lkml.org 
[lkml]   [2018]   [Aug]   [13]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH 1/4] ARM: dts: exynos: Add missing used PMIC regulators on Exynos5422 Odroid boards
On 13 August 2018 at 08:37, Anand Moon <linux.amoon@gmail.com> wrote:
> Hi Krzysztof,
>
> On Sun, 12 Aug 2018 at 18:55, Krzysztof Kozlowski <krzk@kernel.org> wrote:
>>
>> On 11 August 2018 at 08:39, Anand Moon <linux.amoon@gmail.com> wrote:
>> > Hi Krzysztof,
>> >
>> > These patches should also be ported to u-boot to enable PMIC.
>> >
>> > I was just looking into S2MPS11B data sheet
>> > According to the 1.2 Key Features of S2MPS11
>> >
>> > BUCK1, BUCK2, BUCK3, BUCK4, BUCK6 have (0.65 V to 1.6 V) min /max range.
>> > BUCK5 have (0.65 V to 2.0 V) min /max range.
>> > BUCK7 have (1.2 V to 1.5 V) min / max range.
>> > BUCK8 have (1.8 V to 2.1 V) min / max range.
>> > BUCK10 have (0.75 V to 1.4 V) min / max range.
>> >
>> > BUCKBOST9 (3.0 V to 3.75 V) min / max range.
>> >
>> > LDO1, LDO6, LDO11, LDO22, LDO23, LDO27, LDO35 (0.8 V to 2.375 V) min / max range
>> >
>> > LDO2, LDO3, LDO5, LDO7, LDO9, LDO10, LD012, LDO13, LDO14, LDO15,
>> > LDO16, LDO17, LDO18, LDO19, LDO20, LD021, LDO24, LDO25, LDO26,
>> > LDO28, LDO29, LDO30, LDO31, LDO32, LDO33, LDO34, LDO36, LDO37, LDO38
>> > (0.8 V to 3.95 V) min / max range
>> >
>> > I am aware off we have configures the min/max range as per board schematics.
>> > but each regulator support dynamic voltage scale and have different
>> > turn on/off voltage and current rating.
>> >
>> > So why are we not setting the regulator-min-microvolt /
>> > regulator-max-microvolt as per datasheets.
>> > Please correct me if I am wrong.
>>
>> Which regulators are not configured as in datasheet?
>>
>> Best regards,
>> Krzysztof
>
> Almost all the regulator have some miss default match of min/max setting.
> I have tried to adjust the setting on top your above patches.
>
> I am attaching my patch diff for testing.
> I have have perform some stress testing and found no issue at my end.

All the regulators you touched in this patch have proper setting of
min and max values. They are configured to the values required by
hardware, as in schematics.

Best regards,
Krzysztof

\
 
 \ /
  Last update: 2018-08-13 09:15    [W:0.059 / U:0.016 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site