lkml.org 
[lkml]   [2018]   [Jul]   [3]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
Date
From
SubjectRe: [PATCH 2/3] mmc: sdhci: add quirk to prevent higher speed modes
On 02.07.2018 16:36, Ulf Hansson wrote:
> On 28 June 2018 at 10:13, Stefan Agner <stefan@agner.ch> wrote:
>> Some hosts are capable of running higher speed modes but do not
>> have the board support for it. Introduce a quirk which prevents
>> the stack from using modes running at 100MHz or faster.
>
> To cap the freq, use the DT property "max-frequency". To enable
> certain speed modes, use the corresponding speed mode binding. For
> example "sd-uhs-sdr*" and "mmc-hs200*".
> Documented in Documentation/devicetree/bindings/mmc/mmc.txt

I had bad experience with max-frequency: Some higher speed modes seem
not to work reliably if constraint to low frequencies. E.g. we had lots
of devices fail in practise with HS400@100MHz... So it is doing what it
should, but it just seems that higher speed modes do not necessarily run
well with lower frequencies...

So I'd rather prefer to limit speed modes as it is done right now.

>
> In case the sdhci cap register, doesn't reflect the board support
> properly, such that you may want to disable some speed modes, then you
> may benefit from using the DT properties "sdhci-caps*.
> Documented in Documentation/devicetree/bindings/mmc/sdhci.txt

Hm, yeah I guess something like

sdhci-caps-mask = /bits/ 64 <((SDHCI_SUPPORT_SDR104 |
SDHCI_SUPPORT_SDR50 | SDHCI_SUPPORT_DDR50) << 32)>

would come close.

But it does not restrict MMC modes such as HS200/HS400. There seem to be
no mmc-caps...


My aim is to replace the SDHCI_QUIRK2_NO_1_8_V fix, which does not
restrict modes correctly. Currently the driver checks whether >=100MHz
pinctrl settings are available, and if not uses the quirk to restrict
higher speed modes. Removing that would break device tree backward
compatibility...

We probably could do something like this:
if (!100mhzpinctrl) {
if (!sdhci-caps) {
/*
* If no 100MHz/200MHz pinctrl are available, SDHC caps should
be used to restrict
* modes. Falling back to old behavior...
*/
pr_warn(...)
host->quirks2 |= SDHCI_QUIRK2_NO_1_8_V;
}
}


--
Stefan

>
> Kind regards
> Uffe
>
>>
>> Signed-off-by: Stefan Agner <stefan@agner.ch>
>> ---
>> drivers/mmc/host/sdhci.c | 8 ++++++++
>> drivers/mmc/host/sdhci.h | 2 ++
>> 2 files changed, 10 insertions(+)
>>
>> diff --git a/drivers/mmc/host/sdhci.c b/drivers/mmc/host/sdhci.c
>> index 1c828e0e9905..8ac257dfaab3 100644
>> --- a/drivers/mmc/host/sdhci.c
>> +++ b/drivers/mmc/host/sdhci.c
>> @@ -3749,6 +3749,14 @@ int sdhci_setup_host(struct sdhci_host *host)
>> }
>> }
>>
>> + if (host->quirks2 & SDHCI_QUIRK2_NO_UHS_HS200_HS400) {
>> + host->caps1 &= ~(SDHCI_SUPPORT_SDR104 | SDHCI_SUPPORT_SDR50 |
>> + SDHCI_SUPPORT_DDR50);
>> +
>> + mmc->caps2 &= ~(MMC_CAP2_HSX00_1_8V | MMC_CAP2_HSX00_1_2V |
>> + MMC_CAP2_HS400_ES);
>> + }
>> +
>> if (host->quirks2 & SDHCI_QUIRK2_NO_1_8_V) {
>> host->caps1 &= ~(SDHCI_SUPPORT_SDR104 | SDHCI_SUPPORT_SDR50 |
>> SDHCI_SUPPORT_DDR50);
>> diff --git a/drivers/mmc/host/sdhci.h b/drivers/mmc/host/sdhci.h
>> index 23966f887da6..cb2433d6d61f 100644
>> --- a/drivers/mmc/host/sdhci.h
>> +++ b/drivers/mmc/host/sdhci.h
>> @@ -450,6 +450,8 @@ struct sdhci_host {
>> * obtainable timeout.
>> */
>> #define SDHCI_QUIRK2_DISABLE_HW_TIMEOUT (1<<17)
>> +/* Do not support any higher speeds (>50MHz) */
>> +#define SDHCI_QUIRK2_NO_UHS_HS200_HS400 (1<<18)
>>
>> int irq; /* Device IRQ */
>> void __iomem *ioaddr; /* Mapped address */
>> --
>> 2.18.0
>>

\
 
 \ /
  Last update: 2018-07-03 10:49    [W:0.093 / U:0.924 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site