lkml.org 
[lkml]   [2018]   [Apr]   [22]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH 8/9] mtd: nand: qcom: helper function for raw read
Hi Abhishek,

On Thu, 12 Apr 2018 12:36:42 +0530, Abhishek Sahu
<absahu@codeaurora.org> wrote:

> On 2018-04-10 15:14, Miquel Raynal wrote:
> > Hi Abhishek,
> > > On Wed, 4 Apr 2018 18:12:24 +0530, Abhishek Sahu
> > <absahu@codeaurora.org> wrote:
> > >> This patch does minor code reorganization for raw reads.
> >> Currently the raw read is required for complete page but for
> >> subsequent patches related with erased codeword bit flips
> >> detection, only few CW should be read. So, this patch adds
> >> helper function and introduces the read CW bitmask which
> >> specifies which CW reads are required in complete page.
> > > I am not sure this is the right approach for subpage reads. If the
> > controller supports it, you should just enable it in chip->options.
> >
> Thanks Miquel.
>
> It is internal to this file only. This patch makes one static helper
> function which provides the support to read subpages.

Drivers should expose raw helpers, why keeping this helper static then?

>
> >> >> Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
> >> ---
> >> drivers/mtd/nand/qcom_nandc.c | 186 >> +++++++++++++++++++++++++-----------------
> >> 1 file changed, 110 insertions(+), 76 deletions(-)
> >> >> diff --git a/drivers/mtd/nand/qcom_nandc.c >> b/drivers/mtd/nand/qcom_nandc.c
> >> index 40c790e..f5d1fa4 100644
> >> --- a/drivers/mtd/nand/qcom_nandc.c
> >> +++ b/drivers/mtd/nand/qcom_nandc.c
> >> @@ -1590,6 +1590,114 @@ static int check_flash_errors(struct >> qcom_nand_host *host, int cw_cnt)
> >> }
> >> >> /*
> >> + * Helper to perform the page raw read operation. The read_cw_mask >> will be
> >> + * used to specify the codewords for which the data should be read. >> The
> >> + * single page contains multiple CW. Sometime, only few CW data is >> required
> >> + * in complete page. Also, start address will be determined with
> >> + * this CW mask to skip unnecessary data copy from NAND flash device. >> Then,
> >> + * actual data copy from NAND controller to data buffer will be done >> only
> >> + * for the CWs which have the mask set.
> >> + */
> >> +static int
> >> +nandc_read_page_raw(struct mtd_info *mtd, struct nand_chip *chip,
> >> + u8 *data_buf, u8 *oob_buf,
> >> + int page, unsigned long read_cw_mask)
> >> +{
> >> + struct qcom_nand_host *host = to_qcom_nand_host(chip);
> >> + struct qcom_nand_controller *nandc = get_qcom_nand_controller(chip);
> >> + struct nand_ecc_ctrl *ecc = &chip->ecc;
> >> + int i, ret;
> >> + int read_loc, start_step, last_step;
> >> +
> >> + nand_read_page_op(chip, page, 0, NULL, 0);
> >> +
> >> + host->use_ecc = false;
> >> + start_step = ffs(read_cw_mask) - 1;
> >> + last_step = fls(read_cw_mask);
> >> +
> >> + clear_bam_transaction(nandc);
> >> + set_address(host, host->cw_size * start_step, page);
> >> + update_rw_regs(host, last_step - start_step, true);
> >> + config_nand_page_read(nandc);
> >> +
> >> + for (i = start_step; i < last_step; i++) {
> >> + int data_size1, data_size2, oob_size1, oob_size2;
> >> + int reg_off = FLASH_BUF_ACC;
> >> +
> >> + data_size1 = mtd->writesize - host->cw_size * (ecc->steps - 1);
> >> + oob_size1 = host->bbm_size;
> >> +
> >> + if (i == (ecc->steps - 1)) {
> >> + data_size2 = ecc->size - data_size1 -
> >> + ((ecc->steps - 1) << 2);
> >> + oob_size2 = (ecc->steps << 2) + host->ecc_bytes_hw +
> >> + host->spare_bytes;
> >> + } else {
> >> + data_size2 = host->cw_data - data_size1;
> >> + oob_size2 = host->ecc_bytes_hw + host->spare_bytes;
> >> + }
> >> +
> >> + /*
> >> + * Don't perform actual data copy from NAND controller to data
> >> + * buffer through DMA for this codeword
> >> + */
> >> + if (!(read_cw_mask & BIT(i))) {
> >> + if (nandc->props->is_bam)
> >> + nandc_set_read_loc(nandc, 0, 0, 0, 1);
> >> +
> >> + config_nand_cw_read(nandc, false);
> >> +
> >> + data_buf += data_size1 + data_size2;
> >> + oob_buf += oob_size1 + oob_size2;
> >> +
> >> + continue;
> >> + }
> >> +
> >> + if (nandc->props->is_bam) {
> >> + read_loc = 0;
> >> + nandc_set_read_loc(nandc, 0, read_loc, data_size1, 0);
> >> + read_loc += data_size1;
> >> +
> >> + nandc_set_read_loc(nandc, 1, read_loc, oob_size1, 0);
> >> + read_loc += oob_size1;
> >> +
> >> + nandc_set_read_loc(nandc, 2, read_loc, data_size2, 0);
> >> + read_loc += data_size2;
> >> +
> >> + nandc_set_read_loc(nandc, 3, read_loc, oob_size2, 1);
> >> + }
> >> +
> >> + config_nand_cw_read(nandc, false);
> >> +
