lkml.org 
[lkml]   [2018]   [Nov]   [18]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[RFC PATCH v2 02/15] usb:cdns3: Device side header file.
Date
Patch defines macros used by device side of controller,
structures holding registers, and some other
object used by device controller.

Signed-off-by: Pawel Laszczak <pawell@cadence.com>
---
drivers/usb/cdns3/gadget.h | 1071 ++++++++++++++++++++++++++++++++++++
1 file changed, 1071 insertions(+)
create mode 100644 drivers/usb/cdns3/gadget.h

diff --git a/drivers/usb/cdns3/gadget.h b/drivers/usb/cdns3/gadget.h
new file mode 100644
index 000000000000..75ca6214e79a
--- /dev/null
+++ b/drivers/usb/cdns3/gadget.h
@@ -0,0 +1,1071 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * USBSS device controller driver
+ *
+ * Copyright (C) 2018 Cadence.
+ * Copyright (C) 2018 NXP
+ *
+ * Author: Pawel Laszczak <pawell@cadence.com>
+ * Pawel Jez <pjez@cadence.com>
+ * Peter Chen <peter.chen@nxp.com>
+ */
+#ifndef __LINUX_CDNS3_GADGET
+#define __LINUX_CDNS3_GADGET
+#include <linux/usb/gadget.h>
+
+/*
+ * USBSS-DEV register interface.
+ * This corresponds to the USBSS Device Controller Interface
+ */
+
+/**
+ * struct xhci_cap_regs - xHCI Host Controller Capability Registers.
+ * @usb_conf: Global Configuration Register.
+ * @usb_sts: Global Status Register.
+ * @usb_cmd: Global Command Register.
+ * @usb_iptn: ITP/SOF number Register.
+ * @usb_lpm: Global Command Register.
+ * @usb_ien: USB Interrupt Enable Register.
+ * @usb_ists: USB Interrupt Status Register.
+ * @ep_sel: Endpoint Select Register.
+ * @ep_traddr: Endpoint Transfer Ring Address Register.
+ * @ep_cfg: Endpoint Configuration Register.
+ * @ep_cmd: Endpoint Command Register.
+ * @ep_sts: Endpoint Status Register.
+ * @ep_sts_sid: Endpoint Status Register.
+ * @ep_sts_en: Endpoint Status Register Enable.
+ * @drbl: Doorbell Register.
+ * @ep_ien: EP Interrupt Enable Register.
+ * @ep_ists: EP Interrupt Status Register.
+ * @usb_pwr: Global Power Configuration Register.
+ * @usb_conf2: Global Configuration Register 2.
+ * @usb_cap1: Capability Register 1.
+ * @usb_cap2: Capability Register 2.
+ * @usb_cap3: Capability Register 3.
+ * @usb_cap4: Capability Register 4.
+ * @usb_cap5: Capability Register 5.
+ * @usb_cap6: Capability Register 6.
+ * @usb_cpkt1: Custom Packet Register 1.
+ * @usb_cpkt2: Custom Packet Register 2.
+ * @usb_cpkt3: Custom Packet Register 3.
+ * @reserved1: Reserved.
+ * @cfg_regs: Configuration registers.
+ * @reserved2: Reserved.
+ * @dma_axi_ctrl: AXI Control register.
+ * @dma_axi_id: AXI ID register.
+ * @dma_axi_cap: AXI Capability register.
+ * @dma_axi_ctrl0: AXI Control 0 register.
+ * @dma_axi_ctrl1: AXI Control 1 register.
+ */
+struct cdns3_usb_regs {
+ __le32 usb_conf;
+ __le32 usb_sts;
+ __le32 usb_cmd;
+ __le32 usb_iptn;
+ __le32 usb_lpm;
+ __le32 usb_ien;
+ __le32 usb_ists;
+ __le32 ep_sel;
+ __le32 ep_traddr;
+ __le32 ep_cfg;
+ __le32 ep_cmd;
+ __le32 ep_sts;
+ __le32 ep_sts_sid;
+ __le32 ep_sts_en;
+ __le32 drbl;
+ __le32 ep_ien;
+ __le32 ep_ists;
+ __le32 usb_pwr;
+ __le32 usb_conf2;
+ __le32 usb_cap1;
+ __le32 usb_cap2;
+ __le32 usb_cap3;
+ __le32 usb_cap4;
+ __le32 usb_cap5;
+ __le32 usb_cap6;
+ __le32 usb_cpkt1;
+ __le32 usb_cpkt2;
+ __le32 usb_cpkt3;
+ __le32 reserved1[36];
+ __le32 cfg_reg1;
+ __le32 dbg_link1;
+ __le32 dbg_link2;
+ __le32 cfg_regs[74];
+ __le32 reserved2[34];
+ __le32 dma_axi_ctrl;
+ __le32 dma_axi_id;
+ __le32 dma_axi_cap;
+ __le32 dma_axi_ctrl0;
+ __le32 dma_axi_ctrl1;
+};
+
+/* USB_CONF - bitmasks */
+/* Reset USB device configuration. */
+#define USB_CONF_CFGRST BIT(0)
+/* Set Configuration. */
+#define USB_CONF_CFGSET BIT(1)
+/* Disconnect USB device in SuperSpeed. */
+#define USB_CONF_USB3DIS BIT(3)
+/* Disconnect USB device in HS/FS */
+#define USB_CONF_USB2DIS BIT(4)
+/* Little Endian access - default */
+#define USB_CONF_LENDIAN BIT(5)
+/*
+ * Big Endian access. Driver assume that byte order for
+ * SFRs access always is as Little Endian so this bit
+ * is not used.
