lkml.org 
[lkml]   [2018]   [Jun]   [29]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH 2/2] reset: uniphier: add USB3 controller reset control
Hi Philipp,
Thank you for your comments.

On Fri, 29 Jun 2018 11:55:24 +0200 <p.zabel@pengutronix.de> wrote:

> Hi Kunihiko,
>
> thank you for the patch. I just have a few small comments below:
>
> On Fri, 2018-06-29 at 17:11 +0900, Kunihiko Hayashi wrote:
> > Add reset lines for USB3 controller implemented in UniPhier SoCs.
> >
> > This reuses only the reset operations in reset-simple, because
> > the reset-simple doesn't handle any SoC-dependent clocks and resets.
> > This reset lines is included in the USB3 glue layer, and it's necessary
> > to enable clocks and deassert resets of the layer before using this
> > reset lines.
> >
> > Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
> > ---
> > drivers/reset/Kconfig | 10 ++
> > drivers/reset/Makefile | 1 +
> > drivers/reset/reset-uniphier-usb3.c | 183 ++++++++++++++++++++++++++++++++++++
> > 3 files changed, 194 insertions(+)
> > create mode 100644 drivers/reset/reset-uniphier-usb3.c
> >
> > diff --git a/drivers/reset/Kconfig b/drivers/reset/Kconfig
> > index c0b292b..851c9c3 100644
> > --- a/drivers/reset/Kconfig
> > +++ b/drivers/reset/Kconfig
> > @@ -138,6 +138,16 @@ config RESET_UNIPHIER
> > Say Y if you want to control reset signals provided by System Control
> > block, Media I/O block, Peripheral Block.
> >
> > +config RESET_UNIPHIER_USB3
> > + tristate "USB3 reset driver for UniPhier SoCs"
> > + depends on (ARCH_UNIPHIER || COMPILE_TEST) && OF
> > + default ARCH_UNIPHIER
> > + select RESET_SIMPLE
> > + help
> > + Support for USB3 reset controllers on UniPhier SoCs.
> > + Say Y if you want to control reset signals provided by
> > + USB3 controller block.
> > +
> > config RESET_ZYNQ
> > bool "ZYNQ Reset Driver" if COMPILE_TEST
> > default ARCH_ZYNQ
> > diff --git a/drivers/reset/Makefile b/drivers/reset/Makefile
> > index c1261dc..2638ac4 100644
> > --- a/drivers/reset/Makefile
> > +++ b/drivers/reset/Makefile
> > @@ -20,5 +20,6 @@ obj-$(CONFIG_RESET_SUNXI) += reset-sunxi.o
> > obj-$(CONFIG_RESET_TI_SCI) += reset-ti-sci.o
> > obj-$(CONFIG_RESET_TI_SYSCON) += reset-ti-syscon.o
> > obj-$(CONFIG_RESET_UNIPHIER) += reset-uniphier.o
> > +obj-$(CONFIG_RESET_UNIPHIER_USB3) += reset-uniphier-usb3.o
> > obj-$(CONFIG_RESET_ZYNQ) += reset-zynq.o
> >
> > diff --git a/drivers/reset/reset-uniphier-usb3.c b/drivers/reset/reset-uniphier-usb3.c
> > new file mode 100644
> > index 0000000..397e6c9
> > --- /dev/null
> > +++ b/drivers/reset/reset-uniphier-usb3.c
> > @@ -0,0 +1,183 @@
> > +// SPDX-License-Identifier: GPL-2.0
> > +/*
> > + * reset-uniphier-usb3.c - USB3 reset driver for UniPhier
> > + * Copyright 2018 Socionext Inc.
> > + * Author: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
> > + */
> > +
> > +#include <linux/clk.h>
> > +#include <linux/module.h>
> > +#include <linux/of_device.h>
> > +#include <linux/platform_device.h>
> > +#include <linux/reset.h>
> > +
> > +#include "reset-simple.h"
> > +
> > +#define MAX_CLKS 2
> > +#define MAX_RSTS 2
> > +
> > +struct uniphier_usb3_reset_soc_data {
> > + const char *clock_names[MAX_CLKS];
> > + const char *reset_names[MAX_RSTS];
> > +};
> > +
> > +struct uniphier_usb3_reset_priv {
>
> I'd embed a struct reset_simple_data here ...
>
> > + int nclks;
> > + struct clk *clk[MAX_CLKS];
> > + int nrsts;
> > + struct reset_control *rst[MAX_RSTS];
> > + const struct uniphier_usb3_reset_soc_data *data;
> > +};
> > +
> > +static int uniphier_usb3_reset_probe(struct platform_device *pdev)
> > +{
> > + struct device *dev = &pdev->dev;
> > + struct uniphier_usb3_reset_priv *priv;
> > + struct reset_simple_data *rst_data;
> > + struct resource *res;
> > + resource_size_t size;
> > + const char *name;
> > + int i, ret, nc, nr;
> > +
> > + priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
> > + if (!priv)
> > + return -ENOMEM;
> > +
> > + priv->data = of_device_get_match_data(dev);
> > + if (WARN_ON(!priv->data))
> > + return -EINVAL;
> > +
> > + rst_data = devm_kzalloc(dev, sizeof(*rst_data), GFP_KERNEL);
> > + if (!rst_data)
> > + return -ENOMEM;
>
> ... that way there's no need for two separate allocations.

Indeed. I'll embed reset_simple_data in uniphier_usb3_reset_priv,
and remove this.

