lkml.org 
[lkml]   [2018]   [Jun]   [18]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v2 07/10] dt-bindings: tc358754: add DT bindings
From
Date

On 05/30/2018 02:36 PM, Laurent Pinchart wrote:
> Hi Maciej,
>
> On Wednesday, 30 May 2018 15:15:58 EEST Maciej Purski wrote:
>> From: Andrzej Hajda <a.hajda@samsung.com>
>>
>> The patch adds bindings to Toshiba DSI/LVDS bridge TC358764.
>> Bindings describe power supplies, reset gpio and video interfaces.
>>
>> Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
>> Signed-off-by: Maciej Purski <m.purski@samsung.com>
>> ---
>> .../bindings/display/bridge/toshiba,tc358764.txt | 37 +++++++++++++++++++
>> 1 file changed, 37 insertions(+)
>> create mode 100644
>> Documentation/devicetree/bindings/display/bridge/toshiba,tc358764.txt
>>
>> diff --git
>> a/Documentation/devicetree/bindings/display/bridge/toshiba,tc358764.txt
>> b/Documentation/devicetree/bindings/display/bridge/toshiba,tc358764.txt new
>> file mode 100644
>> index 0000000..6eda14f
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/display/bridge/toshiba,tc358764.txt
>> @@ -0,0 +1,37 @@
>> +TC358764 MIPI-DSI to LVDS panel bridge
>> +
>> +Required properties:
>> + - compatible: "toshiba,tc358764"
>> + - reg: the virtual channel number of a DSI peripheral
>> + - vddc-supply: core voltage supply, 1.2V
>> + - vddio-supply: I/O voltage supply, 1.8V or 3.3V
>> + - vddlvds-supply: LVDS1/2 voltage supply, 3.3V
>> + - reset-gpios: a GPIO spec for the reset pin
>> +
>> +The device node can contain zero to two 'port' child nodes, each with one
>> +child 'endpoint' node, according to the bindings defined in [1].
>> +The following are properties specific to those nodes.
>> +
>> +port:
>> + - reg: (required) can be 0 for DSI port or 1 for LVDS port;
>> +
>> +[1]: Documentation/devicetree/bindings/media/video-interfaces.txt
>
> Could you please take the comments I made on v1 into account when you'll post
> v3 ?
>

For now I'm going to stick with the old convention and make port 0 optional,
when the bridge is a DSI child and LVDS port 1 mandatory.

The current policy does not seem to have been changed. There's a quiet new binding,
which follows the old convention:
Documentation/devicetree/bindings/connector/usb-connector.txt

If you can find an example of new bindings, which follow your convention and you
convince Rob, then I'll be completely okay with it and I'll change it the way
you propose.


>> +Example:
>> +
>> + bridge@0 {
>> + reg = <0>;
>> + compatible = "toshiba,tc358764";
>> + vddc-supply = <&vcc_1v2_reg>;
>> + vddio-supply = <&vcc_1v8_reg>;
>> + vddlvds-supply = <&vcc_3v3_reg>;
>> + reset-gpios = <&gpd1 6 GPIO_ACTIVE_LOW>;
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + port@1 {
>> + reg = <1>;
>> + lvds_ep: endpoint {
>> + remote-endpoint = <&panel_ep>;
>> + };
>> + };
>> + };
>
>

Best regards,

Maciej Purski

\
 
 \ /
  Last update: 2018-06-18 13:08    [W:0.037 / U:0.076 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site