lkml.org 
[lkml]   [2018]   [Feb]   [12]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH 10/21] regulator: lp8788-ldo: Pass descriptor instead of GPIO number
On Mon, 12 Feb 2018, Linus Walleij wrote:

> Instead of passing a global GPIO number, pass a descriptor looked
> up with the standard devm_gpiod_get_index_optional() call.
>
> This driver has supported passing a LDO enable GPIO for years,
> yet this facility has never been put to use in the upstream kernel.
> If someone desires to put in place GPIO control for the LDOs,
> this can be done by adding a GPIO descriptor table in the MFD
> nexus in drivers/mfd/lp8788.c for the LDO device when spawning the
> MFD children, or using a board file.
>
> Cc: Milo Kim <milo.kim@ti.com>
> Cc: Lee Jones <lee.jones@linaro.org>
> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
> ---
> Lee: would be nice if you could ACK this smallish patch to
> the MFD header.

Fine, but any sign of a conflict and I'll need a PR.

Acked-by: Lee Jones <lee.jones@linaro.org>

> ---
> drivers/regulator/lp8788-ldo.c | 32 ++++++++++++++++----------------
> include/linux/mfd/lp8788.h | 16 ----------------
> 2 files changed, 16 insertions(+), 32 deletions(-)
>
> diff --git a/drivers/regulator/lp8788-ldo.c b/drivers/regulator/lp8788-ldo.c
> index cbfd35873575..f2347474a106 100644
> --- a/drivers/regulator/lp8788-ldo.c
> +++ b/drivers/regulator/lp8788-ldo.c
> @@ -16,7 +16,7 @@
> #include <linux/err.h>
> #include <linux/platform_device.h>
> #include <linux/regulator/driver.h>
> -#include <linux/gpio.h>
> +#include <linux/gpio/consumer.h>
> #include <linux/mfd/lp8788.h>
>
> /* register address */
> @@ -85,8 +85,6 @@
> #define LP8788_STARTUP_TIME_S 3
>
> #define ENABLE_TIME_USEC 32
> -#define ENABLE GPIOF_OUT_INIT_HIGH
> -#define DISABLE GPIOF_OUT_INIT_LOW
>
> enum lp8788_ldo_id {
> DLDO1,
> @@ -117,7 +115,7 @@ struct lp8788_ldo {
> struct lp8788 *lp;
> struct regulator_desc *desc;
> struct regulator_dev *regulator;
> - struct lp8788_ldo_enable_pin *en_pin;
> + struct gpio_desc *ena_gpiod;
> };
>
> /* DLDO 1, 2, 3, 9 voltage table */
> @@ -469,7 +467,6 @@ static int lp8788_config_ldo_enable_mode(struct platform_device *pdev,
> enum lp8788_ldo_id id)
> {
> struct lp8788 *lp = ldo->lp;
> - struct lp8788_platform_data *pdata = lp->pdata;
> enum lp8788_ext_ldo_en_id enable_id;
> u8 en_mask[] = {
> [EN_ALDO1] = LP8788_EN_SEL_ALDO1_M,
> @@ -504,11 +501,18 @@ static int lp8788_config_ldo_enable_mode(struct platform_device *pdev,
> return 0;
> }
>
> - /* if no platform data for ldo pin, then set default enable mode */
> - if (!pdata || !pdata->ldo_pin || !pdata->ldo_pin[enable_id])
> + /* FIXME: check default mode for GPIO here: high or low? */
> + ldo->ena_gpiod = devm_gpiod_get_index_optional(&pdev->dev,
> + "enable",
> + enable_id,
> + GPIOD_OUT_HIGH);
> + if (IS_ERR(ldo->ena_gpiod))
> + return PTR_ERR(ldo->ena_gpiod);
> +
> + /* if no GPIO for ldo pin, then set default enable mode */
> + if (!ldo->ena_gpiod)
> goto set_default_ldo_enable_mode;
>
> - ldo->en_pin = pdata->ldo_pin[enable_id];
> return 0;
>
> set_default_ldo_enable_mode:
> @@ -533,10 +537,8 @@ static int lp8788_dldo_probe(struct platform_device *pdev)
> if (ret)
> return ret;
>
> - if (ldo->en_pin) {
> - cfg.ena_gpio = ldo->en_pin->gpio;
> - cfg.ena_gpio_flags = ldo->en_pin->init_state;
> - }
> + if (ldo->ena_gpiod)
> + cfg.ena_gpiod = ldo->ena_gpiod;
>
> cfg.dev = pdev->dev.parent;
> cfg.init_data = lp->pdata ? lp->pdata->dldo_data[id] : NULL;
> @@ -582,10 +584,8 @@ static int lp8788_aldo_probe(struct platform_device *pdev)
> if (ret)
> return ret;
>
> - if (ldo->en_pin) {
> - cfg.ena_gpio = ldo->en_pin->gpio;
> - cfg.ena_gpio_flags = ldo->en_pin->init_state;
> - }
> + if (ldo->ena_gpiod)
> + cfg.ena_gpiod = ldo->ena_gpiod;
>
> cfg.dev = pdev->dev.parent;
> cfg.init_data = lp->pdata ? lp->pdata->aldo_data[id] : NULL;
> diff --git a/include/linux/mfd/lp8788.h b/include/linux/mfd/lp8788.h
> index 786bf6679a28..2010e0de3e34 100644
> --- a/include/linux/mfd/lp8788.h
> +++ b/include/linux/mfd/lp8788.h
> @@ -181,20 +181,6 @@ struct lp8788_buck2_dvs {
> enum lp8788_dvs_sel vsel;
> };
>
> -/*
> - * struct lp8788_ldo_enable_pin
> - *
> - * Basically, all LDOs are enabled through the I2C commands.
> - * But ALDO 1 ~ 5, 7, DLDO 7, 9, 11 can be enabled by external gpio pins.
> - *
> - * @gpio : gpio number which is used for enabling ldos
> - * @init_state : initial gpio state (ex. GPIOF_OUT_INIT_LOW)
> - */
> -struct lp8788_ldo_enable_pin {
> - int gpio;
> - int init_state;
> -};
> -
> /*
> * struct lp8788_chg_param
> * @addr : charging control register address (range : 0x11 ~ 0x1C)
> @@ -288,7 +274,6 @@ struct lp8788_vib_platform_data {
> * @aldo_data : regulator initial data for analog ldo
> * @buck1_dvs : gpio configurations for buck1 dvs
> * @buck2_dvs : gpio configurations for buck2 dvs
> - * @ldo_pin : gpio configurations for enabling LDOs
> * @chg_pdata : platform data for charger driver
> * @alarm_sel : rtc alarm selection (1 or 2)
> * @bl_pdata : configurable data for backlight driver
> @@ -306,7 +291,6 @@ struct lp8788_platform_data {
> struct regulator_init_data *aldo_data[LP8788_NUM_ALDOS];
> struct lp8788_buck1_dvs *buck1_dvs;
> struct lp8788_buck2_dvs *buck2_dvs;
> - struct lp8788_ldo_enable_pin *ldo_pin[EN_LDOS_MAX];
>
> /* charger */
> struct lp8788_charger_platform_data *chg_pdata;

--
Lee Jones
Linaro Services Technical Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog

\
 
 \ /
  Last update: 2018-02-12 16:01    [W:0.277 / U:0.736 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site