lkml.org 
[lkml]   [2018]   [Mar]   [27]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH] Input: ALPS - add support for 73 03 28 devices (Thinkpad L570)
From
Date
Hi,

oh ok, understood. Thanks for this hint.

So maybe there is something wrong with the alps_update_dual_info_ss4_v2
function or the reporting of the hardware.

alps_update_dual_info_ss4_v2 detects the ThinkPad L570 as ss4plus device
but not as dualpoint device. This means that the ALPS_DUALPOINT and the
ALPS_DUALPOINT_WITH_PRESSURE flag will not be set which results in a non
function trackstick and hardware mouse buttons. Each time I touch the
trackstick I get the message: "alps: Rejected trackstick packet from non
DualPoint device".

The value of otp[0][0] inside alps_update_dual_info_ss4_v2 is 0xCE. Are
there any ideas why it is not detected as dualpoint device?

Thank you & best regards,

Dennis

On 23.03.2018 15:33, Pali Rohár wrote:
> On Friday 23 March 2018 15:23:55 Dennis Wassenberg wrote:
>> The Lenovo Thinkpad L570 uses V8 protocol.
>> Add 0x73 0x03 0x28 devices to use V8 protovol which makes
>> trackstick and mouse buttons work with Lenovo Thinkpad L570.
>>
>> Signed-off-by: Dennis Wassenberg <dennis.wassenberg@secunet.com>
>> ---
>> drivers/input/mouse/alps.c | 2 ++
>> 1 file changed, 2 insertions(+)
>>
>> diff --git a/drivers/input/mouse/alps.c b/drivers/input/mouse/alps.c
>> index dbe57da..5523d4e 100644
>> --- a/drivers/input/mouse/alps.c
>> +++ b/drivers/input/mouse/alps.c
>> @@ -136,6 +136,8 @@
>> { { 0x73, 0x02, 0x0a }, { ALPS_PROTO_V2, 0xf8, 0xf8, 0 } },
>> { { 0x73, 0x02, 0x14 }, { ALPS_PROTO_V2, 0xf8, 0xf8, ALPS_FW_BK_2 } }, /* Ahtec Laptop */
>> { { 0x73, 0x02, 0x50 }, { ALPS_PROTO_V2, 0xcf, 0xcf, ALPS_FOUR_BUTTONS } }, /* Dell Vostro 1400 */
>> + { { 0x73, 0x03, 0x28 }, { ALPS_PROTO_V8, 0x18, 0x18,
>> + ALPS_DUALPOINT | ALPS_DUALPOINT_WITH_PRESSURE | ALPS_BUTTONPAD } }, /* Lenovo L570 */
>> };
>>
>> static const struct alps_protocol_info alps_v3_protocol_data = {
>
> Hi! alps_model_data table is used for fixed identification of v1 and v2
> protocols. Why you need to add there v8 protocol which autodetection is
> already done in alps_identify() function? There is already code:
>
> } else if (e7[0] == 0x73 && e7[1] == 0x03 &&
> (e7[2] == 0x14 || e7[2] == 0x28)) {
> protocol = &alps_v8_protocol_data;
>
> Which matches above your E7 detection 0x73, 0x03, 0x28.
>
> Also you patch matches basically all v8 device and therefore has
> potential to break proper v8 autodetection for other v8 devices...
>

\
 
 \ /
  Last update: 2018-03-27 16:01    [W:0.087 / U:1.484 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site