> >> + read_data_dma(nandc, reg_off, data_buf, data_size1, 0);
> >> + reg_off += data_size1;
> >> + data_buf += data_size1;
> >> +
> >> + read_data_dma(nandc, reg_off, oob_buf, oob_size1, 0);
> >> + reg_off += oob_size1;
> >> + oob_buf += oob_size1;
> >> +
> >> + read_data_dma(nandc, reg_off, data_buf, data_size2, 0);
> >> + reg_off += data_size2;
> >> + data_buf += data_size2;
> >> +
> >> + read_data_dma(nandc, reg_off, oob_buf, oob_size2, 0);
> >> + oob_buf += oob_size2;
> >> + }
> >> +
> >> + ret = submit_descs(nandc);
> >> + if (ret)
> >> + dev_err(nandc->dev, "failure to read raw page\n");
> >> +
> >> + free_descs(nandc);
> >> +
> >> + if (!ret)
> >> + ret = check_flash_errors(host, last_step - start_step);
> >> +
> >> + return 0;
> >> +}
> >> +
> >> +/*
> >> * reads back status registers set by the controller to notify page >> read
> >> * errors. this is equivalent to what 'ecc->correct()' would do.
> >> */
> >> @@ -1839,82 +1947,8 @@ static int qcom_nandc_read_page_raw(struct >> mtd_info *mtd,
> >> struct nand_chip *chip, uint8_t *buf,
> >> int oob_required, int page)
> >> {
> >> - struct qcom_nand_host *host = to_qcom_nand_host(chip);
> >> - struct qcom_nand_controller *nandc = get_qcom_nand_controller(chip);
> >> - u8 *data_buf, *oob_buf;
> >> - struct nand_ecc_ctrl *ecc = &chip->ecc;
> >> - int i, ret;
> >> - int read_loc;
> >> -
> >> - nand_read_page_op(chip, page, 0, NULL, 0);
> >> - data_buf = buf;
> >> - oob_buf = chip->oob_poi;
> >> -
> >> - host->use_ecc = false;
> >> -
> >> - clear_bam_transaction(nandc);
> >> - update_rw_regs(host, ecc->steps, true);
> >> - config_nand_page_read(nandc);
> >> -
> >> - for (i = 0; i < ecc->steps; i++) {
> >> - int data_size1, data_size2, oob_size1, oob_size2;
> >> - int reg_off = FLASH_BUF_ACC;
> >> -
> >> - data_size1 = mtd->writesize - host->cw_size * (ecc->steps - 1);
> >> - oob_size1 = host->bbm_size;
> >> -
> >> - if (i == (ecc->steps - 1)) {
> >> - data_size2 = ecc->size - data_size1 -
> >> - ((ecc->steps - 1) << 2);
> >> - oob_size2 = (ecc->steps << 2) + host->ecc_bytes_hw +
> >> - host->spare_bytes;
> >> - } else {
> >> - data_size2 = host->cw_data - data_size1;
> >> - oob_size2 = host->ecc_bytes_hw + host->spare_bytes;
> >> - }
> >> -
> >> - if (nandc->props->is_bam) {
> >> - read_loc = 0;
> >> - nandc_set_read_loc(nandc, 0, read_loc, data_size1, 0);
> >> - read_loc += data_size1;
> >> -
> >> - nandc_set_read_loc(nandc, 1, read_loc, oob_size1, 0);
> >> - read_loc += oob_size1;
> >> -
> >> - nandc_set_read_loc(nandc, 2, read_loc, data_size2, 0);
> >> - read_loc += data_size2;
> >> -
> >> - nandc_set_read_loc(nandc, 3, read_loc, oob_size2, 1);
> >> - }
> >> -
> >> - config_nand_cw_read(nandc, false);
> >> -
> >> - read_data_dma(nandc, reg_off, data_buf, data_size1, 0);
> >> - reg_off += data_size1;
> >> - data_buf += data_size1;
> >> -
> >> - read_data_dma(nandc, reg_off, oob_buf, oob_size1, 0);
> >> - reg_off += oob_size1;
> >> - oob_buf += oob_size1;
> >> -
> >> - read_data_dma(nandc, reg_off, data_buf, data_size2, 0);
> >> - reg_off += data_size2;
> >> - data_buf += data_size2;
> >> -
> >> - read_data_dma(nandc, reg_off, oob_buf, oob_size2, 0);
> >> - oob_buf += oob_size2;
> >> - }
> >> -
> >> - ret = submit_descs(nandc);
> >> - if (ret)
> >> - dev_err(nandc->dev, "failure to read raw page\n");
> >> -
> >> - free_descs(nandc);
> >> -
> >> - if (!ret)
> >> - ret = check_flash_errors(host, ecc->steps);
> >> -
> >> - return 0;
> >> + return nandc_read_page_raw(mtd, chip, buf, chip->oob_poi, page,
> >> + BIT(chip->ecc.steps) - 1);
> > > I don't understand this. chip->ecc.steps is constant, right? So you
> > always ask for the same subpage?
>
> We need to do raw read for subpages in which we got uncorrectable
> error in next patch for erased page bitflip detection. This patch does
> reorganization of raw read and moves common code in helper function
> nandc_read_page_raw.
>
> For nomral raw read, all the subpages will be read so
> BIT(chip->ecc.steps) - 1 is used for qcom_nandc_read_page_raw.
>
> While for erased page raw read, only those sub pages will be
> read for which the controller gives the uncorrectable error.

Still not okay: the driver should expose a way to do raw reads no
matter the length and the start and you should use that in a generic
way.

>
> Thanks,
> Abhishek
>
> > >> }
> >> >> /* implements ecc->read_oob() */



--
Miquel Raynal, Bootlin (formerly Free Electrons)
Embedded Linux and Kernel engineering
https://bootlin.com

\
 
 \ /
  Last update: 2018-04-22 18:20    [W:0.176 / U:1.820 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site