lkml.org 
[lkml]   [2018]   [May]   [27]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v2 2/6] mtd: rawnand: tegra: add devicetree binding
Hi Stefan,

On Sun, 27 May 2018 23:54:38 +0200, Stefan Agner <stefan@agner.ch>
wrote:

> From: Lucas Stach <dev@lynxeye.de>
>
> This adds the devicetree binding for the Tegra 2 NAND flash
> controller.
>
> Signed-off-by: Lucas Stach <dev@lynxeye.de>
> Signed-off-by: Stefan Agner <stefan@agner.ch>
> ---
> .../bindings/mtd/nvidia,tegra20-nand.txt | 62 +++++++++++++++++++
> 1 file changed, 62 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/mtd/nvidia,tegra20-nand.txt
>
> diff --git a/Documentation/devicetree/bindings/mtd/nvidia,tegra20-nand.txt b/Documentation/devicetree/bindings/mtd/nvidia,tegra20-nand.txt
> new file mode 100644
> index 000000000000..49e472af1b39
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/mtd/nvidia,tegra20-nand.txt
> @@ -0,0 +1,62 @@
> +NVIDIA Tegra NAND Flash controller
> +
> +Required properties:
> +- compatible: Must be one of:

Nitpick: just put the compatible here as there is only one?

> + - "nvidia,tegra20-nand"
> +- reg: MMIO address range
> +- interrupts: interrupt output of the NFC controller
> +- clocks: Must contain an entry for each entry in clock-names.
> + See ../clocks/clock-bindings.txt for details.
> +- clock-names: Must include the following entries:
> + - nand
> +- resets: Must contain an entry for each entry in reset-names.
> + See ../reset/reset.txt for details.
> +- reset-names: Must include the following entries:
> + - nand
> +
> +Optional children nodes:
> +Individual NAND chips are children of the NAND controller node. Currently
> +only one NAND chip supported.
> +
> +Required children node properties:
> +- reg: An integer ranging from 1 to 6 representing the CS line to use.

From 1? It usually starts at 0.

> +
> +Optional children node properties:
> +- nand-ecc-mode: String, operation mode of the NAND ecc mode. "hw" by default
> +- nand-ecc-algo: string, algorithm of NAND ECC.
> + Supported values are: "rs", "bch".
> +- nand-bus-width : 8 or 16 bus width if not present 8
> +- nand-on-flash-bbt: boolean to enable on flash bbt option if not present false
> +- nand-ecc-strength: integer representing the number of bits to correct
> + per ECC step. Supported strength using HW ECC modes are:
> + - RS: 4, 6, 8
> + - BCH: 4, 8, 14, 16
> +- nand-ecc-step-size: integer representing the number of data bytes
> + that are covered by a single ECC step. Must be 512.

Please don't re-explain nand generic DT properties, point to nand.txt
instead.

> +- wp-gpios: GPIO specifier for the write protect pin.
> +
> +Optional child node of NAND chip nodes:
> +Partitions: see partition.txt
> +
> + Example:
> + nand@70008000 {
> + compatible = "nvidia,tegra20-nand";
> + reg = <0x70008000 0x100>;
> + interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&tegra_car TEGRA20_CLK_NDFLASH>;
> + clock-names = "nand";
> + resets = <&tegra_car 13>;
> + reset-names = "nand";
> +
> + nand-chip@0 {
> + reg = <0>;
> + #address-cells = <1>;
> + #size-cells = <1>;
> + nand-bus-width = <8>;
> + nand-on-flash-bbt;
> + nand-ecc-algo = "bch";
> + nand-ecc-step-size = <512>;

In the driver you only refer to step sizes of 512 B, you can remove the
property from the bindings.

> + nand-ecc-strength = <8>;
> + wp-gpios = <&gpio TEGRA_GPIO(S, 0) GPIO_ACTIVE_LOW>;
> + };
> + };



--
Miquel Raynal, Bootlin (formerly Free Electrons)
Embedded Linux and Kernel engineering
https://bootlin.com

\
 
 \ /
  Last update: 2018-05-28 00:24    [W:0.068 / U:2.560 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site