lkml.org 
[lkml]   [2018]   [Nov]   [19]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH 2/2] dt-binding: spi: Document Renesas R-Car RPC controller bindings
From
Date
On 11/19/2018 11:01 AM, Mason Yang wrote:
> Document the bindings used by the Renesas R-Car D3 RPC controller.
>
> Signed-off-by: Mason Yang <masonccyang@mxic.com.tw>
> ---
> .../devicetree/bindings/spi/spi-renesas-rpc.txt | 33 ++++++++++++++++++++++
> 1 file changed, 33 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/spi/spi-renesas-rpc.txt
>
> diff --git a/Documentation/devicetree/bindings/spi/spi-renesas-rpc.txt b/Documentation/devicetree/bindings/spi/spi-renesas-rpc.txt
> new file mode 100644
> index 0000000..8286cc8
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/spi/spi-renesas-rpc.txt
> @@ -0,0 +1,33 @@
> +Renesas R-Car D3 RPC controller Device Tree Bindings
> +----------------------------------------------------
> +
> +Required properties:
> +- compatible: should be "renesas,rpc-r8a77995"
> +- #address-cells: should be 1
> +- #size-cells: should be 0
> +- reg: should contain 2 entries, one for the registers and one for the direct
> + mapping area
> +- reg-names: should contain "rpc_regs" and "dirmap"
> +- interrupts: interrupt line connected to the RPC SPI controller

Do you also plan to support the RPC HF mode ? And if so, how would that
look in the bindings ? I'd like to avoid having to redesign the bindings
later to handle both the SPI and HF modes.

The HF is roughly a CFI flash with different bus interface.

btw U-Boot has drivers for both the HF and SPI mode:
http://git.denx.de/?p=u-boot.git;a=blob;f=drivers/mtd/renesas_rpc_hf.c
http://git.denx.de/?p=u-boot.git;a=blob;f=drivers/spi/renesas_rpc_spi.c

> +- clock-names: should contain "clk_rpc"
> +- clocks: should contain 1 entries for the CPG Module 917 clocks
> +
> +Example:
> +
> + rpc: spi@ee200000 {
> + compatible = "renesas,rpc-r8a77995";
> + reg = <0 0xee200000 0 0x8100>, <0 0x08000000 0 0x4000000>;
> + reg-names = "rpc_regs", "dirmap";
> + clocks = <&cpg CPG_MOD 917>;
> + clock-names = "clk_rpc";
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + flash@0 {
> + compatible = "jedec,spi-nor";
> + reg = <0>;
> + spi-max-frequency = <40000000>;
> + spi-tx-bus-width = <1>;
> + spi-rx-bus-width = <1>;
> + };
> + };
>


--
Best regards,
Marek Vasut

\
 
 \ /
  Last update: 2018-11-19 14:50    [W:0.209 / U:2.408 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site