lkml.org 
[lkml]   [2018]   [Dec]   [7]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v6 2/5] phy: qcom-qmp: Utilize fully-specified DT registers
From
Date
Hi,

On 07/12/18 2:16 PM, Vivek Gautam wrote:
> On Fri, Dec 7, 2018 at 5:06 AM Evan Green <evgreen@chromium.org> wrote:
>>
>> Utilize the newly fixed up DT bindings to get the tx2 and rx2 register
>> regions for the second lane of dual-lane PHYs. Before this change,
>> the driver was simply using lane one's register region and adding
>> 0x400, which reached well beyond the DT-specified register
>> allocation. This would have been a crash were it not for the page size
>> on ARM64. Fix the driver not to rely on the magic of virtual memory by
>> using the newly specified DT register regions for tx2 and rx2.
>>
>> In order to support existing device trees, this change also contains a
>> fallback mode for when those new register regions don't exist, which
>> reverts to the original behavior of overreaching and prints a complaint.
>>
>> Signed-off-by: Evan Green <evgreen@chromium.org>
>> Reviewed-by: Douglas Anderson <dianders@chromium.org>
>> ---
>> As Doug mentioned, this should land before the dts patches land, otherwise
>> the old driver code will use the tx2 register region as pcs_misc.
>>
>> Changes in v6: None
>> Changes in v5: None
>> Changes in v4: None
>> Changes in v3: None
>> Changes in v2: None
>>
>> drivers/phy/qualcomm/phy-qcom-qmp.c | 51 +++++++++++++++++++++--------
>> 1 file changed, 38 insertions(+), 13 deletions(-)
>>
>> diff --git a/drivers/phy/qualcomm/phy-qcom-qmp.c b/drivers/phy/qualcomm/phy-qcom-qmp.c
>> index 514db7248a5d0..8204d55e2d650 100644
>> --- a/drivers/phy/qualcomm/phy-qcom-qmp.c
>> +++ b/drivers/phy/qualcomm/phy-qcom-qmp.c
>> @@ -72,6 +72,9 @@
>>
>> #define MAX_PROP_NAME 32
>>
>> +/* Define the assumed distance between lanes for underspecified device trees. */
>> +#define QMP_PHY_LEGACY_LANE_STRIDE 0x400
>> +
>> struct qmp_phy_init_tbl {
>> unsigned int offset;
>> unsigned int val;
>> @@ -733,9 +736,6 @@ struct qmp_phy_cfg {
>> bool has_phy_dp_com_ctrl;
>> /* true, if PHY has secondary tx/rx lanes to be configured */
>> bool is_dual_lane_phy;
>> - /* Register offset of secondary tx/rx lanes for USB DP combo PHY */
>> - unsigned int tx_b_lane_offset;
>> - unsigned int rx_b_lane_offset;
>>
>> /* true, if PCS block has no separate SW_RESET register */
>> bool no_pcs_sw_reset;
>> @@ -748,6 +748,8 @@ struct qmp_phy_cfg {
>> * @tx: iomapped memory space for lane's tx
>> * @rx: iomapped memory space for lane's rx
>> * @pcs: iomapped memory space for lane's pcs
>> + * @tx2: iomapped memory space for second lane's tx (in dual lane PHYs)
>> + * @rx2: iomapped memory space for second lane's rx (in dual lane PHYs)
>> * @pcs_misc: iomapped memory space for lane's pcs_misc
>> * @pipe_clk: pipe lock
>> * @index: lane index
>> @@ -759,6 +761,8 @@ struct qmp_phy {
>> void __iomem *tx;
>> void __iomem *rx;
>> void __iomem *pcs;
>> + void __iomem *tx2;
>> + void __iomem *rx2;
>> void __iomem *pcs_misc;
>> struct clk *pipe_clk;
>> unsigned int index;
>> @@ -975,8 +979,6 @@ static const struct qmp_phy_cfg qmp_v3_usb3phy_cfg = {
>>
>> .has_phy_dp_com_ctrl = true,
