lkml.org 
[lkml]   [2018]   [Nov]   [19]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH v4 1/2] gpio: Add driver for PC Engines APU boards
On Thu, Nov 15, 2018 at 2:32 PM Florian Eckert <fe@dev.tdt.de> wrote:

> Add a new device driver "gpio-apu" which will handle the GPIOs on APU2
> and APU3 devices from PC Engines.
>
> APU2 (https://pcengines.ch/schema/apu2c.pdf page 7):
> - G32 is "button_reset" connected to the smd-button on the frontpanel
> - G50 is "mpcie2_reset" connected to mPCIe2 reset line
> - G51 is "mpcie3_reset" connected to mPCIe3 reset line
>
> APU3 (https://pcengines.ch/schema/apu3c.pdf page 7):
> - G32 is "button_reset" connected to the smd-button on the frontpanel
> - G50 is "mpcie2_reset" connected to mPCIe2 reset line
> - G51 is "mpcie3_reset" connected to mPCIe3 reset line
> - G33 is "simswap" connected to SIM switch IC to swap the SIM between
> mPCIe2 and mPCIe3 slot
>
> Signed-off-by: Florian Eckert <fe@dev.tdt.de>

This is looking better and better! Thanks to everyone helping out
and thanks for your perseverance Florian!

> +config GPIO_APU
> + tristate "PC Engines APU2/APU3 GPIO support"
> + depends on X86
> + select GPIO_GENERIC

Excellent idea.

But it seems you are not using this. You would be using
it if you used bgpio_init() but if I understand correctly this
driver cannot use that because this GPIO is something like
one register per pin, correct?

Let me suggest:

> +struct apu_gpio_pdata {
> + struct platform_device *pdev;
> + struct gpio_chip *chip;

Make that a real member of this struct and not a pointer.
I.e. just remove the "*".

> +static struct apu_gpio_pdata *apu_gpio;

Why a static local? It seems you can just pass around
the pointer.

> +static int gpio_apu_get_dir(struct gpio_chip *chip, unsigned int offset)
> +{
> + u32 val;
> +
> + spin_lock(&apu_gpio->lock);
> +
> + val = ~ioread32(apu_gpio->addr[offset]);
> + val = (val >> APU_GPIO_BIT_DIR) & 1;

I would just:

#include <linux/bits.h>

val = ~ioread32(apu_gpio->addr[offset]);
spin_unlock();

return !!(val & BIT(APU_GPIO_BIT_DIR));

This clamps the value to [0,1] in a nice way.

> +static int gpio_apu_get_data(struct gpio_chip *chip, unsigned int offset)
> +{
> + u32 val;
> +
> + spin_lock(&apu_gpio->lock);
> +
> + val = ioread32(apu_gpio->addr[offset]);
> +
> + spin_unlock(&apu_gpio->lock);
> +
> + return (val >> APU_GPIO_BIT_RD) & 1;

return !!(val & BIT(APU_GPIO_BIT_RD));

> + return devm_gpiochip_add_data(&pdev->dev, apu_gpio->chip, NULL);

Instead of passing NULL pas apu_gpio as the last argument and in
all callbacks you can use:

struct apu_gpio_pdata *apu_gpio = gpiochip_get_data(gc);

To get a pointer to the per-instance state container.

Yours,
Linus Walleij

\
 
 \ /
  Last update: 2018-11-19 14:47    [W:0.041 / U:1.012 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site