+ */
+#define USB_CONF_BENDIAN BIT(6)
+/* Device software reset. */
+#define USB_CONF_SWRST BIT(7)
+/* Singular DMA transfer mode. */
+#define USB_CONF_DSING BIT(8)
+/* Multiple DMA transfers mode. */
+#define USB_CONF_DMULT BIT(9)
+/* DMA clock turn-off enable. */
+#define USB_CONF_DMAOFFEN BIT(10)
+/* DMA clock turn-off disable. */
+#define USB_CONF_DMAOFFDS BIT(11)
+/* Clear Force Full Speed. */
+#define USB_CONF_CFORCE_FS BIT(12)
+/* Set Force Full Speed. */
+#define USB_CONF_SFORCE_FS BIT(13)
+/* Device enable. */
+#define USB_CONF_DEVEN BIT(14)
+/* Device disable. */
+#define USB_CONF_DEVDS BIT(15)
+/* L1 LPM state entry enable (used in HS/FS mode). */
+#define USB_CONF_L1EN BIT(16)
+/* L1 LPM state entry disable (used in HS/FS mode). */
+#define USB_CONF_L1DS BIT(17)
+/* USB 2.0 clock gate disable. */
+#define USB_CONF_CLK2OFFEN BIT(18)
+/* USB 2.0 clock gate enable. */
+#define USB_CONF_CLK2OFFDS BIT(19)
+/* L0 LPM state entry request (used in HS/FS mode). */
+#define USB_CONF_LGO_L0 BIT(20)
+/* USB 3.0 clock gate disable. */
+#define USB_CONF_CLK3OFFEN BIT(21)
+/* USB 3.0 clock gate enable. */
+#define USB_CONF_CLK3OFFDS BIT(22)
+/* Bit 23 is reserved*/
+/* U1 state entry enable (used in SS mode). */
+#define USB_CONF_U1EN BIT(24)
+/* U1 state entry disable (used in SS mode). */
+#define USB_CONF_U1DS BIT(25)
+/* U2 state entry enable (used in SS mode). */
+#define USB_CONF_U2EN BIT(26)
+/* U2 state entry disable (used in SS mode). */
+#define USB_CONF_U2DS BIT(27)
+/* U0 state entry request (used in SS mode). */
+#define USB_CONF_LGO_U0 BIT(28)
+/* U1 state entry request (used in SS mode). */
+#define USB_CONF_LGO_U1 BIT(29)
+/* U2 state entry request (used in SS mode). */
+#define USB_CONF_LGO_U2 BIT(30)
+/* SS.Inactive state entry request (used in SS mode) */
+#define USB_CONF_LGO_SSINACT BIT(31)
+
+/* USB_STS - bitmasks */
+/*
+ * Configuration status.
+ * 1 - device is in the configured state.
+ * 0 - device is not configured.
+ */
+#define USB_STS_CFGSTS_MASK BIT(0)
+#define USB_STS_CFGSTS(p) ((p) & USB_STS_CFGSTS_MASK)
+/*
+ * On-chip memory overflow.
+ * 0 - On-chip memory status OK.
+ * 1 - On-chip memory overflow.
+ */
+#define USB_STS_OV_MASK BIT(1)
+#define USB_STS_OV(p) ((p) & USB_STS_OV_MASK)
+/*
+ * SuperSpeed connection status.
+ * 0 - USB in SuperSpeed mode disconnected.
+ * 1 - USB in SuperSpeed mode connected.
+ */
+#define USB_STS_USB3CONS_MASK BIT(2)
+#define USB_STS_USB3CONS(p) ((p) & USB_STS_USB3CONS_MASK)
+/*
+ * DMA transfer configuration status.
+ * 0 - single request.
+ * 1 - multiple TRB chain
+ */
+#define USB_STS_DTRANS_MASK BIT(3)
+#define USB_STS_DTRANS(p) ((p) & USB_STS_DTRANS_MASK)
+/*
+ * Device speed.
+ * 0 - Undefined (value after reset).
+ * 1 - Low speed
+ * 2 - Full speed
+ * 3 - High speed
+ * 4 - Super speed
+ */
+#define USB_STS_USBSPEED_MASK GENMASK(6, 4)
+#define USB_STS_USBSPEED(p) (((p) & USB_STS_USBSPEED_MASK) >> 4)
+#define USB_STS_LS (0x1 << 4)
+#define USB_STS_FS (0x2 << 4)
+#define USB_STS_HS (0x3 << 4)
+#define USB_STS_SS (0x4 << 4)
+#define DEV_UNDEFSPEED(p) (((p) & USB_STS_USBSPEED_MASK) == (0x0 << 4))
+#define DEV_LOWSPEED(p) (((p) & USB_STS_USBSPEED_MASK) == USB_STS_LS)
+#define DEV_FULLSPEED(p) (((p) & USB_STS_USBSPEED_MASK) == USB_STS_FS)
+#define DEV_HIGHSPEED(p) (((p) & USB_STS_USBSPEED_MASK) == USB_STS_HS)
+#define DEV_SUPERSPEED(p) (((p) & USB_STS_USBSPEED_MASK) == USB_STS_SS)
+/*
+ * Endianness for SFR access.
+ * 0 - Little Endian order (default after hardware reset).
+ * 1 - Big Endian order
+ */
+#define USB_STS_ENDIAN_MASK BIT(7)
+#define USB_STS_ENDIAN(p) ((p) & USB_STS_ENDIAN_MASK)
+/*
+ * HS/FS clock turn-off status.
+ * 0 - hsfs clock is always on.
+ * 1 - hsfs clock turn-off in L2 (HS/FS mode) is enabled
+ * (default after hardware reset).
+ */
+#define USB_STS_CLK2OFF_MASK BIT(8)
+#define USB_STS_CLK2OFF(p) ((p) & USB_STS_CLK2OFF_MASK)
+/*
+ * PCLK clock turn-off status.
+ * 0 - pclk clock is always on.
+ * 1 - pclk clock turn-off in U3 (SS mode) is enabled
+ * (default after hardware reset).
+ */
+#define USB_STS_CLK3OFF_MASK BIT(9)
+#define USB_STS_CLK3OFF(p) ((p) & USB_STS_CLK3OFF_MASK)
+/*
+ * Controller in reset state.
+ * 0 - Internal reset is active.
+ * 1 - Internal reset is not active and controller is fully operational.
+ */
+#define USB_STS_IN_RST_MASK BIT(10)
+#define USB_STS_IN_RST(p) ((p) & USB_STS_IN_RST_MASK)
+/*
+ * Device enable Status.
+ * 0 - USB device is disabled (VBUS input is disconnected from internal logic).
+ * 1 - USB device is enabled (VBUS input is connected to the internal logic).
+ */
+#define USB_STS_DEVS_MASK BIT(14)
+#define USB_STS_DEVS(p) ((p) & USB_STS_DEVS_MASK)
+/*
+ * DAddress statuss.
+ * 0 - USB device is default state.
+ * 1 - USB device is at least in address state.
+ */
+#define USB_STS_ADDRESSED_MASK BIT(15)
+#define USB_STS_ADDRESSED(p) ((p) & USB_STS_ADDRESSED_MASK)
+/*
+ * L1 LPM state enable status (used in HS/FS mode).
+ * 0 - Entering to L1 LPM state disabled.
+ * 1 - Entering to L1 LPM state enabled.
+ */
+#define USB_STS_L1ENS_MASK BIT(16)
+#define USB_STS_L1ENS(p) ((p) & USB_STS_L1ENS_MASK)
+/*
+ * Internal VBUS connection status (used both in HS/FS and SS mode).
+ * 0 - internal VBUS is not detected.
+ * 1 - internal VBUS is detected.
+ */
+#define USB_STS_VBUSS_MASK BIT(17)
+#define USB_STS_VBUSS(p) ((p) & USB_STS_VBUSS_MASK)
+/*
+ * HS/FS LPM state (used in FS/HS mode).