>> .is_dual_lane_phy = true,
>> - .tx_b_lane_offset = 0x400,
>> - .rx_b_lane_offset = 0x400,
>> };
>>
>> static const struct qmp_phy_cfg qmp_v3_usb3_uniphy_cfg = {
>> @@ -1031,9 +1033,6 @@ static const struct qmp_phy_cfg sdm845_ufsphy_cfg = {
>> .mask_pcs_ready = PCS_READY,
>>
>> .is_dual_lane_phy = true,
>> - .tx_b_lane_offset = 0x400,
>> - .rx_b_lane_offset = 0x400,
>> -
>> .no_pcs_sw_reset = true,
>> };
>>
>> @@ -1238,12 +1237,12 @@ static int qcom_qmp_phy_init(struct phy *phy)
>> qcom_qmp_phy_configure(tx, cfg->regs, cfg->tx_tbl, cfg->tx_tbl_num);
>> /* Configuration for other LANE for USB-DP combo PHY */
>> if (cfg->is_dual_lane_phy)
>> - qcom_qmp_phy_configure(tx + cfg->tx_b_lane_offset, cfg->regs,
>> + qcom_qmp_phy_configure(qphy->tx2, cfg->regs,
>> cfg->tx_tbl, cfg->tx_tbl_num);
>>
>> qcom_qmp_phy_configure(rx, cfg->regs, cfg->rx_tbl, cfg->rx_tbl_num);
>> if (cfg->is_dual_lane_phy)
>> - qcom_qmp_phy_configure(rx + cfg->rx_b_lane_offset, cfg->regs,
>> + qcom_qmp_phy_configure(qphy->rx2, cfg->regs,
>> cfg->rx_tbl, cfg->rx_tbl_num);
>>
>> qcom_qmp_phy_configure(pcs, cfg->regs, cfg->pcs_tbl, cfg->pcs_tbl_num);
>> @@ -1615,8 +1614,9 @@ int qcom_qmp_phy_create(struct device *dev, struct device_node *np, int id)
>>
>> /*
>> * Get memory resources for each phy lane:
>> - * Resources are indexed as: tx -> 0; rx -> 1; pcs -> 2; and
>> - * pcs_misc (optional) -> 3.
>> + * Resources are indexed as: tx -> 0; rx -> 1; pcs -> 2.
>> + * For dual lane PHYs: tx2 -> 3, rx2 -> 4, pcs_misc (optional) -> 5
>> + * For single lane PHYs: pcs_misc (optional) -> 3.
>> */
>> qphy->tx = of_iomap(np, 0);
>> if (!qphy->tx)
>> @@ -1630,7 +1630,32 @@ int qcom_qmp_phy_create(struct device *dev, struct device_node *np, int id)
>> if (!qphy->pcs)
>> return -ENOMEM;
>>
>> - qphy->pcs_misc = of_iomap(np, 3);
>> + /*
>> + * If this is a dual-lane PHY, then there should be registers for the
>> + * second lane. Some old device trees did not specify this, so fall
>> + * back to old legacy behavior of assuming they can be reached at an
>> + * offset from the first lane.
>> + */
>> + if (qmp->cfg->is_dual_lane_phy) {
>> + qphy->tx2 = of_iomap(np, 3);
>> + qphy->rx2 = of_iomap(np, 4);
>> + if (!qphy->tx2 || !qphy->rx2) {
>> + dev_warn(dev,
>> + "Underspecified device tree, falling back to legacy register regions\n");
>> +
>> + /* In the old version, pcs_misc is at index 3. */
>> + qphy->pcs_misc = qphy->tx2;
>> + qphy->tx2 = qphy->tx + QMP_PHY_LEGACY_LANE_STRIDE;
>> + qphy->rx2 = qphy->rx + QMP_PHY_LEGACY_LANE_STRIDE;
>> +
>> + } else {
>> + qphy->pcs_misc = of_iomap(np, 5);
>> + }
>> +
>> + } else {
>> + qphy->pcs_misc = of_iomap(np, 3);
>> + }
>> +
>> if (!qphy->pcs_misc)
>> dev_vdbg(dev, "PHY pcs_misc-reg not used\n");
>>
>> --
>> 2.18.1
>>
>
> Tested on db820c [1]. USB, PCIe come up.
> Tested-by: Vivek Gautam <vivek.gautam@codeaurora.org>
>
> [1] https://github.com/vivekgautam1/linux/tree/origin/v4.20-rc5/db820c

Thank you Vivek.
Evan, can you resend this series after rebasing to phy -next and also your
other series?

Thanks
Kishon

\
 
 \ /
  Last update: 2018-12-08 04:52    [W:0.086 / U:6.836 seconds]
©2003-2018 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site