
> + val[PIN_DB0 + i] = !!(value & BIT(i));
> +
> + gpiod_set_value_cansleep(pdd->bus->pin_rs, 1);
> + gpiod_set_array_value_cansleep(PIN_NUM, pdd->bus->data_pins->desc, ins);
> + wait_busy(pdd);
> + pardata_strobe_write(pdd);
> +
> + gpiod_set_value_cansleep(pdd->bus->pin_rs, 0);
> + gpiod_set_array_value_cansleep(PIN_NUM, pdd->bus->data_pins->desc, val);
> + wait_busy(pdd);
> + pardata_strobe_write(pdd);
> +
> + return 0;
> +}

If this controller has normal registers, you could do a regmap
implementation for pardata: drivers/base/regmap.

Noralf.

> +
> +/**
> + * write_buf - write buffer on parallel bus to controller
> + *
> + * @pdd: pardata data
> + * @offset: offset into display RAM
> + * @data: pointer to data to write
> + * @len: number of bytes to write
> + *
> + * Returns:
> + * Zero on success, negative error code on failure
> + */
> +int write_buf(struct pardata_data *pdd, u8 offset, u8 *data, size_t len)
> +{
> + int ins[PIN_NUM];
> + int val[PIN_NUM];
> + int bit;
> + int i;
> +
> + /* Setup address */
> + write_reg(pdd, WG160160_ADDRSL_REG, offset & 0xff);
> + write_reg(pdd, WG160160_ADDRSL_REG, (offset >> 8) & 0xff);
> +
> + /* prepare to write data */
> + for (i = 0; i < PIN_NUM; i++)
> + ins[PIN_DB0 + i] = !!(WG160160_WRITE_REG & BIT(i));
> +
> + gpiod_set_value_cansleep(pdd->bus->pin_rs, 1);
> + gpiod_set_array_value_cansleep(PIN_NUM, pdd->bus->data_pins->desc, ins);
> + wait_busy(pdd);
> + pardata_strobe_write(pdd);
> +
> + /* Write data byte - by byte */
> + gpiod_set_value_cansleep(pdd->bus->pin_rs, 0);
> +
> + for (i = offset; i < (offset + len); i++) {
> + for (bit = 0; bit < PIN_NUM; bit++)
> + val[PIN_DB0 + bit] = !!(data[i] & BIT(bit));
> +
> + gpiod_set_array_value_cansleep(PIN_NUM,
> + pdd->bus->data_pins->desc,
> + val);
> + wait_busy(pdd);
> + pardata_strobe_write(pdd);
> + }
> +
> + return 0;
> +}

\
 
 \ /
  Last update: 2018-08-07 19:37    [W:0.077 / U:8.412 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site