+ * 0 - L0 State
+ * 1 - L1 State
+ * 2 - L2 State
+ * 3 - L3 State
+ */
+#define USB_STS_LPMST_MASK GENMASK(19, 18)
+#define DEV_L0_STATE(p) (((p) & USB_STS_LPMST_MASK) == (0x0 << 18))
+#define DEV_L1_STATE(p) (((p) & USB_STS_LPMST_MASK) == (0x1 << 18))
+#define DEV_L2_STATE(p) (((p) & USB_STS_LPMST_MASK) == (0x2 << 18))
+#define DEV_L3_STATE(p) (((p) & USB_STS_LPMST_MASK) == (0x3 << 18))
+/*
+ * Disable HS status (used in FS/HS mode).
+ * 0 - the disconnect bit for HS/FS mode is set .
+ * 1 - the disconnect bit for HS/FS mode is not set.
+ */
+#define USB_STS_USB2CONS_MASK BIT(20)
+#define USB_STS_USB2CONS(p) ((p) & USB_STS_USB2CONS_MASK)
+/*
+ * HS/FS mode connection status (used in FS/HS mode).
+ * 0 - High Speed operations in USB2.0 (FS/HS) mode not disabled.
+ * 1 - High Speed operations in USB2.0 (FS/HS).
+ */
+#define USB_STS_DISABLE_HS_MASK BIT(21)
+#define USB_STS_DISABLE_HS(p) ((p) & USB_STS_DISABLE_HS_MASK)
+/*
+ * U1 state enable status (used in SS mode).
+ * 0 - Entering to U1 state disabled.
+ * 1 - Entering to U1 state enabled.
+ */
+#define USB_STS_U1ENS_MASK BIT(24)
+#define USB_STS_U1ENS(p) ((p) & USB_STS_U1ENS_MASK)
+/*
+ * U2 state enable status (used in SS mode).
+ * 0 - Entering to U2 state disabled.
+ * 1 - Entering to U2 state enabled.
+ */
+#define USB_STS_U2ENS_MASK BIT(25)
+#define USB_STS_U2ENS(p) ((p) & USB_STS_U2ENS_MASK)
+/*
+ * SuperSpeed Link LTSSM state. This field reflects USBSS-DEV current
+ * SuperSpeed link state
+ */
+#define USB_STS_LST_MASK GENMASK(29, 26)
+#define DEV_LST_U0 (((p) & USB_STS_LST_MASK) == (0x0 << 26))
+#define DEV_LST_U1 (((p) & USB_STS_LST_MASK) == (0x1 << 26))
+#define DEV_LST_U2 (((p) & USB_STS_LST_MASK) == (0x2 << 26))
+#define DEV_LST_U3 (((p) & USB_STS_LST_MASK) == (0x3 << 26))
+#define DEV_LST_DISABLED (((p) & USB_STS_LST_MASK) == (0x4 << 26))
+#define DEV_LST_RXDETECT (((p) & USB_STS_LST_MASK) == (0x5 << 26))
+#define DEV_LST_INACTIVE (((p) & USB_STS_LST_MASK) == (0x6 << 26))
+#define DEV_LST_POLLING (((p) & USB_STS_LST_MASK) == (0x7 << 26))
+#define DEV_LST_RECOVERY (((p) & USB_STS_LST_MASK) == (0x8 << 26))
+#define DEV_LST_HOT_RESET (((p) & USB_STS_LST_MASK) == (0x9 << 26))
+#define DEV_LST_COMP_MODE (((p) & USB_STS_LST_MASK) == (0xa << 26))
+#define DEV_LST_LB_STATE (((p) & USB_STS_LST_MASK) == (0xb << 26))
+/*
+ * DMA clock turn-off status.
+ * 0 - DMA clock is always on (default after hardware reset).
+ * 1 - DMA clock turn-off in U1, U2 and U3 (SS mode) is enabled.
+ */
+#define USB_STS_DMAOFF_MASK BIT(30)
+#define USB_STS_DMAOFF(p) ((p) & USB_STS_DMAOFF_MASK)
+/*
+ * SFR Endian statuss.
+ * 0 - Little Endian order (default after hardware reset).
+ * 1 - Big Endian order.
+ */
+#define USB_STS_ENDIAN2_MASK BIT(31)
+#define USB_STS_ENDIAN2(p) ((p) & USB_STS_ENDIAN2_MASK)
+
+/* USB_CMD - bitmasks */
+/* Set Function Address */
+#define USB_CMD_SET_ADDR BIT(0)
+/*
+ * Function Address This field is saved to the device only when the field
+ * SET_ADDR is set '1 ' during write to USB_CMD register.
+ * Software is responsible for entering the address of the device during
+ * SET_ADDRESS request service. This field should be set immediately after
+ * the SETUP packet is decoded, and prior to confirmation of the status phase
+ */
+#define USB_CMD_FADDR_MASK GENMASK(7, 1)
+#define USB_CMD_FADDR(p) (((p) << 1) & USB_CMD_FADDR_MASK)
+/* Send Function Wake Device Notification TP (used only in SS mode). */
+#define USB_CMD_SDNFW BIT(8)
+/* Set Test Mode (used only in HS/FS mode). */
+#define USB_CMD_STMODE BIT(9)
+/* Test mode selector (used only in HS/FS mode) */
+#define USB_STS_TMODE_SEL_MASK GENMASK(11, 10)
+#define USB_STS_TMODE_SEL(p) (((p) << 10) & USB_STS_TMODE_SEL_MASK)
+/*
+ * Send Latency Tolerance Message Device Notification TP (used only
+ * in SS mode).
+ */
+#define USB_CMD_SDNLTM BIT(12)
+/* Send Custom Transaction Packet (used only in SS mode) */
+#define USB_CMD_SPKT BIT(13)
+/*Device Notification 'Function Wake' - Interface value (only in SS mode. */
+#define USB_CMD_DNFW_INT_MASK GENMASK(23, 16)
+#define USB_STS_DNFW_INT(p) (((p) << 16) & USB_CMD_DNFW_INT_MASK)
+/*
+ * Device Notification 'Latency Tolerance Message' -373 BELT value [7:0]
+ * (used only in SS mode).
+ */
+#define USB_CMD_DNLTM_BELT_MASK GENMASK(27, 16)
+#define USB_STS_DNLTM_BELT(p) (((p) << 16) & USB_CMD_DNLTM_BELT_MASK)
+
+/* USB_ITPN - bitmasks */
+/*
+ * ITP(SS) / SOF (HS/FS) number
+ * In SS mode this field represent number of last ITP received from host.
+ * In HS/FS mode this field represent number of last SOF received from host.
