lkml.org 
[lkml]   [2018]   [Jul]   [30]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v5 04/21] dt-bindings: Add doc for the Ingenic TCU drivers
Hi Rob,

Le mer. 25 juil. 2018 à 17:21, Rob Herring <robh@kernel.org> a écrit :
> On Wed, Jul 25, 2018 at 01:19:41AM +0200, Paul Cercueil wrote:
>> Add documentation about how to properly use the Ingenic TCU
>> (Timer/Counter Unit) drivers from devicetree.
>>
>> Signed-off-by: Paul Cercueil <paul@crapouillou.net>
>> ---
>> .../devicetree/bindings/pwm/ingenic,jz47xx-pwm.txt | 24 +---
>> .../devicetree/bindings/timer/ingenic,tcu.txt | 147
>> +++++++++++++++++++++
>> .../bindings/watchdog/ingenic,jz4740-wdt.txt | 17 +--
>> 3 files changed, 151 insertions(+), 37 deletions(-)
>> create mode 100644
>> Documentation/devicetree/bindings/timer/ingenic,tcu.txt
>>
>> v4: New patch in this series. Corresponds to V2 patches 3-4-5 with
>> added content.
>>
>> v5: - Edited PWM/watchdog DT bindings documentation to point to
>> the new
>> document.
>> - Moved main document to
>> Documentation/devicetree/bindings/timer/ingenic,tcu.txt
>> - Updated documentation to reflect the new devicetree bindings.
>>
>> diff --git
>> a/Documentation/devicetree/bindings/pwm/ingenic,jz47xx-pwm.txt
>> b/Documentation/devicetree/bindings/pwm/ingenic,jz47xx-pwm.txt
>> index 7d9d3f90641b..a722cdde3aa7 100644
>> --- a/Documentation/devicetree/bindings/pwm/ingenic,jz47xx-pwm.txt
>> +++ b/Documentation/devicetree/bindings/pwm/ingenic,jz47xx-pwm.txt
>> @@ -1,25 +1,5 @@
>> Ingenic JZ47xx PWM Controller
>> =============================
>>
>> -Required properties:
>> -- compatible: One of:
>> - * "ingenic,jz4740-pwm"
>> - * "ingenic,jz4770-pwm"
>> - * "ingenic,jz4780-pwm"
>> -- #pwm-cells: Should be 3. See pwm.txt in this directory for a
>> description
>> - of the cells format.
>> -- clocks : phandle to the external clock.
>> -- clock-names : Should be "ext".
>> -
>> -
>> -Example:
>> -
>> - pwm: pwm@10002000 {
>> - compatible = "ingenic,jz4740-pwm";
>> - reg = <0x10002000 0x1000>;
>> -
>> - #pwm-cells = <3>;
>> -
>> - clocks = <&ext>;
>> - clock-names = "ext";
>> - };
>> +This documentation has moved; for a description of the devicetree
>> bindings of
>> +this driver, please refer to ../timer/ingenic,tcu.txt.
>
> This should be evident from the git log. Just remove it.

Ok.

>> diff --git
>> a/Documentation/devicetree/bindings/timer/ingenic,tcu.txt
>> b/Documentation/devicetree/bindings/timer/ingenic,tcu.txt
>> new file mode 100644
>> index 000000000000..65d125b460aa
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/timer/ingenic,tcu.txt
>> @@ -0,0 +1,147 @@
>> +Ingenic JZ47xx SoCs Timer/Counter Unit devicetree bindings
>> +==========================================================
>> +
>> +For a description of the TCU hardware and drivers, have a look at
>> +Documentation/mips/ingenic-tcu.txt.
>> +
>> +Required properties:
>> +
>> +- compatible: Must be one of:
>> + * ingenic,jz4740-tcu
>> + * ingenic,jz4725b-tcu
>> + * ingenic,jz4770-tcu
>> +- reg: Should be the offset/length value corresponding to the TCU
>> registers
>
>> +- #address-cells: Should be <1>;
>> +- #size-cells: Should be <1>;
>> +- ranges: Should be one range for the full TCU registers area
>
> These can all be implied.

Ok.

>> +- clocks: List of phandle & clock specifiers for clocks external
>> to the TCU.
>> + The "pclk", "rtc", "ext" and "tcu" clocks should be provided.
>> +- clock-names: List of name strings for the external clocks.
>> +- #clock-cells: Should be <1>;
>> + Clock consumers specify this argument to identify a clock. The
>> valid values
>> + may be found in <dt-bindings/clock/ingenic,tcu.h>.
>> +- interrupt-controller : Identifies the node as an interrupt
>> controller
>> +- #interrupt-cells : Specifies the number of cells needed to
>> encode an
>> + interrupt source. The value should be 1.
>> +- interrupt-parent : phandle of the interrupt controller.
>> +- interrupts : Specifies the interrupt the controller is connected
>> to.
>
> How many and what are they. The example shows there are 3.

They are 2 or 3, and they are all the same (three parent IRQs for one
irqchip).
It's explained in the hardware doc, should I add it here as well?

