lkml.org 
[lkml]   [2018]   [Nov]   [23]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v3 05/14] media: dt-bindings: marvell,mmp2-ccic: Add Marvell MMP2 camera
Hi Lubomir,

On Tue, Nov 20, 2018 at 11:03:10AM +0100, Lubomir Rintel wrote:
> Add Marvell MMP2 camera host interface.
>
> Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
>
> ---
> Changes since v2:
> - Added #clock-cells, clock-names, port
>
> .../bindings/media/marvell,mmp2-ccic.txt | 37 +++++++++++++++++++
> 1 file changed, 37 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/media/marvell,mmp2-ccic.txt
>
> diff --git a/Documentation/devicetree/bindings/media/marvell,mmp2-ccic.txt b/Documentation/devicetree/bindings/media/marvell,mmp2-ccic.txt
> new file mode 100644
> index 000000000000..e5e8ca90e7f7
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/media/marvell,mmp2-ccic.txt
> @@ -0,0 +1,37 @@
> +Marvell MMP2 camera host interface
> +
> +Required properties:
> + - compatible: Should be "marvell,mmp2-ccic"
> + - reg: register base and size
> + - interrupts: the interrupt number
> + - #clock-cells: must be 0
> + - any required generic properties defined in video-interfaces.txt

I don't think video-interfaces applies here. It described bindings to
be used for endpoint and port nodes.

> +
> +Optional properties:
> + - clocks: input clock (see clock-bindings.txt)

What do you think of:
"reference to the input clock as specified by clock-bindings.txt"

> + - clock-names: names of the clocks used, may include "axi", "func" and
> + "phy"

"may include" is abit vague. Which clock should the interface be
powered from, and in which case?

> + - clock-output-names: should contain the name of the clock driving the
> + sensor master clock MCLK

This is a property for the clock provider part, and I will just list
the only clock this interfaces provides here:

- clock-output-names: Optional clock source for sensors. Shall be "mclk".

See a comment on patch 14 on the use of the clock provider part.

> +
> +Required subnodes:
> + - port: the parallel bus interface port with a single endpoint linked to
> + the sensor's endpoint as described in video-interfaces.txt
> +
> +Example:
> +
> + camera0: camera@d420a000 {
> + compatible = "marvell,mmp2-ccic";
> + reg = <0xd420a000 0x800>;
> + interrupts = <42>;
> + clocks = <&soc_clocks MMP2_CLK_CCIC0>;
> + clock-names = "axi";
> + #clock-cells = <0>;
> + clock-output-names = "mclk";
> +
> + port {
> + camera0_0: endpoint {
> + remote-endpoint = <&ov7670_0>;

I'm debated, your sensor does not support configuring the parallel bus,
that's fine, but as "bindings describe hardware" shouldn't you list
here the bus configurations the HW interface supports and list their default
values? Or there are none for real in this platform?

Thanks
j


> + };
> + };
> + };
> --
> 2.19.1
>
[unhandled content-type:application/pgp-signature]
\
 
 \ /
  Last update: 2018-11-22 22:07    [W:0.112 / U:0.024 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site