+ */
+#define USB_ITPN_MASK GENMASK(13, 0)
+#define USB_ITPN(p) ((p) & USB_ITPN_MASK)
+
+/* USB_LPM - bitmasks */
+/* Host Initiated Resume Duration. */
+#define USB_LPM_HIRD_MASK GENMASK(3, 0)
+#define USB_LPM_HIRD(p) ((p) & USB_LPM_HIRD_MASK)
+/* Remote Wakeup Enable (bRemoteWake). */
+#define USB_LPM_BRW BIT(4)
+
+/* USB_IEN - bitmasks */
+/* SS connection interrupt enable */
+#define USB_IEN_CONIEN BIT(0)
+/* SS disconnection interrupt enable. */
+#define USB_IEN_DISIEN BIT(1)
+/* USB SS warm reset interrupt enable. */
+#define USB_IEN_UWRESIEN BIT(2)
+/* USB SS hot reset interrupt enable */
+#define USB_IEN_UHRESIEN BIT(3)
+/* SS link U3 state enter interrupt enable (suspend).*/
+#define USB_IEN_U3ENTIEN BIT(4)
+/* SS link U3 state exit interrupt enable (wakeup). */
+#define USB_IEN_U3EXTIEN BIT(5)
+/* SS link U2 state enter interrupt enable.*/
+#define USB_IEN_U2ENTIEN BIT(6)
+/* SS link U2 state exit interrupt enable.*/
+#define USB_IEN_U2EXTIEN BIT(7)
+/* SS link U1 state enter interrupt enable.*/
+#define USB_IEN_U1ENTIEN BIT(8)
+/* SS link U1 state exit interrupt enable.*/
+#define USB_IEN_U1EXTIEN BIT(9)
+/* ITP/SOF packet detected interrupt enable.*/
+#define USB_IEN_ITPIEN BIT(10)
+/* Wakeup interrupt enable.*/
+#define USB_IEN_WAKEIEN BIT(11)
+/* Send Custom Packet interrupt enable.*/
+#define USB_IEN_SPKTIEN BIT(12)
+/* HS/FS mode connection interrupt enable.*/
+#define USB_IEN_CON2IEN BIT(16)
+/* HS/FS mode disconnection interrupt enable.*/
+#define USB_IEN_DIS2IEN BIT(17)
+/* USB reset (HS/FS mode) interrupt enable.*/
+#define USB_IEN_U2RESIEN BIT(18)
+/* LPM L2 state enter interrupt enable.*/
+#define USB_IEN_L2ENTIEN BIT(20)
+/* LPM L2 state exit interrupt enable.*/
+#define USB_IEN_L2EXTIEN BIT(21)
+/* LPM L1 state enter interrupt enable.*/
+#define USB_IEN_L1ENTIEN BIT(24)
+/* LPM L1 state exit interrupt enable.*/
+#define USB_IEN_L1EXTIEN BIT(25)
+/* Configuration reset interrupt enable.*/
+#define USB_IEN_CFGRESIEN BIT(26)
+/* Start of the USB SS warm reset interrupt enable.*/
+#define USB_IEN_UWRESSIEN BIT(28)
+/* End of the USB SS warm reset interrupt enable.*/
+#define USB_IEN_UWRESEIEN BIT(29)
+
+#define USB_IEN_INIT (USB_IEN_U2RESIEN | USB_ISTS_DIS2I | USB_IEN_CON2IEN \
+ | USB_IEN_UHRESIEN | USB_IEN_UWRESIEN | USB_IEN_DISIEN \
+ | USB_IEN_CONIEN | USB_IEN_U3EXTIEN | USB_IEN_L2ENTIEN \
+ | USB_IEN_L2EXTIEN)
+
+/* USB_ISTS - bitmasks */
+/* SS Connection detected. */
+#define USB_ISTS_CONI BIT(0)
+/* SS Disconnection detected. */
+#define USB_ISTS_DISI BIT(1)
+/* UUSB warm reset detectede. */
+#define USB_ISTS_UWRESI BIT(2)
+/* USB hot reset detected. */
+#define USB_ISTS_UHRESI BIT(3)
+/* U3 link state enter detected (suspend).*/
+#define USB_ISTS_U3ENTI BIT(4)
+/* U3 link state exit detected (wakeup). */
+#define USB_ISTS_U3EXTI BIT(5)
+/* U2 link state enter detected.*/
+#define USB_ISTS_U2ENTI BIT(6)
+/* U2 link state exit detected.*/
+#define USB_ISTS_U2EXTI BIT(7)
+/* U1 link state enter detected.*/
+#define USB_ISTS_U1ENTI BIT(8)
+/* U1 link state exit detected.*/
+#define USB_ISTS_U1EXTI BIT(9)
+/* ITP/SOF packet detected.*/
+#define USB_ISTS_ITPI BIT(10)
+/* Wakeup detected.*/
+#define USB_ISTS_WAKEI BIT(11)
+/* Send Custom Packet detected.*/
+#define USB_ISTS_SPKTI BIT(12)
+/* HS/FS mode connection detected.*/
+#define USB_ISTS_CON2I BIT(16)
+/* HS/FS mode disconnection detected.*/
+#define USB_ISTS_DIS2I BIT(17)
+/* USB reset (HS/FS mode) detected.*/
+#define USB_ISTS_U2RESI BIT(18)
+/* LPM L2 state enter detected.*/
+#define USB_ISTS_L2ENTI BIT(20)
+/* LPM L2 state exit detected.*/
+#define USB_ISTS_L2EXTI BIT(21)
+/* LPM L1 state enter detected.*/
+#define USB_ISTS_L1ENTI BIT(24)
+/* LPM L1 state exit detected.*/
+#define USB_ISTS_L1EXTI BIT(25)
+/* USB configuration reset detected.*/
+#define USB_ISTS_CFGRESI BIT(26)
+/* Start of the USB warm reset detected.*/
+#define USB_ISTS_UWRESSI BIT(28)
+/* End of the USB warm reset detected.*/
+#define USB_ISTS_UWRESEI BIT(29)
+
+/* USB_SEL - bitmasks */
+#define EP_SEL_EPNO_MASK GENMASK(3, 0)
+/* Endpoint number. */
+#define EP_SEL_EPNO(p) ((p) & EP_SEL_EPNO_MASK)
+/* Endpoint direction bit - 0 - OUT, 1 - IN. */
+#define EP_SEL_DIR BIT(7)
+
+#define select_ep_in(nr) (EP_SEL_EPNO(p) | EP_SEL_DIR)
+#define select_ep_out (EP_SEL_EPNO(p))
+
+/* EP_TRADDR - bitmasks */
+/* Transfer Ring address. */
+#define EP_TRADDR_TRADDR(p) ((p))
+
+/* EP_CFG - bitmasks */
+/* Endpoint enable */
+#define EP_CFG_ENABLE BIT(0)
+/*
+ * Endpoint type.
