lkml.org 
[lkml]   [2018]   [Jul]   [20]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH V4 3/8] backlight: qcom-wled: Add new properties for PMI8998
From
Date
On 09/07/18 11:22, Kiran Gunda wrote:
> Update the bindings with the new properties used for
> PMI8998.
>
> Signed-off-by: Kiran Gunda <kgunda@codeaurora.org>

Acked-by: Daniel Thompson <daniel.thompson@linaro.org>


> ---
> Changes from V3:
> - Removed the default values.
> - Removed pmi8998 example.
>
> .../bindings/leds/backlight/qcom-wled.txt | 76 ++++++++++++++++++----
> 1 file changed, 62 insertions(+), 14 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/leds/backlight/qcom-wled.txt b/Documentation/devicetree/bindings/leds/backlight/qcom-wled.txt
> index 14f28f2..3f22ced 100644
> --- a/Documentation/devicetree/bindings/leds/backlight/qcom-wled.txt
> +++ b/Documentation/devicetree/bindings/leds/backlight/qcom-wled.txt
> @@ -20,8 +20,7 @@ platforms. The PMIC is connected to the host processor via SPMI bus.
> - default-brightness
> Usage: optional
> Value type: <u32>
> - Definition: brightness value on boot, value from: 0-4095
> - Default: 2048
> + Definition: brightness value on boot, value from: 0-4095.
>
> - label
> Usage: required
> @@ -48,20 +47,24 @@ platforms. The PMIC is connected to the host processor via SPMI bus.
> - qcom,current-limit
> Usage: optional
> Value type: <u32>
> - Definition: mA; per-string current limit
> - value: For pm8941: from 0 to 25 with 5 mA step
> - Default 20 mA.
> - For pmi8998: from 0 to 30 with 5 mA step
> - Default 25 mA.
> + Definition: mA; per-string current limit; value from 0 to 25 with
> + 1 mA step.
> + This property is supported only for pm8941.
> +
> +- qcom,current-limit-microamp
> + Usage: optional
> + Value type: <u32>
> + Definition: uA; per-string current limit; value from 0 to 30000 with
> + 2500 uA step.
>
> - qcom,current-boost-limit
> Usage: optional
> Value type: <u32>
> Definition: mA; boost current limit.
> For pm8941: one of: 105, 385, 525, 805, 980, 1260, 1400,
> - 1680. Default: 805 mA
> + 1680.
> For pmi8998: one of: 105, 280, 450, 620, 970, 1150, 1300,
> - 1500. Default: 970 mA
> + 1500.
>
> - qcom,switching-freq
> Usage: optional
> @@ -69,22 +72,66 @@ platforms. The PMIC is connected to the host processor via SPMI bus.
> Definition: kHz; switching frequency; one of: 600, 640, 685, 738,
> 800, 872, 960, 1066, 1200, 1371, 1600, 1920, 2400, 3200,
> 4800, 9600.
> - Default: for pm8941: 1600 kHz
> - for pmi8998: 800 kHz
>
> - qcom,ovp
> Usage: optional
> Value type: <u32>
> Definition: V; Over-voltage protection limit; one of:
> - 27, 29, 32, 35. default: 29V
> + 27, 29, 32, 35.
> This property is supported only for PM8941.
>
> +- qcom,ovp-millivolt
> + Usage: optional
> + Value type: <u32>
> + Definition: mV; Over-voltage protection limit;
> + For pmi8998: one of 18100, 19600, 29600, 31100
> + If this property is not specified for PM8941, it
> + falls back to "qcom,ovp" property.
> +
> - qcom,num-strings
> Usage: optional
> Value type: <u32>
> Definition: #; number of led strings attached;
> - value from 1 to 3. default: 2
> - This property is supported only for PM8941.
> + value: For PM8941 from 1 to 3.
> + For PMI8998 from 1 to 4.
> +
> +- interrupts
> + Usage: optional
> + Value type: <prop encoded array>
> + Definition: Interrupts associated with WLED. This should be
> + "short" and "ovp" interrupts. Interrupts can be
> + specified as per the encoding listed under
> + Documentation/devicetree/bindings/spmi/
> + qcom,spmi-pmic-arb.txt.
> +
> +- interrupt-names
> + Usage: optional
> + Value type: <string>
> + Definition: Interrupt names associated with the interrupts.
> + Must be "short" and "ovp". The short circuit detection
> + is not supported for PM8941.
> +
> +- qcom,enabled-strings
> + Usage: optional
> + Value tyoe: <u32 array>
> + Definition: Array of the WLED strings numbered from 0 to 3. Each
> + string of leds are operated individually. Specify the
> + list of strings used by the device. Any combination of
> + led strings can be used.
> +
> +- qcom,external-pfet
> + Usage: optional
> + Value type: <bool>
> + Definition: Specify if external PFET control for short circuit
> + protection is used. This property is supported only
> + for PMI8998.
> +
> +- qcom,auto-string-detection
> + Usage: optional
> + Value type: <bool>
> + Definition: Enables auto-detection of the WLED string configuration.
> + This feature is not supported for PM8941.
> +
>
> Example:
>
> @@ -99,4 +146,5 @@ pm8941-wled@d800 {
> qcom,switching-freq = <1600>;
> qcom,ovp = <29>;
> qcom,num-strings = <2>;
> + qcom,enabled-strings = <0x00 0x01>;
> };
>

\
 
 \ /
  Last update: 2018-07-20 15:15    [W:0.147 / U:2.312 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site