lkml.org 
[lkml]   [2018]   [May]   [18]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v3 4/6] dt-bindings: add binding for at91-usart in spi mode
On Fri, May 11, 2018 at 01:38:20PM +0300, Radu Pirea wrote:
> These are bindings for at91-usart IP in spi spi mode. There is no support for

s/spi spi/SPI/

> internal chip select. Only kind of chip selects available are gpio chip

GPIO

> selects.
>
> Signed-off-by: Radu Pirea <radu.pirea@microchip.com>
> ---
> .../bindings/spi/microchip,at91-usart-spi.txt | 28 +++++++++++++++++++
> 1 file changed, 28 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/spi/microchip,at91-usart-spi.txt
>
> diff --git a/Documentation/devicetree/bindings/spi/microchip,at91-usart-spi.txt b/Documentation/devicetree/bindings/spi/microchip,at91-usart-spi.txt
> new file mode 100644
> index 000000000000..b68a3bec4121
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/spi/microchip,at91-usart-spi.txt

So now we have 2 copies of the same thing that varies by 2 properties?
Please make this one doc.

> @@ -0,0 +1,28 @@
> +* Universal Synchronous Asynchronous Receiver/Transmitter (USART) in SPI mode
> +
> +Required properties:
> +- #size-cells : Must be <0>
> +- #address-cells : Must be <1>
> +- compatible: Should be "atmel,at91rm9200-usart" or "atmel,at91sam9260-usart"
> +- reg: Should contain registers location and length
> +- interrupts: Should contain interrupt
> +- clocks: phandles to input clocks.
> +- clock-names: tuple listing input clock names.
> + Required elements: "usart"
> +- cs-gpios: chipselects (internal cs not supported)
> +- at91,usart-mode: AT91_USART_MODE_SPI (found in dt-bindings/mfd/at91-usart.h)

at91 is not a vendor.


> +
> +Example:
> + #include <dt-bindings/mfd/at91-usart.h>
> +
> + spi0: spi@f001c000 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + compatible = "atmel,at91rm9200-usart", "atmel,at91sam9260-usart";
> + at91,usart-mode = <AT91_USART_MODE_SPI>;
> + reg = <0xf001c000 0x100>;
> + interrupts = <12 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&usart0_clk>;
> + clock-names = "usart";
> + cs-gpios = <&pioB 3 0>;
> + };
> --
> 2.17.0
>

\
 
 \ /
  Last update: 2018-05-18 23:41    [W:0.297 / U:1.232 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site