lkml.org 
[lkml]   [2018]   [May]   [23]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: B53 DSA switch problem on Banana Pi-R1 on Fedora 26
From
Date
On 23.05.2018 17:50, Florian Fainelli wrote:
>
> On 05/23/2018 08:28 AM, Florian Fainelli wrote:
>>
>> On 05/22/2018 09:49 PM, Gerhard Wiesinger wrote:
>>> On 22.05.2018 22:42, Florian Fainelli wrote:
>>>> On 05/22/2018 01:16 PM, Andrew Lunn wrote:
>>>>>> Planned network structure will be as with 4.7.x kernels:
>>>>>>
>>>>>> br0 <=> eth0.101 <=> eth0 (vlan 101 tagged) <=> lan 1-lan4 (vlan 101
>>>>>> untagged pvid)
>>>>>>
>>>>>> br1 <=> eth0.102 <=> eth0 (vlan 102 tagged) <=> wan (vlan 102
>>>>>> untagged pvid)
>>>>> Do you even need these vlans?
>>>> Yes, remember, b53 does not currently turn on Broadcom tags, so the only
>>>> way to segregate traffic is to have VLANs for that.
>>>>
>>>>> Are you doing this for port separation? To keep lan1-4 traffic
>>>>> separate from wan? DSA does that by default, no vlan needed.
>>>>>
>>>>> So you can just do
>>>>>
>>>>> ip link add name br0 type bridge
>>>>> ip link set dev br0 up
>>>>> ip link set dev lan1 master br0
>>>>> ip link set dev lan2 master br0
>>>>> ip link set dev lan3 master br0
>>>>> ip link set dev lan4 master br0
>>>>>
>>>>> and use interface wan directly, no bridge needed.
>>>> That would work once Broadcom tags are turned on which requires turning
>>>> on managed mode, which requires work that I have not been able to get
>>>> done :)
>>> Setup with swconfig:
>>>
>>> #!/usr/bin/bash
>>>
>>>
>>> INTERFACE=eth0
>>>
>>> # Delete all IP addresses and get link up
>>> ip addr flush dev ${INTERFACE}
>>> ip link set ${INTERFACE} up
>>>
>>> # Lamobo R1 aka BPi R1 Routerboard
>>> #
>>> # Speaker | LAN1 | LAN2 | LAN3 | LAN4 || LAN5 | HDMI
>>> # SW-Port |  P2  |  P1  |  P0  |  P4  ||  P3  |
>>> # VLAN    |  11  |  12  |  13  |  14  ||ALL(t)|
>>> #
>>> # Switch-Port P8 - ALL(t) boards internal CPU Port
>>>
>>> # Setup switch
>>> swconfig dev ${INTERFACE} set reset 1
>>> swconfig dev ${INTERFACE} set enable_vlan 1
>>> swconfig dev ${INTERFACE} vlan 101 set ports '3 8t'
>>> swconfig dev ${INTERFACE} vlan 102 set ports '4 0 1 2 8t'
>>> swconfig dev ${INTERFACE} set apply 1
>>>
>>> How to achieve this setup CURRENTLY with DSA?
>> Your first email had the right programming sequence, but you did not
>> answer whether you have CONFIG_BRIDGE_VLAN_FILTERING enabled or not,
>> which is likely your problem.
> Here are some reference configurations that should work:
>
> https://github.com/armbian/build/issues/511#issuecomment-320473246

I know, some comments are from me but none of them worked, therefore on
LKML :-)

/boot/config-4.16.7-100.fc26.armv7hl:CONFIG_BRIDGE_VLAN_FILTERING=y

so this can't be the issue, any further ideas?

On my 2nd Banana Pi-R1 still on Fedora 25 with kernel
4.12.8-200.fc25.armv7hl the commands still work well, but I wanted to
test the upgrade on another one.

/boot/config-4.12.8-200.fc25.armv7hl:CONFIG_BRIDGE_VLAN_FILTERING=y

Thnx.

Ciao,

Gerhard

\
 
 \ /
  Last update: 2018-05-23 19:30    [W:0.072 / U:1.964 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site