lkml.org 
[lkml]   [2018]   [Mar]   [23]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Subject[PATCH v4 0/8] ARM: davinci: complete the conversion to using the reset framework
Date
From: Bartosz Golaszewski <bgolaszewski@baylibre.com>

This series converts the only user of the handcoded, mach-specific reset
routines in the davinci platform to using the reset framework.

Patch 1 modifies the way lookup entries are registered with the reset
framework.

Patches 2-4 add necessary lookups/DT-properties.

Patches 5-7 convert the davinci-rproc driver to the reset framework.

Patch 8 removes now dead code.

Philipp: it turned out that it's indeed better to use the reset
controller's device name for the entry lookup.

Tested both in DT and legacy modes by booting the examples from
ti-ipc-rtos recipe in meta-ti.

This series applies on top of David Lechner's common-clk-v9 branch[1]
with Philipp Zabel's reset/next branch[2] pulled in.

It can be found in my github tree as well[3].

[1] git://github.com/dlech/ev3dev-kernel.git common-clk-v9
[2] git://git.pengutronix.de/git/pza/linux reset/next
[3] git@github.com:brgl/linux.git topic/davinci-reset

v1 -> v2:
- fixed the device tree patches the descriptions of which were mixed up
- return -EPROBE_DEFER from davinci-rproc's probe() if we can't get the
reset provider, since it's possible that the lookup table was not yet
registered
- made the local variable naming consistent in the davinci-rproc driver
- fixed a typo in PATCH 5/8

v2 -> v3:
- modify PATCH 1/8: drop the provider argument from the function adding
lookup entries and instead pass the provider name to the RESET_LOOKUP
macro, return -EPROBE_DEFER if we locate a correct lookup entry but
cannot get the corresponding reset controller
- modify the reset lookup entry in psc-da850
- don't manually return -EPROBE_DEFER from davinci-rproc, instead don't
emit an error message if devm_reset_control_get_exclusive() returns
this error code

v3 -> v4:
- make index the second parameter in RESET_LOOKUP() (right after the
provider name)

Bartosz Golaszewski (8):
reset: modify the way reset lookup works for board files
ARM: davinci: dts: make psc0 a reset provider
ARM: davinci: dts: add a reset control to the dsp node
clk: davinci: add a reset lookup table for psc0
remoteproc: da8xx: add the missing retval check for clk_enable()
remoteproc: da8xx: prepare and unprepare the clock where needed
remoteproc: da8xx: use the reset framework
clk: davinci: kill davinci_clk_reset_assert/deassert()

arch/arm/boot/dts/da850.dtsi | 2 ++
arch/arm/mach-davinci/include/mach/clock.h | 21 ---------------
drivers/clk/davinci/psc-da850.c | 7 +++++
drivers/clk/davinci/psc.c | 19 +-------------
drivers/remoteproc/da8xx_remoteproc.c | 42 +++++++++++++++++++++++++-----
drivers/reset/core.c | 38 ++++++++++++++++++++++-----
include/linux/reset-controller.h | 14 +++++-----
7 files changed, 84 insertions(+), 59 deletions(-)
delete mode 100644 arch/arm/mach-davinci/include/mach/clock.h

--
2.16.1

\
 
 \ /
  Last update: 2018-03-23 14:05    [W:0.142 / U:0.200 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site