lkml.org 
[lkml]   [2018]   [May]   [18]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH] arm64: dts: stingray: use NUM_SATA to configure number of sata ports
Date
Move remaining sata configuration to stingray-sata.dtsi and enable
ports based on NUM_SATA defined.
Now, all that needs to be done is define NUM_SATA per board.

Signed-off-by: Scott Branden <scott.branden@broadcom.com>
---
.../boot/dts/broadcom/stingray/bcm958742-base.dtsi | 64 --------------------
.../boot/dts/broadcom/stingray/bcm958742k.dts | 2 +
.../boot/dts/broadcom/stingray/bcm958742t.dts | 2 +
.../boot/dts/broadcom/stingray/stingray-sata.dtsi | 68 ++++++++++++++++++++++
4 files changed, 72 insertions(+), 64 deletions(-)

diff --git a/arch/arm64/boot/dts/broadcom/stingray/bcm958742-base.dtsi b/arch/arm64/boot/dts/broadcom/stingray/bcm958742-base.dtsi
index 8862ec9..cacc25e 100644
--- a/arch/arm64/boot/dts/broadcom/stingray/bcm958742-base.dtsi
+++ b/arch/arm64/boot/dts/broadcom/stingray/bcm958742-base.dtsi
@@ -72,70 +72,6 @@
<0x00000008 0x80000000 0x1 0x80000000>; /* 6G @ 34G */
};

-&sata0 {
- status = "okay";
-};
-
-&sata_phy0{
- status = "okay";
-};
-
-&sata1 {
- status = "okay";
-};
-
-&sata_phy1{
- status = "okay";
-};
-
-&sata2 {
- status = "okay";
-};
-
-&sata_phy2{
- status = "okay";
-};
-
-&sata3 {
- status = "okay";
-};
-
-&sata_phy3{
- status = "okay";
-};
-
-&sata4 {
- status = "okay";
-};
-
-&sata_phy4{
- status = "okay";
-};
-
-&sata5 {
- status = "okay";
-};
-
-&sata_phy5{
- status = "okay";
-};
-
-&sata6 {
- status = "okay";
-};
-
-&sata_phy6{
- status = "okay";
-};
-
-&sata7 {
- status = "okay";
-};
-
-&sata_phy7{
- status = "okay";
-};
-
&mdio_mux_iproc {
mdio@10 {
gphy0: eth-phy@10 {
diff --git a/arch/arm64/boot/dts/broadcom/stingray/bcm958742k.dts b/arch/arm64/boot/dts/broadcom/stingray/bcm958742k.dts
index 77efa28..a515346 100644
--- a/arch/arm64/boot/dts/broadcom/stingray/bcm958742k.dts
+++ b/arch/arm64/boot/dts/broadcom/stingray/bcm958742k.dts
@@ -32,6 +32,8 @@

/dts-v1/;

+#define NUM_SATA 8
+
#include "bcm958742-base.dtsi"

/ {
diff --git a/arch/arm64/boot/dts/broadcom/stingray/bcm958742t.dts b/arch/arm64/boot/dts/broadcom/stingray/bcm958742t.dts
index 5084b03..6a4d19e 100644
--- a/arch/arm64/boot/dts/broadcom/stingray/bcm958742t.dts
+++ b/arch/arm64/boot/dts/broadcom/stingray/bcm958742t.dts
@@ -32,6 +32,8 @@

/dts-v1/;

+#define NUM_SATA 8
+
#include "bcm958742-base.dtsi"

/ {
diff --git a/arch/arm64/boot/dts/broadcom/stingray/stingray-sata.dtsi b/arch/arm64/boot/dts/broadcom/stingray/stingray-sata.dtsi
index 8c68e0c..7f6d176 100644
--- a/arch/arm64/boot/dts/broadcom/stingray/stingray-sata.dtsi
+++ b/arch/arm64/boot/dts/broadcom/stingray/stingray-sata.dtsi
@@ -43,7 +43,11 @@
interrupts = <GIC_SPI 321 IRQ_TYPE_LEVEL_HIGH>;
#address-cells = <1>;
#size-cells = <0>;
+#if (NUM_SATA > 0)
+ status = "okay";
+#else
status = "disabled";
+#endif

sata0_port0: sata-port@0 {
reg = <0>;
@@ -58,7 +62,11 @@
reg-names = "phy";
#address-cells = <1>;
#size-cells = <0>;
+#if (NUM_SATA > 0)
+ status = "okay";
+#else
status = "disabled";
+#endif

sata0_phy0: sata-phy@0 {
reg = <0>;
@@ -73,7 +81,11 @@
interrupts = <GIC_SPI 323 IRQ_TYPE_LEVEL_HIGH>;
#address-cells = <1>;
#size-cells = <0>;
+#if (NUM_SATA > 1)
+ status = "okay";
+#else
status = "disabled";
+#endif

