[lkml]   [2018]   [May]   [30]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
Messages in this thread
Subject[PATCH v4 0/6] mfd/regulator/clk: bd71837: ROHM BD71837 PMIC driver
Patch series adding support for ROHM BD71837 PMIC.

BD71837 is a programmable Power Management IC for powering single-core,
dual-core, and quad-core SoC’s such as NXP-i.MX 8M. It is optimized for
low BOM cost and compact solution footprint. It integrates 8 buck
regulators and 7 LDO’s to provide all the power rails required by the
SoC and the commonly used peripherals.

The driver aims to not limit the usage of PMIC. Thus the buck and LDO
naming is generic and not tied to any specific purposes. However there
is following limitations which make it mostly suitable for use cases
where the processor where PMIC driver is running is powered by the PMIC:

- The PMIC is not re-initialized if it resets. PMIC may reset as a
result of voltage monitoring (over/under voltage) or due to reset
request. Driver is only initializing PMIC at probe. This is not
problem as long as processor controlling PMIC is powered by PMIC.

- The PMIC internal state machine is ignored by driver. Driver assumes
the PMIC is wired so that it is always in "run" state when controlled
by the driver.

Changelog v4
- remove mutex from regulator state check as core prevents simultaneous
- allow voltage change for bucks 1 to 4 when regulator is enabled
- fix indentiation problems
- properly correct SPDX comments

Changelog v3
- kill unused variable
- kill unused definitions

Changelog v2
Based on feedback from Mark Brown
- Squashed code and buildfile changes to same patch
- Fixed some styling issues
- Changed SPDX comments to CPP style
- Error out if voltage is changed when regulator is enabled instead of
Disabling the regulator for duration of change
- Use devm_regulator_register
- Remove compatible usage from regulators - use parent dev for config
- Add a note about using regulator-boot-on for BUCK6 and 7
- fixed warnings from kbuild test robot

patch 1:
MFD driver and definitions bringing interrupt support and
enabling clk and regulator subsystems.
Patches 2, 3 and 4:
device tree binding documents.
Patch 5:
clock subsystem and support for gated clock.
Patch 6:
regulator driver supporting 8 bucks and 7 LDOs.

This patch series is based on for-mfd-next


Matti Vaittinen (6):
mfd: bd71837: mfd driver for ROHM BD71837 PMIC
mfd: bd71837: Devicetree bindings for ROHM BD71837 PMIC
regulator: bd71837: Devicetree bindings for BD71837 regulators
clk: bd71837: Devicetree bindings for ROHM BD71837 PMIC
clk: bd71837: Add driver for BD71837 PMIC clock
regulator: bd71837: BD71837 PMIC regulator driver

.../bindings/clock/rohm,bd71837-clock.txt | 37 ++
.../devicetree/bindings/mfd/rohm,bd71837-pmic.txt | 52 ++
.../bindings/regulator/rohm,bd71837-regulator.txt | 126 ++++
drivers/clk/Kconfig | 9 +
drivers/clk/Makefile | 1 +
drivers/clk/clk-bd71837.c | 151 +++++
drivers/mfd/Kconfig | 13 +
drivers/mfd/Makefile | 1 +
drivers/mfd/bd71837.c | 222 +++++++
drivers/regulator/Kconfig | 11 +
drivers/regulator/Makefile | 1 +
drivers/regulator/bd71837-regulator.c | 640 +++++++++++++++++++++
include/linux/mfd/bd71837.h | 288 ++++++++++
13 files changed, 1552 insertions(+)
create mode 100644 Documentation/devicetree/bindings/clock/rohm,bd71837-clock.txt
create mode 100644 Documentation/devicetree/bindings/mfd/rohm,bd71837-pmic.txt
create mode 100644 Documentation/devicetree/bindings/regulator/rohm,bd71837-regulator.txt
create mode 100644 drivers/clk/clk-bd71837.c
create mode 100644 drivers/mfd/bd71837.c
create mode 100644 drivers/regulator/bd71837-regulator.c
create mode 100644 include/linux/mfd/bd71837.h


 \ /
  Last update: 2018-05-30 10:41    [W:0.140 / U:1.336 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site