lkml.org 
[lkml]   [2018]   [Dec]   [20]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v3 6/7] arm64: dts: xilinx: ultra96: Standardize LED labels and triggers
On Mon, Oct 29, 2018 at 03:12:44PM +0530, Manivannan Sadhasivam wrote:
> For all 96Boards, the following standard is used for onboard LEDs.
>
> green:user1 default-trigger: heartbeat
> green:user2 default-trigger: mmc0/disk-activity(onboard-storage)
> green:user3 default-trigger: mmc1 (SD-card)
> green:user4 default-trigger: none, panic-indicator
> yellow:wlan default-trigger: phy0tx
> blue:bt default-trigger: hci0-power
>
> So lets adopt the same for Ultra96, which is one of the 96Boards
> CE and AI platform. Since the WLAN and BT LEDs are hardwired onboard,
> consolidate only User LEDs.
>

Hello,

Any update on this patch?

Regards,
Mani

> Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
> ---
> arch/arm64/boot/dts/xilinx/zynqmp-zcu100-revC.dts | 15 ++++++++-------
> 1 file changed, 8 insertions(+), 7 deletions(-)
>
> diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu100-revC.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu100-revC.dts
> index eb5e8bddb610..c08a8753215b 100644
> --- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu100-revC.dts
> +++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu100-revC.dts
> @@ -57,29 +57,30 @@
> leds {
> compatible = "gpio-leds";
> ds2 {
> - label = "ds2";
> + label = "green:user1";
> gpios = <&gpio 20 GPIO_ACTIVE_HIGH>;
> linux,default-trigger = "heartbeat";
> };
>
> ds3 {
> - label = "ds3";
> + label = "green:user2";
> gpios = <&gpio 19 GPIO_ACTIVE_HIGH>;
> - linux,default-trigger = "phy0tx"; /* WLAN tx */
> + linux,default-trigger = "mmc0";
> default-state = "off";
> };
>
> ds4 {
> - label = "ds4";
> + label = "green:user3";
> gpios = <&gpio 18 GPIO_ACTIVE_HIGH>;
> - linux,default-trigger = "phy0rx"; /* WLAN rx */
> + linux,default-trigger = "mmc1";
> default-state = "off";
> };
>
> ds5 {
> - label = "ds5";
> + label = "green:user4";
> gpios = <&gpio 17 GPIO_ACTIVE_HIGH>;
> - linux,default-trigger = "bluetooth-power";
> + linux,default-trigger = "none";
> + panic-indicator;
> };
>
> vbus_det { /* U5 USB5744 VBUS detection via MIO25 */
> --
> 2.17.1
>

\
 
 \ /
  Last update: 2018-12-21 03:37    [W:0.184 / U:0.068 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site