> > +
> > + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> > + size = resource_size(res);
> > + rst_data->membase = devm_ioremap_resource(dev, res);
> > + if (IS_ERR(rst_data->membase))
> > + return PTR_ERR(rst_data->membase);
> > +
> > + for (i = 0; i < MAX_CLKS; i++) {
> > + name = priv->data->clock_names[i];
> > + if (!name)
> > + break;
> > + priv->clk[i] = devm_clk_get(dev, name);
> > + if (IS_ERR(priv->clk[i]))
> > + return PTR_ERR(priv->clk[i]);
> > + priv->nclks++;
> > + }
> > +
> > + for (i = 0; i < MAX_RSTS; i++) {
> > + name = priv->data->reset_names[i];
> > + if (!name)
> > + break;
> > + priv->rst[i] = devm_reset_control_get_shared(dev, name);
> > + if (IS_ERR(priv->rst[i]))
> > + return PTR_ERR(priv->rst[i]);
> > + priv->nrsts++;
> > + }
> > +
> > + for (nc = 0; nc < priv->nclks; nc++) {
> > + ret = clk_prepare_enable(priv->clk[nc]);
> > + if (ret)
> > + goto out_clk_disable;
> > + }
> > +
> > + for (nr = 0; nr < priv->nrsts; nr++) {
> > + ret = reset_control_deassert(priv->rst[nr]);
> > + if (ret)
> > + goto out_rst_assert;
> > + }
>
> Have you seen the clk_bulk_* APIs? Those could possibly simplify the
> code a bit.

Okay. I'll try to apply it.

> Unfortunately we don't have the equivalent reset bulk API.

Yes. And although the reset array API can get multiple resets,
it can't specify each reset with its name.

> > +
> > + spin_lock_init(&rst_data->lock);
> > + rst_data->rcdev.owner = THIS_MODULE;
> > + rst_data->rcdev.nr_resets = size * BITS_PER_BYTE;
> > + rst_data->rcdev.ops = &reset_simple_ops;
> > + rst_data->rcdev.of_node = dev->of_node;
> > + rst_data->active_low = true;
> > +
> > + platform_set_drvdata(pdev, priv);
> > +
> > + ret = devm_reset_controller_register(dev, &rst_data->rcdev);
> > + if (ret)
> > + goto out_rst_assert;
> > +
> > + return 0;
> > +
> > +out_rst_assert:
> > + while (nr--)
> > + reset_control_assert(priv->rst[nr]);
> > +out_clk_disable:
> > + while (nc--)
> > + clk_disable_unprepare(priv->clk[nc]);
> > +
> > + return ret;
> > +}
> > +
> > +static int uniphier_usb3_reset_remove(struct platform_device *pdev)
> > +{
> > + struct uniphier_usb3_reset_priv *priv = platform_get_drvdata(pdev);
> > + int i;
> > +
> > + for (i = 0; i < priv->nrsts; i++)
> > + reset_control_assert(priv->rst[i]);
> > + for (i = 0; i < priv->nclks; i++)
> > + clk_disable_unprepare(priv->clk[i]);
> > +
> > + return 0;
> > +}
> > +
> > +static const struct uniphier_usb3_reset_soc_data uniphier_pro4_data = {
> > + .clock_names = { "gio", "link", },
> > + .reset_names = { "gio", "link", },
> > +};
> > +
> > +static const struct uniphier_usb3_reset_soc_data uniphier_pxs2_data = {
> > + .clock_names = { "link", },
> > + .reset_names = { "link", },
> > +};
> > +
> > +static const struct uniphier_usb3_reset_soc_data uniphier_ld20_data = {
> > + .clock_names = { "link", },
> > + .reset_names = { "link", },
> > +};
> > +
> > +static const struct uniphier_usb3_reset_soc_data uniphier_pxs3_data = {
> > + .clock_names = { "link", },
> > + .reset_names = { "link", },
> > +};
>
> Could you reuse the same SoC data for pxs2, ld20 and pxs3?

Sure, I'll rewrite it.

Thank you,

> > +static const struct of_device_id uniphier_usb3_reset_match[] = {
> > + {
> > + .compatible = "socionext,uniphier-pro4-usb3-reset",
> > + .data = &uniphier_pro4_data,
> > + },
> > + {
> > + .compatible = "socionext,uniphier-pxs2-usb3-reset",
> > + .data = &uniphier_pxs2_data,
> > + },
> > + {
> > + .compatible = "socionext,uniphier-ld20-usb3-reset",
> > + .data = &uniphier_ld20_data,
> > + },
> > + {
> > + .compatible = "socionext,uniphier-pxs3-usb3-reset",
> > + .data = &uniphier_pxs3_data,
> > + },
> > + { /* Sentinel */ }
> > +};
> > +MODULE_DEVICE_TABLE(of, uniphier_usb3_reset_match);
> > +
> > +static struct platform_driver uniphier_usb3_reset_driver = {
> > + .probe = uniphier_usb3_reset_probe,
> > + .remove = uniphier_usb3_reset_remove,
> > + .driver = {
> > + .name = "uniphier-usb3-reset",
> > + .of_match_table = uniphier_usb3_reset_match,
> > + },
> > +};
> > +module_platform_driver(uniphier_usb3_reset_driver);
> > +
> > +MODULE_AUTHOR("Kunihiko Hayashi <hayashi.kunihiko@socionext.com>");
> > +MODULE_DESCRIPTION("UniPhier USB3 Reset Driver");
> > +MODULE_LICENSE("GPL");
>
> regards
> Philipp

---
Best Regards,
Kunihiko Hayashi


\
 
 \ /
  Last update: 2018-06-29 12:54    [W:0.051 / U:6.912 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site