lkml.org 
[lkml]   [2018]   [Nov]   [6]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [RFC PATCH v1 01/14] usb:cdns3: add pci to platform driver wrapper.
From
Date
Hi Pawel,

On 03/11/18 19:51, Pawel Laszczak wrote:
> Patch adds PCI specific glue drivier that creaties and registers in

s/drivier/driver
s/creaties/creates
s/in system/in-system

> system cdns-usb3 platform device. Thanks to that we will be able to use
> the cdns-usb3 platform driver for USBSS-DEV controller
> build on PCI board
>
> Signed-off-by: Pawel Laszczak <pawell@cadence.com>
> ---
> drivers/usb/Kconfig | 2 +
> drivers/usb/Makefile | 2 +
> drivers/usb/cdns3/Kconfig | 24 +++++
> drivers/usb/cdns3/Makefile | 3 +
> drivers/usb/cdns3/cdns3-pci-wrap.c | 162 +++++++++++++++++++++++++++++
> 5 files changed, 193 insertions(+)
> create mode 100644 drivers/usb/cdns3/Kconfig
> create mode 100644 drivers/usb/cdns3/Makefile
> create mode 100644 drivers/usb/cdns3/cdns3-pci-wrap.c
>
> diff --git a/drivers/usb/Kconfig b/drivers/usb/Kconfig
> index 987fc5ba6321..5f9334019d04 100644
> --- a/drivers/usb/Kconfig
> +++ b/drivers/usb/Kconfig
> @@ -112,6 +112,8 @@ source "drivers/usb/usbip/Kconfig"
>
> endif
>
> +source "drivers/usb/cdns3/Kconfig"
> +
> source "drivers/usb/mtu3/Kconfig"
>
> source "drivers/usb/musb/Kconfig"
> diff --git a/drivers/usb/Makefile b/drivers/usb/Makefile
> index 7d1b8c82b208..82093a60ea2c 100644
> --- a/drivers/usb/Makefile
> +++ b/drivers/usb/Makefile
> @@ -8,6 +8,8 @@
> obj-$(CONFIG_USB) += core/
> obj-$(CONFIG_USB_SUPPORT) += phy/
>
> +obj-$(CONFIG_USB_CDNS3) += cdns3/
> +
> obj-$(CONFIG_USB_DWC3) += dwc3/
> obj-$(CONFIG_USB_DWC2) += dwc2/
> obj-$(CONFIG_USB_ISP1760) += isp1760/
> diff --git a/drivers/usb/cdns3/Kconfig b/drivers/usb/cdns3/Kconfig
> new file mode 100644
> index 000000000000..888458372adb
> --- /dev/null
> +++ b/drivers/usb/cdns3/Kconfig
> @@ -0,0 +1,24 @@
> +config USB_CDNS3
> + tristate "Cadence USB3 Dual-Role Controller"
> + depends on ((USB_XHCI_HCD && USB_GADGET) || (USB_XHCI_HCD && !USB_GADGET) || (!USB_XHCI_HCD && USB_GADGET)) && HAS_DMA

Why not depend on USB instead of USB_XHCI_HCD?

> + help
> + Say Y here if your system has a cadence USB3 dual-role controller.
> + It supports: dual-role switch Host-only, and Peripheral-only.

Need a coma between switch and Host-only.

