lkml.org 
[lkml]   [2018]   [Nov]   [8]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRe: [PATCH v4 03/10] dt-bindings: spi: Adjust the bindings for the FSL QSPI driver
Date
On 08.11.18 09:41, Boris Brezillon wrote:
> On Wed, 7 Nov 2018 15:43:20 +0100
> Frieder Schrempf <frieder.schrempf@kontron.de> wrote:
>
>> From: Frieder Schrempf <frieder.schrempf@exceet.de>
>>
>> Adjust the documentation of the new SPI memory interface based
>> driver to reflect the new drivers settings.
>>
>> The "old" driver was using the "fsl,qspi-has-second-chip" property to
>> select one of two dual chip setups (two chips on one bus or two chips
>> on separate buses). And it used the order in which the subnodes are
>> defined in the dt to select the CS, the chip is connected to.
>>
>> Both methods are wrong and in fact the "reg" property should be used to
>> determine which bus and CS a chip is connected to. This also enables us
>> to use different setups than just single chip, or symmetric dual chip.
>>
>> So the porting of the driver from the MTD to the SPI framework actually
>> enforces the use of the "reg" properties and makes
>> "fsl,qspi-has-second-chip" superfluous.
>>
>> As all boards that have "fsl,qspi-has-second-chip" set, also have
>> correct "reg" properties, the removal of this property shouldn't lead to
>> any incompatibilities.
>>
>> The only compatibility issues I can see are with imx6sx-sdb.dts and
>> imx6sx-sdb-reva.dts, which have their reg properties set incorrectly
>> (see explanation here: [2]), all other boards should stay compatible.
>>
>> Also the "big-endian" flag was removed, as this setting is now selected
>> by the driver, depending on which SoC is in use.
>>
>> Signed-off-by: Frieder Schrempf <frieder.schrempf@exceet.de>
>> ---
>> .../devicetree/bindings/spi/spi-fsl-qspi.txt | 21 +++++++++-----------
>> 1 file changed, 9 insertions(+), 12 deletions(-)
>>
>> diff --git a/Documentation/devicetree/bindings/spi/spi-fsl-qspi.txt b/Documentation/devicetree/bindings/spi/spi-fsl-qspi.txt
>> index 483e9cf..6d7c9ec 100644
>> --- a/Documentation/devicetree/bindings/spi/spi-fsl-qspi.txt
>> +++ b/Documentation/devicetree/bindings/spi/spi-fsl-qspi.txt
>> @@ -3,9 +3,8 @@
>> Required properties:
>> - compatible : Should be "fsl,vf610-qspi", "fsl,imx6sx-qspi",
>> "fsl,imx7d-qspi", "fsl,imx6ul-qspi",
>> - "fsl,ls1021a-qspi"
>> + "fsl,ls1021a-qspi", "fsl,ls2080a-qspi"
>> or
>> - "fsl,ls2080a-qspi" followed by "fsl,ls1021a-qspi",
>
> Looks like this change is not related to this commit, and I'm not sure
> it's even needed. Plus, the order differs from the previous
> description, so, if the doc was right before this change it should be:
>
> "fsl,ls2080a-qspi", "fsl,ls1021a-qspi"

Right, there already was a discussion with Rob about that on v2 [1].
I forgot to drop this change.

[1] https://patchwork.ozlabs.org/patch/939868/

>> "fsl,ls1043a-qspi" followed by "fsl,ls1021a-qspi"
>> - reg : the first contains the register location and length,
>> the second contains the memory mapping address and length
>> @@ -14,15 +13,13 @@ Required properties:
>> - clocks : The clocks needed by the QuadSPI controller
>> - clock-names : Should contain the name of the clocks: "qspi_en" and "qspi".
>>
>> -Optional properties:
>> - - fsl,qspi-has-second-chip: The controller has two buses, bus A and bus B.
>> - Each bus can be connected with two NOR flashes.
>> - Most of the time, each bus only has one NOR flash
>> - connected, this is the default case.
>> - But if there are two NOR flashes connected to the
>> - bus, you should enable this property.
>> - (Please check the board's schematic.)
>> - - big-endian : That means the IP register is big endian
>> +Required SPI slave node properties:
>> + - reg: There are two buses (A and B) with two chip selects each.
>> + This encodes to which bus and CS the flash is connected:
>> + <0>: Bus A, CS 0
>> + <1>: Bus A, CS 1
>> + <2>: Bus B, CS 0
>> + <3>: Bus B, CS 1
>>
>> Example:
>>
>> @@ -40,7 +37,7 @@ qspi0: quadspi@40044000 {
>> };
>> };
>>
>> -Example showing the usage of two SPI NOR devices:
>> +Example showing the usage of two SPI NOR devices on bus A:
>>
>> &qspi2 {
>> pinctrl-names = "default";
>
\
 
 \ /
  Last update: 2018-11-08 09:49    [W:0.059 / U:2.040 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site