lkml.org 
[lkml]   [2018]   [Nov]   [7]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Date
SubjectRe: [RFC PATCH 01/12] dt-bindings: soc: qcom: add IPA bindings
On Tue, Nov 6, 2018 at 6:33 PM Alex Elder <elder@linaro.org> wrote:
>
> Add the binding definitions for the "qcom,ipa" and "qcom,rmnet-ipa"
> device tree nodes.
>
> Signed-off-by: Alex Elder <elder@linaro.org>
> ---
> .../devicetree/bindings/soc/qcom/qcom,ipa.txt | 136 ++++++++++++++++++
> .../bindings/soc/qcom/qcom,rmnet-ipa.txt | 15 ++
> 2 files changed, 151 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/soc/qcom/qcom,ipa.txt
> create mode 100644 Documentation/devicetree/bindings/soc/qcom/qcom,rmnet-ipa.txt
>
> diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,ipa.txt b/Documentation/devicetree/bindings/soc/qcom/qcom,ipa.txt
> new file mode 100644
> index 000000000000..d4d3d37df029
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/soc/qcom/qcom,ipa.txt
> @@ -0,0 +1,136 @@
> +Qualcomm IPA (IP Accelerator) Driver

Bindings are for h/w not drivers.

> +
> +This binding describes the Qualcomm IPA. The IPA is capable of offloading
> +certain network processing tasks (e.g. filtering, routing, and NAT) from
> +the main processor. The IPA currently serves only as a network interface,
> +providing access to an LTE network available via a modem.
> +
> +The IPA sits between multiple independent "execution environments,"
> +including the AP subsystem (APSS) and the modem. The IPA presents
> +a Generic Software Interface (GSI) to each execution environment.
> +The GSI is an integral part of the IPA, but it is logically isolated
> +and has a distinct interrupt and a separately-defined address space.
> +
> + ---------- ------------- ---------
> + | | |G| |G| | |
> + | APSS |===|S| IPA |S|===| Modem |
> + | | |I| |I| | |
> + ---------- ------------- ---------
> +
> +See also:
> + bindings/interrupt-controller/interrupts.txt
> + bindings/interconnect/interconnect.txt
> + bindings/soc/qcom/qcom,smp2p.txt
> + bindings/reserved-memory/reserved-memory.txt
> + bindings/clock/clock-bindings.txt
> +
> +All properties defined below are required.
> +
> +- compatible:
> + Must be one of the following compatible strings:
> + "qcom,ipa-sdm845-modem_init"
> + "qcom,ipa-sdm845-tz_init"

Normal order is <vendor>,<soc>-<ipblock>.

Don't use '_'.

What's the difference between these 2? It can't be detected somehow?
This might be better expressed as a property. Then if Trustzone
initializes things, it can just add a property.

> +
> +-reg:
> + Resources specyfing the physical address spaces of the IPA and GSI.

typo

> +
> +-reg-names:
> + The names of the address space ranges defined by the "reg" property.
> + Must be "ipa" and "gsi".
> +
> +- interrupts-extended:

Use 'interrupts' here and describe what they are and the order. What
they are connected to (and the need for interrupts-extended) is
outside the scope of this binding.

> + Specifies the IRQs used by the IPA. Four cells are required,
> + specifying: the IPA IRQ; the GSI IRQ; the clock query interrupt
> + from the modem; and the "ready for stage 2 initialization"
> + interrupt from the modem. The first two are hardware IRQs; the
> + third and fourth are SMP2P input interrupts.
> +
> +- interrupt-names:
> + The names of the interrupts defined by the "interrupts-extended"
> + property. Must be "ipa", "gsi", "ipa-clock-query", and
> + "ipa-post-init".

Format as one per line.

