lkml.org 
[lkml]   [2018]   [Jul]   [24]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH 3/3] arm64: dts: synaptics: add dtsi file for Synaptics AS370 SoC
Hi Rob,

On Fri, 20 Jul 2018 09:21:17 -0600 Rob Herring wrote:

> On Fri, Jul 13, 2018 at 05:26:26PM +0800, Jisheng Zhang wrote:
> > Add initial dtsi file to support Synaptics AS370 SoC with quad
> > Cortex-A53 CPUs.
> >
> > Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
> > ---
> > arch/arm64/boot/dts/synaptics/as370.dtsi | 177 +++++++++++++++++++++++
> > 1 file changed, 177 insertions(+)
> > create mode 100644 arch/arm64/boot/dts/synaptics/as370.dtsi
> >
> > diff --git a/arch/arm64/boot/dts/synaptics/as370.dtsi b/arch/arm64/boot/dts/synaptics/as370.dtsi
> > new file mode 100644
> > index 000000000000..20f3d658c566
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/synaptics/as370.dtsi
> > @@ -0,0 +1,177 @@
> > +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> > +/*
> > + * Copyright (C) 2018 Synaptics Incorporated
> > + *
> > + * Author: Jisheng Zhang <jszhang@kernel.org>
> > + */
> > +
> > +#include <dt-bindings/interrupt-controller/arm-gic.h>
> > +
> > +/ {
> > + compatible = "syna,as370";
> > + interrupt-parent = <&gic>;
> > + #address-cells = <2>;
> > + #size-cells = <2>;
> > +
> > + aliases {
> > + serial0 = &uart0;
>
> This normally goes in the board file. All boards will use this?

Yes. AFAIK, all boards will use uart0 as the serial console. But I could
move it to the board file.

>
> > + };
> > +
> > + psci {
> > + compatible = "arm,psci-1.0";
> > + method = "smc";
> > + };
> > +
> > + cpus {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + cpu0: cpu@0 {
> > + compatible = "arm,cortex-a53", "arm,armv8";
> > + device_type = "cpu";
> > + reg = <0x0>;
> > + enable-method = "psci";
> > + next-level-cache = <&l2>;
> > + cpu-idle-states = <&CPU_SLEEP_0>;
> > + };
> > +
> > + cpu1: cpu@1 {
> > + compatible = "arm,cortex-a53", "arm,armv8";
> > + device_type = "cpu";
> > + reg = <0x1>;
> > + enable-method = "psci";
> > + next-level-cache = <&l2>;
> > + cpu-idle-states = <&CPU_SLEEP_0>;
> > + };
> > +
> > + cpu2: cpu@2 {
> > + compatible = "arm,cortex-a53", "arm,armv8";
> > + device_type = "cpu";
> > + reg = <0x2>;
> > + enable-method = "psci";
> > + next-level-cache = <&l2>;
> > + cpu-idle-states = <&CPU_SLEEP_0>;
> > + };
> > +
> > + cpu3: cpu@3 {
> > + compatible = "arm,cortex-a53", "arm,armv8";
> > + device_type = "cpu";
> > + reg = <0x3>;
> > + enable-method = "psci";
> > + next-level-cache = <&l2>;
> > + cpu-idle-states = <&CPU_SLEEP_0>;
> > + };
> > +
> > + l2: cache {
> > + compatible = "cache";
>
> Why do you need this node? Doesn't define

If the l2 node is missing, I will get below warning:

[ 1.364795] Unable to detect cache hierarchy for CPU 0

reported by drivers/base/cacheinfo.c


>
> > + };
> > +
> > + idle-states {
> > + entry-method = "psci";
> > + CPU_SLEEP_0: cpu-sleep-0 {
> > + compatible = "arm,idle-state";
> > + local-timer-stop;
> > + arm,psci-suspend-param = <0x0010000>;
> > + entry-latency-us = <75>;
> > + exit-latency-us = <155>;
> > + min-residency-us = <1000>;
> > + };
> > + };
> > + };
> > +
> > + osc: osc {
> > + compatible = "fixed-clock";
> > + #clock-cells = <0>;
> > + clock-frequency = <25000000>;
> > + };
> > +
> > + pmu {
> > + compatible = "arm,cortex-a53-pmu";
> > + interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
> > + interrupt-affinity = <&cpu0>,
> > + <&cpu1>,
> > + <&cpu2>,
> > + <&cpu3>;
> > + };
> > +
> > + timer {
> > + compatible = "arm,armv8-timer";
> > + interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
> > + <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
> > + <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
> > + <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
> > + };
> > +
> > + soc@f7000000 {
> > + compatible = "simple-bus";
> > + #address-cells = <1>;
> > + #size-cells = <1>;
> > + ranges = <0 0 0xf7000000 0x1000000>;
> > +
> > + gic: interrupt-controller@901000 {
> > + compatible = "arm,gic-400";
> > + #interrupt-cells = <3>;
> > + interrupt-controller;
> > + reg = <0x901000 0x1000>,
> > + <0x902000 0x2000>,
> > + <0x904000 0x2000>,
> > + <0x906000 0x2000>;
> > + interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
> > + };
> > +
> > + apb@e80000 {
> > + compatible = "simple-bus";
> > + #address-cells = <1>;
> > + #size-cells = <1>;
> > + ranges = <0 0xe80000 0x10000>;
> > +
> > + uart0: uart@0c00 {
>
> serial@c00

will do in v2

Thanks a lot

\
 
 \ /
  Last update: 2018-07-24 08:01    [W:0.077 / U:0.404 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site