lkml.org 
[lkml]   [2018]   [Dec]   [3]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v3] USB: Don't enable LPM if it's already enabled
Date
USB Bluetooth controller QCA ROME (0cf3:e007) sometimes stops working
after S3:
[ 165.110742] Bluetooth: hci0: using NVM file: qca/nvm_usb_00000302.bin
[ 168.432065] Bluetooth: hci0: Failed to send body at 4 of 1953 (-110)

After some experiments, I found that disabling LPM can workaround the
issue.

On some platforms, the USB power is cut during S3, so the driver uses
reset-resume to resume the device. During port resume, LPM gets enabled
twice, by usb_reset_and_verify_device() and usb_port_resume().

So let's enable LPM for just once, as this solves the issue for the
device in question.

Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
---
v3:
- Consolidate udev->usb2_hw_lpm_capable and udev->usb2_hw_lpm_enabled
check to usb_set_usb2_hardware_lpm().
v2:
- Check udev->usb2_hw_lpm_enabled before calling usb_port_resume().

drivers/usb/core/driver.c | 4 +++-
drivers/usb/core/hub.c | 13 ++++---------
drivers/usb/core/message.c | 3 +--
3 files changed, 8 insertions(+), 12 deletions(-)

diff --git a/drivers/usb/core/driver.c b/drivers/usb/core/driver.c
index 53564386ed57..f277a8de7498 100644
--- a/drivers/usb/core/driver.c
+++ b/drivers/usb/core/driver.c
@@ -1901,7 +1901,9 @@ int usb_set_usb2_hardware_lpm(struct usb_device *udev, int enable)
struct usb_hcd *hcd = bus_to_hcd(udev->bus);
int ret = -EPERM;

- if (enable && !udev->usb2_hw_lpm_allowed)
+ if (!udev->usb2_hw_lpm_capable ||
+ (enable && !udev->usb2_hw_lpm_allowed) ||
+ (enable && udev->usb2_hw_lpm_enabled))
return 0;

if (hcd->driver->set_usb2_hw_lpm) {
diff --git a/drivers/usb/core/hub.c b/drivers/usb/core/hub.c
index e482e5f103d9..907793d38a82 100644
--- a/drivers/usb/core/hub.c
+++ b/drivers/usb/core/hub.c
@@ -3210,8 +3210,7 @@ int usb_port_suspend(struct usb_device *udev, pm_message_t msg)
}

/* disable USB2 hardware LPM */
- if (udev->usb2_hw_lpm_enabled == 1)
- usb_set_usb2_hardware_lpm(udev, 0);
+ usb_set_usb2_hardware_lpm(udev, 0);

if (usb_disable_ltm(udev)) {
dev_err(&udev->dev, "Failed to disable LTM before suspend\n");
@@ -3249,8 +3248,7 @@ int usb_port_suspend(struct usb_device *udev, pm_message_t msg)
usb_enable_ltm(udev);
err_ltm:
/* Try to enable USB2 hardware LPM again */
- if (udev->usb2_hw_lpm_capable == 1)
- usb_set_usb2_hardware_lpm(udev, 1);
+ usb_set_usb2_hardware_lpm(udev, 1);

if (udev->do_remote_wakeup)
(void) usb_disable_remote_wakeup(udev);
@@ -3533,9 +3531,7 @@ int usb_port_resume(struct usb_device *udev, pm_message_t msg)
hub_port_logical_disconnect(hub, port1);
} else {
/* Try to enable USB2 hardware LPM */
- if (udev->usb2_hw_lpm_capable == 1 &&
- !udev->usb2_hw_lpm_enabled)
- usb_set_usb2_hardware_lpm(udev, 1);
+ usb_set_usb2_hardware_lpm(udev, 1);

/* Try to enable USB3 LTM */
usb_enable_ltm(udev);
@@ -5639,8 +5635,7 @@ static int usb_reset_and_verify_device(struct usb_device *udev)
/* Disable USB2 hardware LPM.
* It will be re-enabled by the enumeration process.
*/
- if (udev->usb2_hw_lpm_enabled == 1)
- usb_set_usb2_hardware_lpm(udev, 0);
+ usb_set_usb2_hardware_lpm(udev, 0);

/* Disable LPM while we reset the device and reinstall the alt settings.
* Device-initiated LPM, and system exit latency settings are cleared
diff --git a/drivers/usb/core/message.c b/drivers/usb/core/message.c
index bfa5eda0cc26..a00952bdf645 100644
--- a/drivers/usb/core/message.c
+++ b/drivers/usb/core/message.c
@@ -1243,8 +1243,7 @@ void usb_disable_device(struct usb_device *dev, int skip_ep0)
dev->actconfig->interface[i] = NULL;
}

- if (dev->usb2_hw_lpm_enabled == 1)
- usb_set_usb2_hardware_lpm(dev, 0);
+ usb_set_usb2_hardware_lpm(dev, 0);
usb_unlocked_disable_lpm(dev);
usb_disable_ltm(dev);

--
2.17.1
\
 
 \ /
  Last update: 2018-12-03 09:33    [W:0.037 / U:2.156 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site