lkml.org 
[lkml]   [2018]   [May]   [7]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v4 3/3] ARM: dts: sun8i: h3: Add SY8106A regulator to Orange Pi PC
Date
From: Ondrej Jirman <megous@megous.com>

Add SY8106A regulator to r_i2c bus and enable the r_i2c bus on
Orange Pi PC, then set the power supply of the ARM cores to this
regulator, in order to enable DVFS.

Signed-off-by: Ondrej Jirman <megous@megous.com>
[Icenowy: Enable DVFS in this patch, slight changes and change commit
message]
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
[wens@csie.org: Rename regulator label]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
---
No changes in v4.

Changes in v3:
- Renamed regulator label (by Chen-Yu Tsai).
- Added the fixed mode voltage number.

Changes in v2:
- Reduce maximum voltage to 1.3V.
- Slightly changed the comment at 1.0V minimum voltage for taking BSP
DVFS table instead of Armbian one.

arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts | 28 ++++++++++++++++++++++
1 file changed, 28 insertions(+)

diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts b/arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts
index cea4d647ecbf..46240334128f 100644
--- a/arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts
+++ b/arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts
@@ -113,6 +113,10 @@
status = "okay";
};

+&cpu0 {
+ cpu-supply = <&reg_vdd_cpux>;
+};
+
&ehci0 {
status = "okay";
};
@@ -182,6 +186,30 @@
};
};

+&r_i2c {
+ status = "okay";
+
+ reg_vdd_cpux: regulator@65 {
+ compatible = "silergy,sy8106a";
+ reg = <0x65>;
+ regulator-name = "vdd-cpux";
+ silergy,fixed-microvolt = <1200000>;
+ /*
+ * The datasheet uses 1.1V as the minimum value of VDD-CPUX,
+ * however both the Armbian DVFS table and the official one
+ * have operating points with voltage under 1.1V, and both
+ * DVFS table are known to work properly at the lowest
+ * operating point.
+ *
+ * Use 1.0V as the minimum voltage instead.
+ */
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+};
+
&r_pio {
leds_r_opc: led_pins {
pins = "PL10";
--
2.17.0
\
 
 \ /
  Last update: 2018-05-07 14:33    [W:0.056 / U:7.388 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site