> +
> + If you choose to build this driver is a dynamically linked
> + module, the module will be called cdns3.ko.
> +
> +if USB_CDNS3
> +
> +config USB_CDNS3_PCI_WRAP
> + tristate "PCIe-based Platforms"
> + depends on USB_PCI && ACPI
> + default USB_CDNS3
> + help
> + If you're using the USBSS Core IP with a PCIe, please say
> + 'Y' or 'M' here.
> +
> + If you choose to build this driver as module it will
> + be dynamically linked and module will be called cdns3-pci.ko
> +
> +endif
> diff --git a/drivers/usb/cdns3/Makefile b/drivers/usb/cdns3/Makefile
> new file mode 100644
> index 000000000000..dcdd62003c6a
> --- /dev/null
> +++ b/drivers/usb/cdns3/Makefile
> @@ -0,0 +1,3 @@
> +obj-$(CONFIG_USB_CDNS3_PCI_WRAP) += cdns3-pci.o
> +
> +cdns3-pci-y := cdns3-pci-wrap.o
> diff --git a/drivers/usb/cdns3/cdns3-pci-wrap.c b/drivers/usb/cdns3/cdns3-pci-wrap.c
> new file mode 100644
> index 000000000000..6c229ab6dffb
> --- /dev/null
> +++ b/drivers/usb/cdns3/cdns3-pci-wrap.c
> @@ -0,0 +1,162 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Cadence USBSS PCI Glue driver
> + *
> + * Copyright (C) 2018 Cadence.
> + *
> + * Author: Pawel Laszczak <pawell@cadence.com>
> + */
> +
> +#include <linux/kernel.h>
> +#include <linux/module.h>
> +#include <linux/pci.h>
> +#include <linux/platform_device.h>
> +#include <linux/dma-mapping.h>
> +#include <linux/slab.h>
> +
> +struct cdns3_wrap {
> + struct platform_device *plat_dev;
> + struct pci_dev *hg_dev;
> + struct resource dev_res[4];
> +};
> +
> +struct cdns3_wrap wrap;
> +
> +#define RES_IRQ_ID 0
> +#define RES_HOST_ID 1
> +#define RES_DEV_ID 2
> +#define RES_DRD_ID 3
> +
> +#define PCI_BAR_HOST 0
> +#define PCI_BAR_DEV 2
> +#define PCI_BAR_OTG 4
> +
> +#define PCI_DEV_FN_HOST_DEVICE 0
> +#define PCI_DEV_FN_OTG 1
> +
> +#define PCI_DRIVER_NAME "cdns3-pci-usbss"
> +#define PLAT_DRIVER_NAME "cdns-usb3"
> +
> +#define CDNS_VENDOR_ID 0x17cd
> +#define CDNS_DEVICE_ID 0x0100
> +
> +/**
> + * cdns3_pci_probe - Probe function for Cadence USB wrapper driver
> + * @pdev: platform device object
> + * @id: pci device id
> + *
> + * Returns 0 on success otherwise negative errno
> + */
> +static int cdns3_pci_probe(struct pci_dev *pdev,
> + const struct pci_device_id *id)
> +{
> + struct platform_device_info plat_info;
> + struct cdns3_wrap *wrap;
> + struct resource *res;
> + int err;
> +
> + /*
> + * for GADGET/HOST PCI (devfn) function number is 0,
> + * for OTG PCI (devfn) function number is 1
> + */
> + if (!id || pdev->devfn != PCI_DEV_FN_HOST_DEVICE)
> + return -EINVAL;
> +
> + err = pcim_enable_device(pdev);
> + if (err) {
> + dev_err(&pdev->dev, "Enabling PCI device has failed %d\n", err);
> + return err;
> + }
> +
> + pci_set_master(pdev);
> + wrap = devm_kzalloc(&pdev->dev, sizeof(*wrap), GFP_KERNEL);
> + if (!wrap) {
> + dev_err(&pdev->dev, "Failed to load PCI module\n");
> + return -ENOMEM;
> + }
> +
> + /* function 0: host(BAR_0) + device(BAR_1) + otg(BAR_2)). */
> + memset(wrap->dev_res, 0x00,
> + sizeof(struct resource) * ARRAY_SIZE(wrap->dev_res));
> + dev_info(&pdev->dev, "Initialize Device resources\n");
> + res = wrap->dev_res;
> +
> +#if IS_ENABLED(CONFIG_USB_CDNS3_GADGET)

Why depend on Config options to populate resources? The resources should be there regardless.
It is a lot simpler that way as it reflects the hardware as-is.

