lkml.org 
[lkml]   [2018]   [Mar]   [23]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v3 1/6] phy: qcom-qmp: Enable pipe_clk before checking USB3 PHY_STATUS
Date
QMP PHY for USB mode requires pipe_clk for calibration and PLL lock
to take place. This clock is output from PHY to GCC clock_ctl and then
fed back to QMP PHY and is available from PHY only after PHY is reset
and initialized, hence it can't be enabled too early in initialization
sequence.

Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
---
drivers/phy/qualcomm/phy-qcom-qmp.c | 33 ++++++++++++++++++++++++++++++++-
1 file changed, 32 insertions(+), 1 deletion(-)

diff --git a/drivers/phy/qualcomm/phy-qcom-qmp.c b/drivers/phy/qualcomm/phy-qcom-qmp.c
index 6470c5d..5d8df6a 100644
--- a/drivers/phy/qualcomm/phy-qcom-qmp.c
+++ b/drivers/phy/qualcomm/phy-qcom-qmp.c
@@ -1008,6 +1008,19 @@ static int qcom_qmp_phy_init(struct phy *phy)
status = pcs + cfg->regs[QPHY_PCS_READY_STATUS];
mask = cfg->mask_pcs_ready;

+ /*
+ * USB3 PHY requires pipe_clk for PLL lock and calibration.
+ * Enable it from here for USB. For UFS/PCIE, it gets enabled
+ * from poweron.
+ */
+ if (cfg->type == PHY_TYPE_USB3) {
+ ret = clk_prepare_enable(qphy->pipe_clk);
+ if (ret) {
+ dev_err(qmp->dev, "pipe_clk enable err=%d\n", ret);
+ goto err_clk_enable;
+ }
+ }
+
ret = readl_poll_timeout(status, val, !(val & mask), 1,
PHY_INIT_COMPLETE_TIMEOUT);
if (ret) {
@@ -1019,6 +1032,9 @@ static int qcom_qmp_phy_init(struct phy *phy)
return ret;

err_pcs_ready:
+ if (cfg->type == PHY_TYPE_USB3)
+ clk_disable_unprepare(qphy->pipe_clk);
+err_clk_enable:
if (cfg->has_lane_rst)
reset_control_assert(qphy->lane_rst);
err_lane_rst:
@@ -1288,10 +1304,19 @@ static int phy_pipe_clk_register(struct qcom_qmp *qmp, struct device_node *np)
.owner = THIS_MODULE,
};

+/* USB PHY doesn't require power_on op */
+static const struct phy_ops qcom_qmp_usb_phy_gen_ops = {
+ .init = qcom_qmp_phy_init,
+ .exit = qcom_qmp_phy_exit,
+ .set_mode = qcom_qmp_phy_set_mode,
+ .owner = THIS_MODULE,
+};
+
static
int qcom_qmp_phy_create(struct device *dev, struct device_node *np, int id)
{
struct qcom_qmp *qmp = dev_get_drvdata(dev);
+ const struct phy_ops *ops;
struct phy *generic_phy;
struct qmp_phy *qphy;
char prop_name[MAX_PROP_NAME];
@@ -1354,7 +1379,13 @@ int qcom_qmp_phy_create(struct device *dev, struct device_node *np, int id)
}
}

- generic_phy = devm_phy_create(dev, np, &qcom_qmp_phy_gen_ops);
+ /* USB PHY doesn't use power_on op */
+ if (qmp->cfg->type == PHY_TYPE_USB3)
+ ops = &qcom_qmp_usb_phy_gen_ops;
+ else
+ ops = &qcom_qmp_phy_gen_ops;
+
+ generic_phy = devm_phy_create(dev, np, ops);
if (IS_ERR(generic_phy)) {
ret = PTR_ERR(generic_phy);
dev_err(dev, "failed to create qphy %d\n", ret);
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
\
 
 \ /
  Last update: 2018-03-23 07:14    [W:0.201 / U:2.224 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site