> +
> +- clocks:
> + Resource that defines the IPA core clock.
> +
> +- clock-names:
> + The name used for the IPA core clock. Must be "core".
> +
> +- interconnects:
> + Specifies the interconnects used by the IPA. Three cells are
> + required, specifying: the path from the IPA to memory; from
> + IPA to internal (SoC resident) memory; and between the AP
> + subsystem and IPA for register access.
> +
> +- interconnect-names:
> + The names of the interconnects defined by the "interconnects"
> + property. Must be "memory", "imem", and "config".
> +
> +- qcom,smem-states
> + The state bits used for SMP2P output. Two cells must be specified.
> + The first indicates whether the value in the second bit is valid
> + (1 means valid). The second, if valid, defines whether the IPA
> + clock is enabled (1 means enabled).
> +
> +- qcom,smem-state-names
> + The names of the state bits used for SMP2P output. These must be
> + "ipa-clock-enabled-valid" and "ipa-clock-enabled".
> +
> +- memory-region
> + A phandle for a reserved memory area that holds the firmware passed
> + to Trust Zone for authentication. (Note, this is required
> + only for "qcom,ipa-sdm845-tz_init".)
> +
> += EXAMPLE
> +
> +The following example represents the IPA present in the SDM845 SoC. It
> +shows portions of the "modem-smp2p" node to indicate its relationship
> +with the interrupts and SMEM states used by the IPA.
> +
> + modem-smp2p {
> + compatible = "qcom,smp2p";
> + . . .
> + ipa_smp2p_out: ipa-ap-to-modem {
> + qcom,entry-name = "ipa";
> + #qcom,smem-state-cells = <1>;
> + };
> +
> + ipa_smp2p_in: ipa-modem-to-ap {
> + qcom,entry-name = "ipa";
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + };
> + };
> +
> + ipa@1e00000 {

ipa@1e40000

> + compatible = "qcom,ipa-sdm845-modem_init";
> +
> + reg = <0x1e40000 0x34000>,
> + <0x1e04000 0x2c000>;
> + reg-names = "ipa",
> + "gsi";
> +
> + interrupts-extended = <&intc 0 311 IRQ_TYPE_LEVEL_HIGH>,
> + <&intc 0 432 IRQ_TYPE_LEVEL_HIGH>,
> + <&ipa_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
> + <&ipa_smp2p_in 1 IRQ_TYPE_EDGE_RISING>;
> + interrupt-names = "ipa",
> + "gsi",
> + "ipa-clock-query",
> + "ipa-post-init";
> +
> + clocks = <&rpmhcc RPMH_IPA_CLK>;
> + clock-names = "core";
> +
> + interconnects = <&qnoc MASTER_IPA &qnoc SLAVE_EBI1>,
> + <&qnoc MASTER_IPA &qnoc SLAVE_IMEM>,
> + <&qnoc MASTER_APPSS_PROC &qnoc SLAVE_IPA_CFG>;
> + interconnect-names = "memory",
> + "imem",
> + "config";
> +
> + qcom,smem-states = <&ipa_smp2p_out 0>,
> + <&ipa_smp2p_out 1>;
> + qcom,smem-state-names = "ipa-clock-enabled-valid",
> + "ipa-clock-enabled";
> + };
> diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,rmnet-ipa.txt b/Documentation/devicetree/bindings/soc/qcom/qcom,rmnet-ipa.txt
> new file mode 100644
> index 000000000000..3d0b2aabefc7
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/soc/qcom/qcom,rmnet-ipa.txt
> @@ -0,0 +1,15 @@
> +Qualcomm IPA RMNet Driver
> +
> +This binding describes the IPA RMNet driver, which is used to
> +represent virtual interfaces available on the modem accessed via
> +the IPA. Other than the compatible string there are no properties
> +associated with this device.
Only a compatible string is a sure sign this is not a h/w device and
you are just abusing DT to instantiate drivers. Make the IPA driver
instantiate any sub drivers it needs.

Rob

\
 
 \ /
  Last update: 2018-11-07 15:59    [W:0.290 / U:1.396 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site