sata1_port0: sata-port@0 {
reg = <0>;
@@ -88,7 +100,11 @@
reg-names = "phy";
#address-cells = <1>;
#size-cells = <0>;
+#if (NUM_SATA > 1)
+ status = "okay";
+#else
status = "disabled";
+#endif

sata1_phy0: sata-phy@0 {
reg = <0>;
@@ -103,7 +119,11 @@
interrupts = <GIC_SPI 325 IRQ_TYPE_LEVEL_HIGH>;
#address-cells = <1>;
#size-cells = <0>;
+#if (NUM_SATA > 2)
+ status = "okay";
+#else
status = "disabled";
+#endif

sata2_port0: sata-port@0 {
reg = <0>;
@@ -118,7 +138,11 @@
reg-names = "phy";
#address-cells = <1>;
#size-cells = <0>;
+#if (NUM_SATA > 2)
+ status = "okay";
+#else
status = "disabled";
+#endif

sata2_phy0: sata-phy@0 {
reg = <0>;
@@ -133,7 +157,11 @@
interrupts = <GIC_SPI 327 IRQ_TYPE_LEVEL_HIGH>;
#address-cells = <1>;
#size-cells = <0>;
+#if (NUM_SATA > 3)
+ status = "okay";
+#else
status = "disabled";
+#endif

sata3_port0: sata-port@0 {
reg = <0>;
@@ -148,7 +176,11 @@
reg-names = "phy";
#address-cells = <1>;
#size-cells = <0>;
+#if (NUM_SATA > 3)
+ status = "okay";
+#else
status = "disabled";
+#endif

sata3_phy0: sata-phy@0 {
reg = <0>;
@@ -163,7 +195,11 @@
interrupts = <GIC_SPI 329 IRQ_TYPE_LEVEL_HIGH>;
#address-cells = <1>;
#size-cells = <0>;
+#if (NUM_SATA > 4)
+ status = "okay";
+#else
status = "disabled";
+#endif

sata4_port0: sata-port@0 {
reg = <0>;
@@ -178,7 +214,11 @@
reg-names = "phy";
#address-cells = <1>;
#size-cells = <0>;
+#if (NUM_SATA > 4)
+ status = "okay";
+#else
status = "disabled";
+#endif

sata4_phy0: sata-phy@0 {
reg = <0>;
@@ -193,7 +233,11 @@
interrupts = <GIC_SPI 331 IRQ_TYPE_LEVEL_HIGH>;
#address-cells = <1>;
#size-cells = <0>;
+#if (NUM_SATA > 5)
+ status = "okay";
+#else
status = "disabled";
+#endif

sata5_port0: sata-port@0 {
reg = <0>;
@@ -208,7 +252,11 @@
reg-names = "phy";
#address-cells = <1>;
#size-cells = <0>;
+#if (NUM_SATA > 5)
+ status = "okay";
+#else
status = "disabled";
+#endif

sata5_phy0: sata-phy@0 {
reg = <0>;
@@ -223,7 +271,11 @@
interrupts = <GIC_SPI 333 IRQ_TYPE_LEVEL_HIGH>;
#address-cells = <1>;
#size-cells = <0>;
+#if (NUM_SATA > 6)
+ status = "okay";
+#else
status = "disabled";
+#endif

sata6_port0: sata-port@0 {
reg = <0>;
@@ -238,7 +290,11 @@
reg-names = "phy";
#address-cells = <1>;
#size-cells = <0>;
+#if (NUM_SATA > 6)
+ status = "okay";
+#else
status = "disabled";
+#endif

sata6_phy0: sata-phy@0 {
reg = <0>;
@@ -253,7 +309,11 @@
interrupts = <GIC_SPI 335 IRQ_TYPE_LEVEL_HIGH>;
#address-cells = <1>;
#size-cells = <0>;
+#if (NUM_SATA > 7)
+ status = "okay";
+#else
status = "disabled";
+#endif

sata7_port0: sata-port@0 {
reg = <0>;
@@ -268,11 +328,19 @@
reg-names = "phy";
#address-cells = <1>;
#size-cells = <0>;
+#if (NUM_SATA > 7)
+ status = "okay";
+#else
status = "disabled";
+#endif

sata7_phy0: sata-phy@0 {
reg = <0>;
#phy-cells = <0>;
};
};
+
+#if (NUM_SATA > 8)
+#error "NUM_SATA > 8"
+#endif
};
--
2.5.0
\
 
 \ /
  Last update: 2018-05-18 20:35    [W:0.108 / U:1.492 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site