>> +
>> +Optional properties:
>> +
>> +- ingenic,timer-channel: Specifies the TCU channel that should be
>> used as
>> + system timer. If not provided, the TCU channel 0 is used for the
>> system timer.
>> +
>> +- ingenic,clocksource-channel: Specifies the TCU channel that
>> should be used
>> + as clocksource and sched_clock. It must be a different channel
>> than the one
>> + used as system timer. If not provided, neither a clocksource nor
>> a
>> + sched_clock is instantiated.
>
> clocksource and sched_clock are Linux specific and don't belong in DT.
> You should define properties of the hardware or use existing
> properties
> like interrupts or clocks to figure out which channel to use. For
> example, if some channels don't have an interrupt, then use them for
> clocksource and not a clockevent. Or you could have timers that run in
> low-power modes or not. If all the channels are identical, then it
> shouldn't matter which ones the OS picks.

We already talked about that. All the TCU channels can be used for PWM.
The problem is I cannot know from the driver's scope which channels will
be free and which channels will be requested for PWM. You suggested
that I
parse the devicetree for clients, and I did that in the V3/V4 patchset.
But
it only works for clients requesting through devicetree, not from
platform
code or even sysfs.

One thing I can try is to dynamically change the channels the system
timer
and clocksource are using when the current ones are requested for PWM.
But
that sounds hardcore...

>> +
>> +
>> +Children nodes
>> +==========================================================
>> +
>> +
>> +PWM node:
>> +---------
>> +
>> +Required properties:
>> +
>> +- compatible: Must be one of:
>> + * ingenic,jz4740-pwm
>> + * ingenic,jz4725b-pwm
>> +- #pwm-cells: Should be 3. See ../pwm/pwm.txt for a description of
>> the cell
>> + format.
>> +- clocks: List of phandle & clock specifiers for the TCU clocks.
>> +- clock-names: List of name strings for the TCU clocks.
>> +
>> +
>> +Watchdog node:
>> +--------------
>> +
>> +Required properties:
>> +
>> +- compatible: Must be one of:
>> + * ingenic,jz4740-watchdog
>> + * ingenic,jz4780-watchdog
>> +- clocks: phandle to the RTC clock
>> +- clock-names: should be "rtc"
>> +
>> +
>> +OST node:
>> +---------
>> +
>> +Required properties:
>> +
>> +- compatible: Must be one of:
>> + * ingenic,jz4725b-ost
>> + * ingenic,jz4770-ost
>> +- clocks: phandle to the OST clock
>> +- clock-names: should be "ost"
>> +- interrupts : Specifies the interrupt the OST is connected to.
>> +
>> +
>> +Example
>> +==========================================================
>> +
>> +#include <dt-bindings/clock/jz4770-cgu.h>
>> +#include <dt-bindings/clock/ingenic,tcu.h>
>> +
>> +/ {
>> + tcu: timer@10002000 {
>> + compatible = "ingenic,jz4770-tcu";
>> + reg = <0x10002000 0x1000>;
>> + #address-cells = <1>;
>> + #size-cells = <1>;
>> + ranges = <0x0 0x10002000 0x1000>;
>> +
>> + #clock-cells = <1>;
>> +
>> + clocks = <&cgu JZ4770_CLK_RTC
>> + &cgu JZ4770_CLK_EXT
>> + &cgu JZ4770_CLK_PCLK
>> + &cgu JZ4770_CLK_EXT>;
>> + clock-names = "rtc", "ext", "pclk", "tcu";
>> +
>> + interrupt-controller;
>> + #interrupt-cells = <1>;
>> +
>> + interrupt-parent = <&intc>;
>> + interrupts = <27 26 25>;
>> +
>> + watchdog: watchdog@0 {
>> + compatible = "ingenic,jz4740-watchdog";
>> + reg = <0x0 0x10>;
>> +
>> + clocks = <&tcu TCU_CLK_WDT>;
>> + clock-names = "wdt";
>> + };
>> +
>> + pwm: pwm@10 {
>> + compatible = "ingenic,jz4740-pwm";
>> + reg = <0x10 0xff0>;
>> +
>> + #pwm-cells = <3>;
>> +
>> + clocks = <&tcu TCU_CLK_TIMER0
>> + &tcu TCU_CLK_TIMER1
>> + &tcu TCU_CLK_TIMER2
>> + &tcu TCU_CLK_TIMER3
>> + &tcu TCU_CLK_TIMER4
>> + &tcu TCU_CLK_TIMER5
>> + &tcu TCU_CLK_TIMER6
>> + &tcu TCU_CLK_TIMER7>;
>> + clock-names = "timer0", "timer1", "timer2", "timer3",
>> + "timer4", "timer5", "timer6", "timer7";
>> + };
>> +
>> + ost: timer@e0 {
>> + compatible = "ingenic,jz4770-ost";
>> + reg = <0xe0 0x20>;
>
> This is creating an overlapping region with PWM which should be
> avoided.
> Are timers and PWM the same h/w? Then there should be one node (or
> maybe
> you can do 1 node per channel if each channel is independent (has its
> own register range, clocks, interrupts, etc.
>
> Or the PWM node needs to exclude this region (by having 2 reg
> regions).

I will use two regions then.

>>
> +};
>>
> + };
>> +
>> + clocks = <&tcu TCU_CLK_OST>;
>> + clock-names = "ost";
>> +
>> + interrupts = <15>;
>> + };

Thanks,
-Paul Cercueil

\
 
 \ /
  Last update: 2018-07-31 00:03    [W:0.131 / U:1.912 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site