+ * 1 - isochronous
+ * 2 - bulk
+ * 3 - interrupt
+ */
+#define EP_CFG_EPTYPE_MASK GENMASK(2, 1)
+#define EP_CFG_EPTYPE(p) (((p) << 1) & EP_CFG_EPTYPE_MASK)
+/* Stream support enable (only in SS mode). */
+#define EP_CFG_STREAM_EN BIT(3)
+/* TDL check (only in SS mode for BULK EP). */
+#define EP_CFG_TDL_CHK BIT(4)
+/* SID check (only in SS mode for BULK OUT EP). */
+#define EP_CFG_SID_CHK BIT(5)
+/* DMA transfer endianness. */
+#define EP_CFG_EPENDIAN BIT(7)
+/* Max burst size (used only in SS mode). */
+#define EP_CFG_MAXBURST_MASK GENMASK(11, 8)
+#define EP_CFG_MAXBURST(p) (((p) << 8) & EP_CFG_MAXBURST_MASK)
+/* ISO max burst. */
+#define EP_CFG_MULT_MASK GENMASK(15, 14)
+#define EP_CFG_MULT(p) (((p) << 14) & EP_CFG_MULT)
+/* ISO max burst. */
+#define EP_CFG_MAXPKTSIZE_MASK GENMASK(26, 16)
+#define EP_CFG_MAXPKTSIZE(p) (((p) << 16) & EP_CFG_MAXPKTSIZE_MASK)
+/* Max number of buffered packets. */
+#define EP_CFG_BUFFERING_MASK GENMASK(31, 27)
+#define EP_CFG_BUFFERING(p) (((p) << 27) & EP_CFG_BUFFERING_MASK)
+
+/* EP_CMD - bitmasks */
+/* Endpoint reset. */
+#define EP_CMD_EPRST BIT(0)
+/* Endpoint STALL set. */
+#define EP_CMD_SSTALL BIT(1)
+/* Endpoint STALL clear. */
+#define EP_CMD_CSTALL BIT(2)
+/* Send ERDY TP. */
+#define EP_CMD_ERDY BIT(3)
+/* Request complete. */
+#define EP_CMD_REQ_CMPL BIT(5)
+/* Transfer descriptor ready. */
+#define EP_CMD_DRDY BIT(6)
+/* Data flush. */
+#define EP_CMD_DFLUSH BIT(7)
+/*
+ * Transfer Descriptor Length write (used only for Bulk Stream capable
+ * endpoints in SS mode).
+ */
+#define EP_CMD_STDL BIT(8)
+/* Transfer Descriptor Length (used only in SS mode for bulk endpoints). */
+#define EP_CMD_TDL_MASK GENMASK(15, 9)
+#define EP_CMD_TDL(p) (((p) << 9) & EP_CMD_TDL_MASK)
+/* ERDY Stream ID value (used in SS mode). */
+#define EP_CMD_ERDY_SID_MASK GENMASK(31, 16)
+#define EP_CMD_ERDY_SID(p) (((p) << 16) & EP_CMD_SID_MASK)
+
+/* EP_STS - bitmasks */
+/* Setup transfer complete. */
+#define EP_STS_SETUP BIT(0)
+/* Endpoint STALL status. */
+#define EP_STS_STALL(p) ((p) & BIT(1))
+/* Interrupt On Complete. */
+#define EP_STS_IOC BIT(2)
+/* Interrupt on Short Packet. */
+#define EP_STS_ISP BIT(3)
+/* Transfer descriptor missing. */
+#define EP_STS_DESCMIS BIT(4)
+/* Stream Rejected (used only in SS mode) */
+#define EP_STS_STREAMR BIT(5)
+/* EXIT from MOVE DATA State (used only for stream transfers in SS mode). */
+#define EP_STS_MD_EXIT BIT(6)
+/* TRB error. */
+#define EP_STS_TRBERR BIT(7)
+/* Not ready (used only in SS mode). */
+#define EP_STS_NRDY BIT(8)
+/* DMA busy. */
+#define EP_STS_DBUSY(p) ((p) & BIT(9))
+/* Endpoint Buffer Empty */
+#define EP_STS_BUFFEMPTY(p) ((p) & BIT(10))
+/* Current Cycle Status */
+#define EP_STS_CCS(p) ((p) & BIT(11))
+/* Prime (used only in SS mode. */
+#define EP_STS_PRIME BIT(12)
+/* Stream error (used only in SS mode). */
+#define EP_STS_SIDERR BIT(13)
+/* OUT size mismatch. */
+#define EP_STS_OUTSMM BIT(14)
+/* ISO transmission error. */
+#define EP_STS_ISOERR BIT(15)
+/* Host Packet Pending (only for SS mode). */
+#define EP_STS_HOSTPP(p) ((p) & BIT(16))
+/* Stream Protocol State Machine State (only for Bulk stream endpoints). */
+#define EP_STS_SPSMST_MASK GENMASK(18, 17)
+#define EP_STS_SPSMST_DISABLED(p) (((p) & EP_STS_SPSMST_MASK) >> 17)
+#define EP_STS_SPSMST_IDLE(p) (((p) & EP_STS_SPSMST_MASK) >> 17)
+#define EP_STS_SPSMST_START_STREAM(p) (((p) & EP_STS_SPSMST_MASK) >> 17)
+#define EP_STS_SPSMST_MOVE_DATA(p) (((p) & EP_STS_SPSMST_MASK) >> 17)
+/* Interrupt On Transfer complete. */
+#define EP_STS_IOT BIT(19)
+/* OUT queue endpoint number. */
+#define EP_STS_OUTQ_NO_MASK GENMASK(27, 24)
+#define EP_STS_OUTQ_NO(p) (((p) & EP_STS_OUTQ_NO_MASK) >> 24)
+/* OUT queue valid flag. */
+#define EP_STS_OUTQ_VAL_MASK BIT(28)
+#define EP_STS_OUTQ_VAL(p) ((p) & EP_STS_OUTQ_VAL_MASK)
+/* SETUP WAIT. */
+#define EP_STS_STPWAIT BIT(31)
+
+/* EP_STS_SID - bitmasks */
+/* Stream ID (used only in SS mode). */
+#define EP_STS_SID_MASK GENMASK(15, 0)
+#define EP_STS_SID(p) ((p) & EP_STS_SID_MASK)
+
+/* EP_STS_EN - bitmasks */
+/* SETUP interrupt enable. */
+#define EP_STS_EN_SETUPEN BIT(0)
+/* OUT transfer missing descriptor enable. */
+#define EP_STS_EN_DESCMISEN BIT(4)
+/* Stream Rejected enable. */
+#define EP_STS_EN_STREAMREN BIT(5)
+/* Move Data Exit enable.*/
+#define EP_STS_EN_MD_EXITEN BIT(6)
+/* TRB enable. */
+#define EP_STS_EN_TRBERREN BIT(7)
+/* NRDY enable. */
+#define EP_STS_EN_NRDYEN BIT(8)
+/* Prime enable. */
+#define EP_STS_EN_PRIMEEEN BIT(12)
+/* Stream error enable. */
+#define EP_STS_EN_SIDERREN BIT(13)
+/* OUT size mismatch enable. */
+#define EP_STS_EN_OUTSMMEN BIT(14)
+/* ISO transmission error enable. */
+#define EP_STS_EN_ISOERREN BIT(15)
+/* Interrupt on Transmission complete enable. */
+#define EP_STS_EN_IOTEN BIT(19)
+/* Setup Wait interrupt enable. */
+#define EP_STS_EN_STPWAITEN BIT(31)
+
+/* DRBL- bitmasks */
+#define DB_VALUE_BY_INDEX(index) (1 << (index))
+#define DB_VALUE_EP0_OUT BIT(0)
+#define DB_VALUE_EP0_IN BIT(16)
+
+/* EP_IEN - bitmasks */
+#define EP_IEN(index) (1 << (index))
+#define EP_IEN_EP_OUT0 BIT(0)
+#define EP_IEN_EP_IN0 BIT(16)
+
+/* EP_ISTS - bitmasks */
+#define EP_ISTS(index) (1 << (index))
+#define EP_ISTS_EP_OUT0 BIT(0)
+#define EP_ISTS_EP_IN0 BIT(16)
+
+/* EP_PWR- bitmasks */
+/*Power Shut Off capability enable*/
+#define PUSB_PWR_PSO_EN BIT(0)
+/*Power Shut Off capability disable*/
+#define PUSB_PWR_PSO_DS BIT(1)
+/*
+ * Enables turning-off Reference Clock.
