lkml.org 
[lkml]   [2018]   [Dec]   [5]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v3 1/4] Bluetooth: hci_qca: use wait_until_sent() for power pulses
On Fri, Nov 30, 2018 at 08:32:44PM +0530, Balakrishna Godavarthi wrote:
> wcn3990 requires a power pulse to turn ON/OFF along with
> regulators. Sometimes we are observing the power pulses are sent
> out with some time delay, due to queuing these commands. This is
> causing synchronization issues with chip, which intern delay the
> chip setup or may end up with communication issues.
>
> Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
> ---
> v3:
> * no change.
> v2:
> * Updated function qca_send_power_pulse()
> * addressed reviewer comments.

Please make sure to include reviewers on CC when resending, and as
someone else already mentioned, be a bit more specific about what
changes you actually made in response to the review feedback you
received.

> v1:
> * initial patch
> ---
> drivers/bluetooth/hci_qca.c | 37 +++++++++++++------------------------
> 1 file changed, 13 insertions(+), 24 deletions(-)
>
> diff --git a/drivers/bluetooth/hci_qca.c b/drivers/bluetooth/hci_qca.c
> index f036c8f98ea3..f5dd323c1967 100644
> --- a/drivers/bluetooth/hci_qca.c
> +++ b/drivers/bluetooth/hci_qca.c
> @@ -1013,11 +1013,9 @@ static inline void host_set_baudrate(struct hci_uart *hu, unsigned int speed)
> hci_uart_set_baudrate(hu, speed);
> }
>
> -static int qca_send_power_pulse(struct hci_dev *hdev, u8 cmd)
> +static int qca_send_power_pulse(struct hci_uart *hu, u8 cmd)
> {
> - struct hci_uart *hu = hci_get_drvdata(hdev);
> - struct qca_data *qca = hu->priv;
> - struct sk_buff *skb;
> + int ret;
>
> /* These power pulses are single byte command which are sent
> * at required baudrate to wcn3990. On wcn3990, we have an external
> @@ -1029,19 +1027,16 @@ static int qca_send_power_pulse(struct hci_dev *hdev, u8 cmd)
> * save power. Disabling hardware flow control is mandatory while
> * sending power pulses to SoC.
> */
> - bt_dev_dbg(hdev, "sending power pulse %02x to SoC", cmd);
> -
> - skb = bt_skb_alloc(sizeof(cmd), GFP_KERNEL);
> - if (!skb)
> - return -ENOMEM;
> -
> + bt_dev_dbg(hu->hdev, "sending power pulse %02x to SoC", cmd);
> hci_uart_set_flow_control(hu, true);
> + ret = serdev_device_write(hu->serdev, &cmd, sizeof(cmd), 0);

You're still using 0 as a timeout here which is broken, as I already
told you.

From 4.21 this will result in an indefinite timeout, but currently
implies not to wait for a full write buffer to drain at all.

As I also mentioned, you need to to make sure to call
serdev_device_write_wakeup() in the write_wakup() path if you are going
to use serdev_device_write() at all.

Johan

\
 
 \ /
  Last update: 2018-12-05 07:25    [W:0.079 / U:2.252 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site