[lkml]   [2018]   [Aug]   [3]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
Messages in this thread
Subject[PATCH v2 0/4] phy: socionext: add new UniPhier USB PHY driver support
This series adds support for PHY interface built into USB controller
implemented in Socionext UniPhier SoCs.

The USB3 PHY driver supports High-Speed PHY and Super-Speed PHY included in
the USB3 glue layer, and the USB2 PHY driver supports High-Speed PHY
integrated into system controller.

Kunihiko Hayashi (4):
dt-bindings: phy: add DT bindings for UniPhier USB3 PHY driver
phy: socionext: add USB3 PHY driver for UniPhier SoC
dt-bindings: phy: add DT bindings for UniPhier USB2 PHY driver
phy: socionext: add USB2 PHY driver for UniPhier SoC

Changes since v1:
- rewrite a header with C++ comment style
- dt-bindings: separate a document for ssphy and hsphy
- dt-bindings: sort clock-names and reset-names to begin with "phy"
- dt-bindings: use vbus-supply instead of phy-supply, because vbus isn't
for phy, but vbus is tied to the port that corresponds to each phy [1]
- stop using phy_power and add own .power_on and .power_off functions
to control clk/reset for phy and vbus regulator
- separate clk_get() and reset_control_get() for each clk/reset
and remove arrays of clock_names and reset_names
- remove phy-parameters that are the same as power-on values
- remove functions to set phy-parameters for legacy SoCs
- express phy-parameters by using macros including the number of
the register and its bitfield (msb and lsb)


.../devicetree/bindings/phy/uniphier-usb2-phy.txt | 45 +++
.../bindings/phy/uniphier-usb3-hsphy.txt | 69 ++++
.../bindings/phy/uniphier-usb3-ssphy.txt | 57 +++
drivers/phy/Kconfig | 1 +
drivers/phy/Makefile | 1 +
drivers/phy/socionext/Kconfig | 25 ++
drivers/phy/socionext/Makefile | 7 +
drivers/phy/socionext/phy-uniphier-usb2.c | 246 ++++++++++++
drivers/phy/socionext/phy-uniphier-usb3hs.c | 423 +++++++++++++++++++++
drivers/phy/socionext/phy-uniphier-usb3ss.c | 350 +++++++++++++++++
10 files changed, 1224 insertions(+)
create mode 100644 Documentation/devicetree/bindings/phy/uniphier-usb2-phy.txt
create mode 100644 Documentation/devicetree/bindings/phy/uniphier-usb3-hsphy.txt
create mode 100644 Documentation/devicetree/bindings/phy/uniphier-usb3-ssphy.txt
create mode 100644 drivers/phy/socionext/Kconfig
create mode 100644 drivers/phy/socionext/Makefile
create mode 100644 drivers/phy/socionext/phy-uniphier-usb2.c
create mode 100644 drivers/phy/socionext/phy-uniphier-usb3hs.c
create mode 100644 drivers/phy/socionext/phy-uniphier-usb3ss.c


 \ /
  Last update: 2018-08-03 11:56    [W:0.073 / U:0.128 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site