+ * This bit is optional and implemented only when support for OTG is
+ * implemented (indicated by OTG_READY bit set to '1').
+ */
+#define PUSB_PWR_STB_CLK_SWITCH_EN BIT(8)
+/*
+ * Status bit indicating that operation required by STB_CLK_SWITCH_EN write
+ * is completed
+ */
+#define PUSB_PWR_STB_CLK_SWITCH_DONE BIT(9)
+/* This bit informs if Fast Registers Access is enabled. */
+#define PUSB_PWR_FST_REG_ACCESS_STAT BIT(30)
+/* Fast Registers Access Enable. */
+#define PUSB_PWR_FST_REG_ACCESS BIT(31)
+
+/* USB_CAP1- bitmasks */
+/*
+ * SFR Interface type
+ * These field reflects type of SFR interface implemented:
+ * 0x0 - OCP
+ * 0x1 - AHB,
+ * 0x2 - PLB
+ * 0x3 - AXI
+ * 0x4-0xF - reserved
+ */
+#define USB_CAP1_SFR_TYPE_MASK GENMASK(3, 0)
+#define DEV_SFR_TYPE_OCP(p) (((p) & USB_CAP1_SFR_TYPE_MASK) == 0x0)
+#define DEV_SFR_TYPE_AHB(p) (((p) & USB_CAP1_SFR_TYPE_MASK) == 0x1)
+#define DEV_SFR_TYPE_PLB(p) (((p) & USB_CAP1_SFR_TYPE_MASK) == 0x2)
+#define DEV_SFR_TYPE_AXI(p) (((p) & USB_CAP1_SFR_TYPE_MASK) == 0x3)
+/*
+ * SFR Interface width
+ * These field reflects width of SFR interface implemented:
+ * 0x0 - 8 bit interface,
+ * 0x1 - 16 bit interface,
+ * 0x2 - 32 bit interface
+ * 0x3 - 64 bit interface
+ * 0x4-0xF - reserved
+ */
+#define USB_CAP1_SFR_WIDTH_MASK GENMASK(7, 4)
+#define DEV_SFR_WIDTH_8(p) (((p) & USB_CAP1_SFR_WIDTH_MASK) == (0x0 << 4))
+#define DEV_SFR_WIDTH_16(p) (((p) & USB_CAP1_SFR_WIDTH_MASK) == (0x1 << 4))
+#define DEV_SFR_WIDTH_32(p) (((p) & USB_CAP1_SFR_WIDTH_MASK) == (0x2 << 4))
+#define DEV_SFR_WIDTH_64(p) (((p) & USB_CAP1_SFR_WIDTH_MASK) == (0x3 << 4))
+/*
+ * DMA Interface type
+ * These field reflects type of DMA interface implemented:
+ * 0x0 - OCP
+ * 0x1 - AHB,
+ * 0x2 - PLB
+ * 0x3 - AXI
+ * 0x4-0xF - reserved
+ */
+#define USB_CAP1_DMA_TYPE_MASK GENMASK(11, 8)
+#define DEV_DMA_TYPE_OCP(p) (((p) & USB_CAP1_DMA_TYPE_MASK) == (0x0 << 8))
+#define DEV_DMA_TYPE_AHB(p) (((p) & USB_CAP1_DMA_TYPE_MASK) == (0x1 << 8))
+#define DEV_DMA_TYPE_PLB(p) (((p) & USB_CAP1_DMA_TYPE_MASK) == (0x2 << 8))
+#define DEV_DMA_TYPE_AXI(p) (((p) & USB_CAP1_DMA_TYPE_MASK) == (0x3 << 8))
+/*
+ * DMA Interface width
+ * These field reflects width of DMA interface implemented:
+ * 0x0 - reserved,
+ * 0x1 - reserved,
+ * 0x2 - 32 bit interface
+ * 0x3 - 64 bit interface
+ * 0x4-0xF - reserved
+ */
+#define USB_CAP1_DMA_WIDTH_MASK GENMASK(15, 12)
+#define DEV_DMA_WIDTH_32(p) (((p) & USB_CAP1_DMA_WIDTH_MASK) == (0x2 << 12))
+#define DEV_DMA_WIDTH_64(p) (((p) & USB_CAP1_DMA_WIDTH_MASK) == (0x3 << 12))
+/*
+ * USB3 PHY Interface type
+ * These field reflects type of USB3 PHY interface implemented:
+ * 0x0 - USB PIPE,
+ * 0x1 - RMMI,
+ * 0x2-0xF - reserved
+ */
+#define USB_CAP1_U3PHY_TYPE_MASK GENMASK(19, 16)
+#define DEV_U3PHY_PIPE(p) (((p) & USB_CAP1_U3PHY_TYPE_MASK) == (0x0 << 16))
+#define DEV_U3PHY_RMMI(p) (((p) & USB_CAP1_U3PHY_TYPE_MASK) == (0x1 << 16))
+/*
+ * USB3 PHY Interface width
+ * These field reflects width of USB3 PHY interface implemented:
+ * 0x0 - 8 bit PIPE interface,
+ * 0x1 - 16 bit PIPE interface,
+ * 0x2 - 32 bit PIPE interface,
+ * 0x3 - 64 bit PIPE interface
+ * 0x4-0xF - reserved
+ * Note: When SSIC interface is implemented this field shows the width of
+ * internal PIPE interface. The RMMI interface is always 20bit wide.
