lkml.org 
[lkml]   [2018]   [May]   [21]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[v4 01/11] dt-bindings: Add a document of PECI subsystem
Date
This commit adds a document of generic PECI bus, adapter and client
driver.

Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Haiyue Wang <haiyue.wang@linux.intel.com>
Reviewed-by: James Feist <james.feist@linux.intel.com>
Reviewed-by: Vernon Mauery <vernon.mauery@linux.intel.com>
Cc: Andrew Jeffery <andrew@aj.id.au>
Cc: Joel Stanley <joel@jms.id.au>
---
.../devicetree/bindings/peci/peci.txt | 59 +++++++++++++++++++
1 file changed, 59 insertions(+)
create mode 100644 Documentation/devicetree/bindings/peci/peci.txt

diff --git a/Documentation/devicetree/bindings/peci/peci.txt b/Documentation/devicetree/bindings/peci/peci.txt
new file mode 100644
index 000000000000..72fc8ddd6a55
--- /dev/null
+++ b/Documentation/devicetree/bindings/peci/peci.txt
@@ -0,0 +1,59 @@
+Generic device tree configuration for PECI buses
+================================================
+
+Required properties:
+- compatible : Should be "simple-bus".
+- #address-cells : Should be present if the device has sub-nodes.
+- #size-cells : Should be present if the device has sub-nodes.
+- ranges : Should contain PECI controller registers ranges.
+
+Example:
+ peci: peci@10000000 {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0x0 0x10000000 0x1000>;
+ };
+
+Generic device tree configuration for PECI adapters
+===================================================
+
+Required properties:
+- #address-cells : Should be <1>. Read more about client addresses below.
+- #size-cells : Should be <0>. Read more about client addresses below.
+
+The cells properties above define that an address of CPU clients of a PECI bus
+are described by a single value.
+
+Example:
+ peci0: peci-bus@0 {
+ compatible = "soc,soc-peci";
+ reg = <0x0 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+Generic device tree configuration for PECI clients
+==================================================
+
+Required properties:
+- compatible : Should contain name of PECI client.
+- reg : Should contain address of a client CPU. Address range of CPU
+ clients is starting from 0x30 based on PECI specification.
+
+Example:
+ peci-bus@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ < more properties >
+
+ function@30 {
+ compatible = "device,function";
+ reg = <0x30>;
+ };
+
+ function@31 {
+ compatible = "device,function";
+ reg = <0x31>;
+ };
+ };
--
2.17.0
\
 
 \ /
  Last update: 2018-05-21 21:58    [W:0.019 / U:0.952 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site