lkml.org 
[lkml]   [2018]   [Nov]   [23]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH 2/6] phy: add A3700 COMPHY support
Hello,

+ Adding people concerned by this driver that I forgot when initially
sending the driver, will update the Cc: list if there is a v2.

One question below.

Miquel Raynal <miquel.raynal@bootlin.com> wrote on Thu, 22 Nov 2018
22:04:16 +0100:

> Add a driver to support COMPHY, a hardware block providing shared
> serdes PHYs on Marvell Armada 3700. This driver uses SMC calls and
> rely on having an up-to-date firmware.
>
> SATA, PCie and USB3 host mode have been tested successfully with an
> ESPRESSObin. SGMII mode cannot be tested with this platform.
>
> Co-Developed-by: Evan Wang <xswang@marvell.com>
> Signed-off-by: Evan Wang <xswang@marvell.com>
> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
> ---
> drivers/phy/marvell/Kconfig | 10 +
> drivers/phy/marvell/Makefile | 1 +
> drivers/phy/marvell/phy-mvebu-a3700-comphy.c | 276 +++++++++++++++++++
> 3 files changed, 287 insertions(+)
> create mode 100644 drivers/phy/marvell/phy-mvebu-a3700-comphy.c

[...]

> +
> +static int mvebu_a3700_comphy_power_on(struct phy *phy)
> +{
> + struct mvebu_a3700_comphy_lane *lane = phy_get_drvdata(phy);
> + u32 fw_param;
> + int fw_mode;
> +
> + fw_mode = mvebu_a3700_comphy_get_fw_mode(lane->id, lane->port,
> + lane->mode);
> + if (fw_mode < 0) {
> + dev_err(lane->dev, "invalid COMPHY mode\n");
> + return fw_mode;
> + }
> +
> + switch (lane->mode) {
> + case PHY_MODE_USB_HOST_SS:
> + dev_dbg(lane->dev, "set lane %d to USB3 host mode\n", lane->id);
> + fw_param = COMPHY_FW_MODE(fw_mode);
> + break;
> + case PHY_MODE_SATA:
> + dev_dbg(lane->dev, "set lane %d to SATA mode\n", lane->id);
> + fw_param = COMPHY_FW_MODE(fw_mode);
> + break;
> + case PHY_MODE_SGMII:
> + dev_dbg(lane->dev, "set lane %d to SGMII mode\n", lane->id);
> + fw_param = COMPHY_FW_NET(fw_mode, lane->port,
> + COMPHY_FW_SPEED_1_25G);
> + break;
> + case PHY_MODE_PCIE:
> + dev_dbg(lane->dev, "set lane %d to PCIe mode\n", lane->id);
> + fw_param = COMPHY_FW_PCIE(fw_mode, lane->port,
> + COMPHY_FW_SPEED_5G,
> + phy->attrs.bus_width);
> + break;
> + default:
> + dev_err(lane->dev, "unsupported PHY mode (%d)\n", lane->mode);
> + return -ENOTSUPP;
> + }
> +
> + return mvebu_a3700_comphy_smc(COMPHY_SIP_POWER_ON, lane->id, fw_param);

This call might fail because the firmware is not up-to-date. In this
case, I wonder what is the appropriate behavior. Here I just return the
error; this means drivers may fail to probe when enabling their PHY.

Shall I ignore a "not supported by the firmware" code and return 0 to
the caller (with a printed warning) so it will continue probing? Doing
so is lying as the PHY might not be configured as expected and S2RAM
will always fail in this case.

Thanks,
Miquèl

\
 
 \ /
  Last update: 2018-11-23 09:31    [W:0.061 / U:0.044 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site