+ */
+#define USB_CAP1_U3PHY_WIDTH_MASK GENMASK(23, 20)
+#define DEV_U3PHY_WIDTH_8(p) \
+ (((p) & USB_CAP1_U3PHY_WIDTH_MASK) == (0x0 << 20))
+#define DEV_U3PHY_WIDTH_16(p) \
+ (((p) & USB_CAP1_U3PHY_WIDTH_MASK) == (0x1 << 16))
+#define DEV_U3PHY_WIDTH_32(p) \
+ (((p) & USB_CAP1_U3PHY_WIDTH_MASK) == (0x2 << 20))
+#define DEV_U3PHY_WIDTH_64(p) \
+ (((p) & USB_CAP1_U3PHY_WIDTH_MASK) == (0x3 << 16))
+
+/*
+ * USB2 PHY Interface enable
+ * These field informs if USB2 PHY interface is implemented:
+ * 0x0 - interface NOT implemented,
+ * 0x1 - interface implemented
+ */
+#define USB_CAP1_U2PHY_EN(p) ((p) & BIT(24))
+/*
+ * USB2 PHY Interface type
+ * These field reflects type of USB2 PHY interface implemented:
+ * 0x0 - UTMI,
+ * 0x1 - ULPI
+ */
+#define DEV_U2PHY_ULPI(p) ((p) & BIT(25))
+/*
+ * USB2 PHY Interface width
+ * These field reflects width of USB2 PHY interface implemented:
+ * 0x0 - 8 bit interface,
+ * 0x1 - 16 bit interface,
+ * Note: The ULPI interface is always 8bit wide.
+ */
+#define DEV_U2PHY_WIDTH_16(p) ((p) & BIT(26))
+/*
+ * OTG Ready
+ * 0x0 - pure device mode
+ * 0x1 - some features and ports for CDNS USB OTG controller are implemented.
+ */
+#define USB_CAP1_OTG_READY(p) ((p) & BIT(27))
+
+/* USB_CAP2- bitmasks */
+/*
+ * The actual size of the connected On-chip RAM memory in kB:
+ * - 0 means 256 kB (max supported mem size)
+ * - value other than 0 reflects the mem size in kB
+ */
+#define USB_CAP2_ACTUAL_MEM_SIZE(p) ((p) & GENMASK(7, 0))
+/*
+ * Max supported mem size
+ * These field reflects width of on-chip RAM address bus width,
+ * which determines max supported mem size:
+ * 0x0-0x7 - reserved,
+ * 0x8 - support for 4kB mem,
+ * 0x9 - support for 8kB mem,
+ * 0xA - support for 16kB mem,
+ * 0xB - support for 32kB mem,
+ * 0xC - support for 64kB mem,
+ * 0xD - support for 128kB mem,
+ * 0xE - support for 256kB mem,
+ * 0xF - reserved
+ */
+#define USB_CAP2_MAX_MEM_SIZE(p) ((p) & GENMASK(11, 8))
+
+/* USB_CAP3- bitmasks */
+#define EP_IS_IMPLEMENTED(reg, index) ((reg) & (1 << (index)))
+
+/* USB_CAP4- bitmasks */
+#define EP_SUPPORT_ISO(reg, index) ((reg) & (1 << (index)))
+
+/* USB_CAP5- bitmasks */
+#define EP_SUPPORT_STREAM(reg, index) ((reg) & (1 << (index)))
+
+/* USB_CAP6- bitmasks */
+/* The USBSS-DEV Controller Internal build number. */
+#define GET_DEV_VERSION__INTERNAL_NUMBER(p) ((p) & GENMASK(7, 0))
+/* The USBSS-DEV Controller version number. */
+#define GET_DEV_VERSION(p) ((p) & GENMASK(31, 8))
+
+/* DBG_LINK1- bitmasks */
+/*
+ * LFPS_MIN_DET_U1_EXIT value This parameter configures the minimum
+ * time required for decoding the received LFPS as an LFPS.U1_Exit.
+ */
+#define DBG_LINK1_LFPS_MIN_DET_U1_EXIT(p) ((p) & GENMASK(7, 0))
+/*
+ * LFPS_MIN_GEN_U1_EXIT value This parameter configures the minimum time for
+ * phytxelecidle deassertion when LFPS.U1_Exit
+ */
+#define DBG_LINK1_LFPS_MIN_GEN_U1_EXIT(p) (((p) << 8) & GENMASK(15, 8))
+/*
+ * RXDET_BREAK_DIS value This parameter configures terminating the Far-end
+ * Receiver termination detection sequence:
+ * 0: it is possible that USBSS_DEV will terminate Farend receiver
+ * termination detection sequence
+ * 1: USBSS_DEV will not terminate Far-end receiver termination
+ * detection sequence
+ */
+#define DBG_LINK1_RXDET_BREAK_DIS BIT(16)
+/* LFPS_GEN_PING value This parameter configures the LFPS.Ping generation */
+#define DBG_LINK1_LFPS_GEN_PING(p) (((p) << 17) & GENMASK(21, 17))
+/*
+ * Set the LFPS_MIN_DET_U1_EXIT value Writing '1' to this bit writes the
+ * LFPS_MIN_DET_U1_EXIT field value to the device. This bit is automatically
+ * cleared. Writing '0' has no effect
+ */
+#define DBG_LINK1_LFPS_MIN_DET_U1_EXIT_SET BIT(24)
+/*
+ * Set the LFPS_MIN_GEN_U1_EXIT value. Writing '1' to this bit writes the
+ * LFPS_MIN_GEN_U1_EXIT field value to the device. This bit is automatically
+ * cleared. Writing '0' has no effect
+ */
+#define DBG_LINK1_LFPS_MIN_GEN_U1_EXIT_SET BIT(25)
+/*
+ * Set the RXDET_BREAK_DIS value Writing '1' to this bit writes
+ * the RXDET_BREAK_DIS field value to the device. This bit is automatically
+ * cleared. Writing '0' has no effect
+ */
+#define DBG_LINK1_RXDET_BREAK_DIS_SET BIT(26)
+/*
+ * Set the LFPS_GEN_PING_SET value Writing '1' to this bit writes
+ * the LFPS_GEN_PING field value to the device. This bit is automatically
+ * cleared. Writing '0' has no effect."
