lkml.org 
[lkml]   [2018]   [Dec]   [18]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v3 00/15] ARM: sunxi: Enable Broadcom-based Bluetooth controllers
From
Date
Hi Chen-Yu,

> This is v3 of my Broadcom-based Bluetooth controllers on Allwinner SoC-
> based SBCs series. v2 was sent on 11/15, with a follow up ping on 11/28.
> No response from either Bluetooth maintainer. Would the maintainers
> acknowledge or provide feedback so we can move forward? WiFi for the
> Broadcom chips has been supported and enabled for many years. Bluetooth
> on the other hand has required userspace trickery to get it working.
> With serdev support, this now requires minimal interaction from
> users to get working.
>
>
> Changes since v2:
>
> - Collected tags from Ondrej for applicable patches
>
> Changes since v1:
>
> - Collected tags
> - Re-organize dt binding clocks and clock-names properties
> - Simplify check for deferred probe when getting clocks
> - Add explanation of Cubietruck's clk_out_a pinmux setting placement
> to commit message.
> - Add missing "uart-has-rtscts" property to Cubietruck device tree
>
> Original cover letter follows.
>
>
> On many Allwinner SBCs / developer boards, there is a WiFi+BT combo
> module from AMPAK. Inside is either one or two Broadcom chips, depending
> on the model. This series enables the Bluetooth controllers for AMPAK
> AP6210, AP6212, and AP6330 found on several boards. More will come later
> as other SoCs require changes to some other parts. I did not cover the
> SCO PCM connections from the controller to the SoC's I2S interface. It
> seems no one is actually doing this, so I was not sure how to proceed.
> Any suggestions?
>
> I deliberately left out the netdev mailing list and Dave Miller, as the
> only thing that is under net is the binding document. Maybe we should
> move that out of Documentation/devicetree/bindings/net/ ?
>
> Also, I'm not subscribed to the linux-bluetooth ML, so please CC me for
> any discussions.
>
> Patches 1 through 4 are device tree binding changes:
>
> 1 - Make the external clock name unambiguous, and add a second entry for
> the LPO clock.
>
> 2 - Add regulator supply properties for the VBAT and VDDIO power pins.
>
> 3 - Add a compatible string for BCM20702A1.
>
> 4 - Add a compatible string for BCM4330.
>
> Patches 5 through 13 are changes to the driver, either improvements,
> or updates to handle the updated device tree binding.
>
> 5 - Make the driver handle deferred probing for the external clock.
>
> 6 - Simplify clock error checking for subsequent clk API calls.
>
> 7 - Handle clock-names for the main external clock.
>
> 8 - Support a new external clock, the LPO.
>
> 9 - Support regulator supplies.
>
> 10 - Wait a small amount of time after toggling the GPIO for the device
> to settle.
>
> 11 - Add support for BCM20702A1, including its default address.
>
> 12 - Add BCM4330 compatible string to the driver.
>
> 13 - Handle default address for BCM43430A0.
>
> 14 - Enable Broadcom-based serdev Bluetooth for multiple Allwinner ARMv7
> boards.
>
> 15 - Enable Broadcom-based serdev Bluetooth for the Bananapi M64.
>
> checkpatch reports an error for both patch 11 and patch 13:
>
> ERROR: space required after that close brace '}'
>
> I followed the existing code's style. If this is undesirable, I can send
> a follow-up patch fixing the entire code block.
>
> The first 13 patches should go through the Bluetooth tree, while we, the
> sunxi maintainers, will take the last 2.
>
>
> Thanks
> ChenYu
>
> Chen-Yu Tsai (14):
> dt-bindings: net: broadcom-bluetooth: Fix external clock names
> dt-bindings: net: broadcom-bluetooth: Add VBAT and VDDIO supplies
> dt-bindings: net: broadcom-bluetooth: Add BCM20702A1 compatible string
> dt-bindings: net: broadcom-bluetooth: Add BCM4330 compatible string
> Bluetooth: hci_bcm: Handle deferred probing for the clock supply
> Bluetooth: hci_bcm: Simplify clk_get error handling
> Bluetooth: hci_bcm: Use "txco" and "extclk" to get clock reference
> Bluetooth: hci_bcm: Add support for LPO clock
> Bluetooth: hci_bcm: Add support for regulator supplies
> Bluetooth: hci_bcm: Wait for device to come out of reset after power
> on
> Bluetooth: hci_bcm: Add compatible string for BCM4330
> Bluetooth: btbcm: Add default address for BCM43430A0
> ARM: dts: sunxi: Enable Broadcom-based Bluetooth for multiple boards
> arm64: dts: allwinner: a64: bananapi-m64: Add Bluetooth device node
>
> Maxime Ripard (1):
> Bluetooth: hci_bcm: Add BCM20702A1 variant
>
> .../bindings/net/broadcom-bluetooth.txt | 11 +-
> arch/arm/boot/dts/sun7i-a20-cubietruck.dts | 25 ++++
> arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts | 18 +++
> .../boot/dts/sun8i-a83t-cubietruck-plus.dts | 18 +++
> arch/arm/boot/dts/sun8i-r16-bananapi-m2m.dts | 14 +++
> .../dts/allwinner/sun50i-a64-bananapi-m64.dts | 14 +++
> drivers/bluetooth/btbcm.c | 13 +-
> drivers/bluetooth/hci_bcm.c | 112 +++++++++++++++---
> 8 files changed, 208 insertions(+), 17 deletions(-)

patches 1-13 have been applied to bluetooth-next tree.

Regards

Marcel

\
 
 \ /
  Last update: 2018-12-19 00:51    [W:0.332 / U:0.044 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site