lkml.org 
[lkml]   [2018]   [Jul]   [17]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRe: [PATCH 1/2] Input: atmel_mxt_ts: Add support for optional regulators.
Date
On Sunday, July 15, 2018 10:25:47 AM CEST Dmitry Torokhov wrote:
> Hi Paweł,
>
> On Fri, Jul 13, 2018 at 08:30:07PM +0200, Paweł Chmiel wrote:
> > This patch adds optional regulators, which can be used to power
> > up touchscreen. After enabling regulators, we need to wait 150msec.
> > This value is taken from official driver.
> >
> > It was tested on Samsung Galaxy i9000 (based on Samsung S5PV210 SOC).
> >
> > Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
> > ---
> > drivers/input/touchscreen/atmel_mxt_ts.c | 45 ++++++++++++++++++++++++++++++++
> > 1 file changed, 45 insertions(+)
> >
> > diff --git a/drivers/input/touchscreen/atmel_mxt_ts.c b/drivers/input/touchscreen/atmel_mxt_ts.c
> > index 54fe190fd4bc..a7625ec8fb9f 100644
> > --- a/drivers/input/touchscreen/atmel_mxt_ts.c
> > +++ b/drivers/input/touchscreen/atmel_mxt_ts.c
> > @@ -27,6 +27,7 @@
> > #include <linux/interrupt.h>
> > #include <linux/of.h>
> > #include <linux/property.h>
> > +#include <linux/regulator/consumer.h>
> > #include <linux/slab.h>
> > #include <linux/gpio/consumer.h>
> > #include <linux/property.h>
> > @@ -198,6 +199,7 @@ enum t100_type {
> > #define MXT_RESET_INVALID_CHG 100 /* msec */
> > #define MXT_RESET_TIME 200 /* msec */
> > #define MXT_RESET_TIMEOUT 3000 /* msec */
> > +#define MXT_REGULATOR_DELAY 150 /* msec */
> > #define MXT_CRC_TIMEOUT 1000 /* msec */
> > #define MXT_FW_RESET_TIME 3000 /* msec */
> > #define MXT_FW_CHG_TIMEOUT 300 /* msec */
> > @@ -310,6 +312,8 @@ struct mxt_data {
> > struct t7_config t7_cfg;
> > struct mxt_dbg dbg;
> > struct gpio_desc *reset_gpio;
> > + struct regulator *vdd_reg;
> > + struct regulator *avdd_reg;
> >
> > /* Cached parameters from object table */
> > u16 T5_address;
> > @@ -3076,6 +3080,40 @@ static int mxt_probe(struct i2c_client *client, const struct i2c_device_id *id)
> > return error;
> > }
> >
> > + data->vdd_reg = devm_regulator_get_optional(&client->dev, "vdd");
> > + if (IS_ERR(data->vdd_reg)) {
> > + error = PTR_ERR(data->vdd_reg);
> > + dev_err(&client->dev, "Failed to get vdd regulator: %d\n",
> > + error);
> > + return error;
> > + }
> > +
> > + if (data->vdd_reg) {
> > + error = regulator_enable(data->vdd_reg);
> > + if (error) {
> > + dev_err(&client->dev, "Failed to enable vdd regulator: %d\n",
> > + error);
> > + return error;
> > + }
> > + }
> > +
> > + data->avdd_reg = devm_regulator_get_optional(&client->dev, "avdd");
> > + if (IS_ERR(data->avdd_reg)) {
> > + error = PTR_ERR(data->avdd_reg);
> > + dev_err(&client->dev, "Failed to get avdd regulator: %d\n",
> > + error);
> > + return error;
> > + }
> > +
> > + if (data->avdd_reg) {
>
> devm_regulator_get_optional() does not return NULL for regulators
> not present in device tree, but rather -ENOENT, so this code is not
> correct; neither is the simple IS_ERR() check above.
>
> Moreover, the optional regulators should be used when there is a part of
> IP block that can be optionally powered up, but the device can work
> (with limited functionality) even when it is powered down. They should
> not be used in cases when supplies are mandatory (such as vdd/avdd) but
> may not be exposed to the kernel by the firmware.
>
> Simply use devm_regulator_get() and rely on the fact that on fully
> constrained system you will get a dummy regulator.
>
> > + error = regulator_enable(data->avdd_reg);
> > + if (error) {
> > + dev_err(&client->dev, "Failed to enable avdd regulator: %d\n",
> > + error);
> > + return error;
> > + }
> > + }
> > +
> > error = devm_request_threaded_irq(&client->dev, client->irq,
> > NULL, mxt_interrupt, IRQF_ONESHOT,
> > client->name, data);
> > @@ -3086,6 +3124,9 @@ static int mxt_probe(struct i2c_client *client, const struct i2c_device_id *id)
> >
> > disable_irq(client->irq);
> >
> > + if (!IS_ERR(data->vdd_reg) || !IS_ERR(data->avdd_reg))
> > + msleep(MXT_REGULATOR_DELAY);
> > +
> > if (data->reset_gpio) {
>
> I think you should require that if regulators are exposed then reset
> gpio should also be present to ensure proper power up timings.

Thanks for comments. I'll prepare v2 version with those changes applied.
>
> > msleep(MXT_RESET_GPIO_TIME);
> > gpiod_set_value(data->reset_gpio, 1);
> > @@ -3116,6 +3157,10 @@ static int mxt_remove(struct i2c_client *client)
> > struct mxt_data *data = i2c_get_clientdata(client);
> >
> > disable_irq(data->irq);
> > + if (!IS_ERR(data->avdd_reg))
> > + regulator_disable(data->avdd_reg);
> > + if (!IS_ERR(data->vdd_reg))
> > + regulator_disable(data->vdd_reg);
> > sysfs_remove_group(&client->dev.kobj, &mxt_attr_group);
> > mxt_free_input_device(data);
> > mxt_free_object_table(data);
>
> Thanks.
>
>


\
 
 \ /
  Last update: 2018-07-17 18:08    [W:0.120 / U:1.336 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site