> + res[RES_DEV_ID].start = pci_resource_start(pdev, PCI_BAR_DEV);
> + res[RES_DEV_ID].end = pci_resource_end(pdev, PCI_BAR_DEV);
> + res[RES_DEV_ID].name = "cdns3-dev-regs";
> + res[RES_DEV_ID].flags = IORESOURCE_MEM;
> + dev_info(&pdev->dev, "USBSS-DEV physical base addr: %pa\n",
> + &res[RES_DEV_ID].start);
> +

dev_dbg() for this and all occurrences below?

> +#endif
> +
> +#if IS_ENABLED(CONFIG_USB_CDNS3_HOST)
> + res[RES_HOST_ID].start = pci_resource_start(pdev, PCI_BAR_HOST);
> + res[RES_HOST_ID].end = pci_resource_end(pdev, PCI_BAR_HOST);
> + res[RES_HOST_ID].name = "cdns3-xhci-regs";
> + res[RES_HOST_ID].flags = IORESOURCE_MEM;
> + dev_info(&pdev->dev, "USBSS-XHCI physical base addr: %pa\n",
> + &res[RES_HOST_ID].start);
> +#endif
> +
> + res[RES_DRD_ID].start = pci_resource_start(pdev, PCI_BAR_OTG);
> + res[RES_DRD_ID].end = pci_resource_end(pdev, PCI_BAR_OTG);
> + res[RES_DRD_ID].name = "cdns3-otg";
> + res[RES_DRD_ID].flags = IORESOURCE_MEM;
> + dev_info(&pdev->dev, "USBSS-DRD physical base addr: %pa\n",
> + &res[RES_DRD_ID].start);
> +
> + /* Interrupt common for both device and XHCI */
> + wrap->dev_res[RES_IRQ_ID].start = pdev->irq;
> + wrap->dev_res[RES_IRQ_ID].name = "cdns3-irq";
> + wrap->dev_res[RES_IRQ_ID].flags = IORESOURCE_IRQ;
> +
> + /* set up platform device info */
> + memset(&plat_info, 0, sizeof(plat_info));
> + plat_info.parent = &pdev->dev;
> + plat_info.fwnode = pdev->dev.fwnode;
> + plat_info.name = PLAT_DRIVER_NAME;
> + plat_info.id = pdev->devfn;
> + plat_info.res = wrap->dev_res;
> + plat_info.num_res = ARRAY_SIZE(wrap->dev_res);
> + plat_info.dma_mask = pdev->dma_mask;
> +
> + /* register platform device */
> + wrap->plat_dev = platform_device_register_full(&plat_info);
> + if (IS_ERR(wrap->plat_dev)) {
> + err = PTR_ERR(wrap->plat_dev);
> + return err;
> + }
> +
> + pci_set_drvdata(pdev, wrap);
> +
> + return err;
> +}
> +
> +void cdns3_pci_remove(struct pci_dev *pdev)
> +{
> + struct cdns3_wrap *wrap = (struct cdns3_wrap *)pci_get_drvdata(pdev);
> +
> + platform_device_unregister(wrap->plat_dev);
> +}
> +
> +static const struct pci_device_id cdns3_pci_ids[] = {
> + { PCI_DEVICE(CDNS_VENDOR_ID, CDNS_DEVICE_ID), },
> + { 0, }
> +};
> +
> +static struct pci_driver cdns3_pci_driver = {
> + .name = PCI_DRIVER_NAME,
> + .id_table = cdns3_pci_ids,
> + .probe = cdns3_pci_probe,
> + .remove = cdns3_pci_remove,
> +};
> +
> +module_pci_driver(cdns3_pci_driver);
> +MODULE_DEVICE_TABLE(pci, cdns3_pci_ids);
> +
> +MODULE_AUTHOR("Pawel Laszczak <pawell@cadence.com>");
> +MODULE_LICENSE("GPL v2");
> +MODULE_DESCRIPTION("Cadence USBSS PCI wrapperr");
> +
>

cheers,
-roger
--
Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki.
Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki

\
 
 \ /
  Last update: 2018-11-06 14:49    [W:0.334 / U:1.820 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site