lkml.org 
[lkml]   [2018]   [Nov]   [9]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH 2/2] phy: qualcomm: Add Synopsys High-Speed USB PHY driver
On 08-11-18, 15:04, Shawn Guo wrote:
> +static int qcom_snps_hsphy_config_regulators(struct hsphy_priv *priv, int high)
> +{
> + int min, ret, i;
> +
> + min = high ? 1 : 0; /* low or none? */
> +
> + for (i = 0; i < VREG_NUM; i++) {
> + ret = regulator_set_voltage(priv->vregs[i].consumer,
> + priv->voltages[i][min],
> + priv->voltages[i][VOL_MAX]);
> + if (ret)
> + return ret;

should we not roll back the set voltages on error?

> +static int qcom_snps_hsphy_por_reset(struct hsphy_priv *priv)
> +{
> + int ret;
> +
> + ret = reset_control_assert(priv->por_reset);
> + if (ret)
> + return ret;
> +
> + /*
> + * The Femto PHY is POR reset in the following scenarios.

POR?

> +static int qcom_snps_hsphy_init(struct phy *phy)
> +{
> + struct hsphy_priv *priv = phy_get_drvdata(phy);
> + int state;
> + int ret;

perhaps they can be in a single line :)

> +static int qcom_snps_hsphy_probe(struct platform_device *pdev)
> +{
> + struct device *dev = &pdev->dev;
> + struct phy_provider *provider;
> + struct hsphy_priv *priv;
> + struct resource *res;
> + struct phy *phy;
> + int size;
> + int ret;
> + int i;
> +
> + priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
> + if (!priv)
> + return -ENOMEM;
> +
> + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> + priv->base = devm_ioremap_resource(dev, res);
> + if (IS_ERR(priv->base))
> + return PTR_ERR(priv->base);
> +
> + priv->num_clks = ARRAY_SIZE(qcom_snps_hsphy_clks);
> + priv->clks = devm_kcalloc(dev, priv->num_clks, sizeof(*priv->clks),
> + GFP_KERNEL);
> + if (!priv->clks)
> + return -ENOMEM;
> +
> + for (i = 0; i < priv->num_clks; i++)
> + priv->clks[i].id = qcom_snps_hsphy_clks[i];
> +
> + ret = devm_clk_bulk_get(dev, priv->num_clks, priv->clks);
> + if (ret)
> + return ret;
> +
> + priv->phy_reset = devm_reset_control_get(dev, "phy");
> + if (IS_ERR(priv->phy_reset))
> + return PTR_ERR(priv->phy_reset);
> +
> + priv->por_reset = devm_reset_control_get(dev, "por");
> + if (IS_ERR(priv->por_reset))
> + return PTR_ERR(priv->por_reset);
> +
> + priv->vregs[VDD].supply = "vdd";
> + priv->vregs[VDDA_1P8].supply = "vdda1p8";
> + priv->vregs[VDDA_3P3].supply = "vdda3p3";
> +
> + ret = devm_regulator_bulk_get(dev, VREG_NUM, priv->vregs);
> + if (ret)
> + return ret;
> +
> + priv->voltages[VDDA_1P8][VOL_NONE] = 0;
> + priv->voltages[VDDA_1P8][VOL_MIN] = 1800000;
> + priv->voltages[VDDA_1P8][VOL_MAX] = 1800000;
> +
> + priv->voltages[VDDA_3P3][VOL_NONE] = 0;
> + priv->voltages[VDDA_3P3][VOL_MIN] = 3050000;
> + priv->voltages[VDDA_3P3][VOL_MAX] = 3300000;
> +
> + ret = of_property_read_u32_array(dev->of_node, "qcom,vdd-voltage-level",
> + priv->voltages[VDD], VOL_NUM);
> + if (ret) {
> + dev_err(dev, "failed to read qcom,vdd-voltage-level\n");
> + return ret;
> + }
> +
> + size = of_property_count_u32_elems(dev->of_node, "qcom,init-seq");
> + if (size < 0)
> + size = 0;
> +
> + priv->init_seq = devm_kcalloc(dev, (size / 3) + 1,

size/3? I think it would be good to add a common explaining this
--
~Vinod

\
 
 \ /
  Last update: 2018-11-09 06:23    [W:0.160 / U:0.156 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site