+ */
+#define DBG_LINK1_LFPS_GEN_PING_SET BIT(27)
+
+#define gadget_to_cdns3_device(g) (container_of(g, struct cdns3_device, gadget))
+
+#define ep_to_cdns3_ep(ep) (container_of(ep, struct cdns3_endpoint, endpoint))
+
+/*-------------------------------------------------------------------------*/
+/*
+ * USBSS-DEV DMA interface .
+ */
+#define TRBS_PER_SEGMENT 32
+
+struct cdns3_trb {
+ __le32 buffer;
+ __le32 length;
+ __le32 control;
+};
+
+#define TRB_SIZE (sizeof(struct cdns3_trb))
+#define TRB_RIGN_SIZE (TRB_SIZE * TRBS_PER_SEGMENT)
+
+/* TRB bit mask */
+#define TRB_TYPE_BITMASK GENMASK(15, 10)
+#define TRB_TYPE(p) ((p) << 10)
+#define TRB_FIELD_TO_TYPE(p) (((p) & TRB_TYPE_BITMASK) >> 10)
+
+/* TRB type IDs */
+/* bulk, interrupt, isoc , and control data stage */
+#define TRB_NORMAL 1
+/* TRB for linking ring segments */
+#define TRB_LINK 6
+
+/* Cycle bit - indicates TRB ownership by driver or hw*/
+#define TRB_CYCLE BIT(0)
+/*
+ * When set to '1', the device will toggle its interpretation of the Cycle bit
+ */
+#define TRB_TOGGLE BIT(1)
+
+/* Interrupt on short packet*/
+#define TRB_ISP BIT(2)
+/*Setting this bit enables FIFO DMA operation mode*/
+#define TRB_FIFO_MODE BIT(3)
+/* Set PCIe no snoop attribute */
+#define TRB_CHAIN BIT(4)
+/* Interrupt on completion */
+#define TRB_IOC BIT(5)
+
+/* stream ID bitmasks. */
+#define TRB_STREAM_ID(p) ((p) & GENMASK(31, 16))
+
+/* transfer_len bitmasks. */
+#define TRB_LEN(p) ((p) & GENMASK(16, 0))
+
+/* transfer_len bitmasks - bits 31:24 */
+#define TRB_BURST_LEN(p) ((p) & GENMASK(31, 24))
+
+/* Data buffer pointer bitmasks*/
+#define TRB_BUFFER(p) ((p) & GENMASK(31, 0))
+
+/*-------------------------------------------------------------------------*/
+/* Driver numeric constants */
+
+#define DEVICE_ADDRESS_MAX 127
+
+/* Endpoint init values */
+#define ENDPOINT_MAX_PACKET_LIMIT 1024
+#define ENDPOINT_MAX_STREAMS 15
+
+#define ENDPOINT0_MAX_PACKET_LIMIT 512
+
+/* All endpoints except EP0 */
+#define USB_SS_ENDPOINTS_MAX_COUNT 30
+
+#define ADDR_MODULO_8 8
+
+#define ENDPOINT_ZLP_BUF_SIZE 1024
+
+/*-------------------------------------------------------------------------*/
+/* 18KB is the total size, and 2KB is used for EP0 and configuration */
+#define CDNS3_ONCHIP_BUF_SIZE 16 /* KB */
+#define CDNS3_EP_BUF_SIZE 2 /* KB */
+#define CDNS3_UNALIGNED_BUF_SIZE 16384 /* Bytes */
+/*-------------------------------------------------------------------------*/
+/* Used structs */
+
+struct cdns3_device;
+
+struct cdns3_endpoint {
+ struct usb_ep endpoint;
+ struct list_head request_list;
+ struct list_head ep_match_pending_list;
+
+ struct cdns3_trb *trb_pool;
+ dma_addr_t trb_pool_dma;
+
+ struct cdns3_device *cdns3_dev;
+ char name[20];
+
+#define EP_ENABLED BIT(0)
+#define EP_STALL BIT(1)
+#define EP_WEDGE BIT(2)
+#define EP_TRANSFER_STARTED BIT(3)
+#define EP_UPDATE_EP_TRBADDR BIT(4)
+#define EP_PENDING_REQUEST BIT(5)
+#define EP_USED BIT(5)
+ u32 flags;
+
+ void *aligned_buff;
+ dma_addr_t aligned_dma_addr;
+ u8 dir;
+ u8 num;
+ u8 type;
+
+ int free_trbs;
+ u8 pcs;
+ u8 ccs;
+ int enqueue;
+ int dequeue;
+};
+
+struct cdns3_request {
+ struct usb_request request;
+ struct cdns3_endpoint *priv_ep;
+ struct cdns3_trb *trb;
+ int start_trb;
+ int end_trb;
+ int on_ring:1;
+};
+
+#define to_cdns3_request(r) (container_of(r, struct cdns3_request, request))
+
+struct cdns3_device {
+ struct device dev;
+ struct cdns3_usb_regs __iomem *regs;
+
+ struct usb_gadget gadget;
+ struct usb_gadget_driver *gadget_driver;
+
+ struct usb_ctrlrequest *setup;
+ dma_addr_t setup_dma;
+ dma_addr_t trb_ep0_dma;
+ struct cdns3_trb *trb_ep0;
+ void *zlp_buf;
+
+ struct cdns3_endpoint *eps[USB_SS_ENDPOINTS_MAX_COUNT];
+ int ep_nums;
+ /*
+ * field used for improving performance. It holds the last
+ * selected endpoint number
+ */
+ u32 selected_ep;
+ struct usb_request *ep0_request;
+ int ep0_data_dir;
+ int hw_configured_flag;
+ int wake_up_flag;
+ u16 isoch_delay;
+ /* generic spin-lock for drivers */
+ spinlock_t lock;
+
+ unsigned is_connected:1;
+ unsigned in_standby_mode:1;
+ unsigned status_completion_no_call:1;
+ unsigned u1_allowed:1;
+ unsigned u2_allowed:1;
+
+ u32 usb_ien;
+ u32 ep_ien;
+ int setup_pending;
+ struct device *sysdev;
+ /* The device mode is enabled */
+ int start_gadget;
+ struct list_head ep_match_list;
+ /* KB */
+ int onchip_mem_allocated_size;
+ /* Memory is allocated for OUT */
+ int out_mem_is_allocated:1;
+ struct work_struct pending_status_wq;
+ struct usb_request *pending_status_request;
+};
+
+#endif /* __LINUX_CDNS3_GADGET */
--
2.17.1
\
 
 \ /
  Last update: 2018-11-18 11:13    [W:0.470 / U:0.132 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site