lkml.org 
[lkml]   [2018]   [May]   [5]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH V6 4/7] ARM: dts: imx6sx-sabreauto: add fec support
Date
Add FEC support on i.MX6SX Sabre Auto board.

Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
---
changes since V5:
use "gpios" instead of "enable-gpio".
arch/arm/boot/dts/imx6sx-sabreauto.dts | 80 ++++++++++++++++++++++++++++++++++
1 file changed, 80 insertions(+)

diff --git a/arch/arm/boot/dts/imx6sx-sabreauto.dts b/arch/arm/boot/dts/imx6sx-sabreauto.dts
index 4d41b4d..7dda741 100644
--- a/arch/arm/boot/dts/imx6sx-sabreauto.dts
+++ b/arch/arm/boot/dts/imx6sx-sabreauto.dts
@@ -18,6 +18,17 @@
reg = <0x80000000 0x80000000>;
};

+ reg_fec: fec_io_supply {
+ compatible = "regulator-gpio";
+ regulator-name = "1.8V_1.5V_FEC";
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1800000>;
+ states = <1500000 0x0 1800000 0x1>;
+ gpios = <&max7322 0 GPIO_ACTIVE_HIGH>;
+ vin-supply = <&sw2_reg>;
+ enable-active-high;
+ };
+
vcc_sd3: regulator-vcc-sd3 {
compatible = "regulator-fixed";
pinctrl-names = "default";
@@ -34,6 +45,39 @@
clock-frequency = <24576000>;
};

+&fec1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet1>;
+ phy-mode = "rgmii";
+ phy-handle = <&ethphy1>;
+ fsl,magic-packet;
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethphy0: ethernet-phy@0 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <0>;
+ };
+
+ ethphy1: ethernet-phy@1 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <1>;
+ };
+ };
+};
+
+&fec2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet2>;
+ phy-mode = "rgmii";
+ phy-handle = <&ethphy0>;
+ fsl,magic-packet;
+ status = "okay";
+};
+
&uart1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart1>;
@@ -66,6 +110,42 @@
};

&iomuxc {
+ pinctrl_enet1: enet1grp {
+ fsl,pins = <
+ MX6SX_PAD_ENET1_MDIO__ENET1_MDIO 0xa0b1
+ MX6SX_PAD_ENET1_MDC__ENET1_MDC 0xa0b1
+ MX6SX_PAD_RGMII1_TXC__ENET1_RGMII_TXC 0xa0b9
+ MX6SX_PAD_RGMII1_TD0__ENET1_TX_DATA_0 0xa0b1
+ MX6SX_PAD_RGMII1_TD1__ENET1_TX_DATA_1 0xa0b1
+ MX6SX_PAD_RGMII1_TD2__ENET1_TX_DATA_2 0xa0b1
+ MX6SX_PAD_RGMII1_TD3__ENET1_TX_DATA_3 0xa0b1
+ MX6SX_PAD_RGMII1_TX_CTL__ENET1_TX_EN 0xa0b1
+ MX6SX_PAD_RGMII1_RXC__ENET1_RX_CLK 0x3081
+ MX6SX_PAD_RGMII1_RD0__ENET1_RX_DATA_0 0x3081
+ MX6SX_PAD_RGMII1_RD1__ENET1_RX_DATA_1 0x3081
+ MX6SX_PAD_RGMII1_RD2__ENET1_RX_DATA_2 0x3081
+ MX6SX_PAD_RGMII1_RD3__ENET1_RX_DATA_3 0x3081
+ MX6SX_PAD_RGMII1_RX_CTL__ENET1_RX_EN 0x3081
+ >;
+ };
+
+ pinctrl_enet2: enet2grp {
+ fsl,pins = <
+ MX6SX_PAD_RGMII2_TXC__ENET2_RGMII_TXC 0xa0b9
+ MX6SX_PAD_RGMII2_TD0__ENET2_TX_DATA_0 0xa0b1
+ MX6SX_PAD_RGMII2_TD1__ENET2_TX_DATA_1 0xa0b1
+ MX6SX_PAD_RGMII2_TD2__ENET2_TX_DATA_2 0xa0b1
+ MX6SX_PAD_RGMII2_TD3__ENET2_TX_DATA_3 0xa0b1
+ MX6SX_PAD_RGMII2_TX_CTL__ENET2_TX_EN 0xa0b1
+ MX6SX_PAD_RGMII2_RXC__ENET2_RX_CLK 0x3081
+ MX6SX_PAD_RGMII2_RD0__ENET2_RX_DATA_0 0x3081
+ MX6SX_PAD_RGMII2_RD1__ENET2_RX_DATA_1 0x3081
+ MX6SX_PAD_RGMII2_RD2__ENET2_RX_DATA_2 0x3081
+ MX6SX_PAD_RGMII2_RD3__ENET2_RX_DATA_3 0x3081
+ MX6SX_PAD_RGMII2_RX_CTL__ENET2_RX_EN 0x3081
+ >;
+ };
+
pinctrl_i2c2: i2c2grp {
fsl,pins = <
MX6SX_PAD_GPIO1_IO03__I2C2_SDA 0x4001b8b1
--
2.7.4
\
 
 \ /
  Last update: 2018-05-05 10:34    [W:0.105 / U:1.020 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site