lkml.org 
[lkml]   [2018]   [Nov]   [15]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH 1/2] clocksource: meson6_timer: use register names from the datasheet
From
Date
On 15/11/2018 07:23, Martin Blumenstingl wrote:
> Hi Daniel,
>
> thanks for your feedback!
>
> On Thu, Nov 15, 2018 at 2:35 AM Daniel Lezcano
> <daniel.lezcano@linaro.org> wrote:
>>
>> On 28/10/2018 13:55, Martin Blumenstingl wrote:
>>> This makes the driver use the names from S805 datasheet for the
>>> preprocessor #defines. This makes it easier to spot that the driver
>>> currently only supports Timer A (as clockevent with interrupt support)
>>> and Timer E (as clocksource without interrupts). Timer B, C and D (which
>>> are similar to Timer A) are currently not supported by the driver.
>>>
>>> While here, this also removes the internal "CED_ID" and "CSD_ID" defines
>>> which are used to identify the timer. These IDs are not described in the
>>> datasheet and thus make it harder to compare the code to what's written
>>> in the datasheet.
>>>
>>> Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
>>> ---
>>> drivers/clocksource/meson6_timer.c | 110 ++++++++++++++++++-----------
>>> 1 file changed, 68 insertions(+), 42 deletions(-)
>>>
>>> diff --git a/drivers/clocksource/meson6_timer.c b/drivers/clocksource/meson6_timer.c
>>> index 92f20991a937..c622135bee9d 100644
>>> --- a/drivers/clocksource/meson6_timer.c
>>> +++ b/drivers/clocksource/meson6_timer.c
>>> @@ -10,6 +10,8 @@
>>> * warranty of any kind, whether express or implied.
>>> */
>>>
>>> +#include <linux/bitfield.h>
>>> +#include <linux/bitops.h>
>>> #include <linux/clk.h>
>>> #include <linux/clockchips.h>
>>> #include <linux/interrupt.h>
>>> @@ -20,80 +22,102 @@
>>> #include <linux/of_address.h>
>>> #include <linux/of_irq.h>
>>>
>>> -#define CED_ID 0
>>> -#define CSD_ID 4
>>> -
>>> -#define TIMER_ISA_MUX 0
>>> -#define TIMER_ISA_VAL(t) (((t) + 1) << 2)
>>> -
>>> -#define TIMER_INPUT_BIT(t) (2 * (t))
>>> -#define TIMER_ENABLE_BIT(t) (16 + (t))
>>> -#define TIMER_PERIODIC_BIT(t) (12 + (t))
>>> +enum meson6_timera_input_clock {
>>> + MESON_TIMERA_CLOCK_1US = 0x0,
>>> + MESON_TIMERA_CLOCK_10US = 0x1,
>>> + MESON_TIMERA_CLOCK_100US = 0x2,
>>> + MESON_TIMERA_CLOCK_1MS = 0x3,
>>> +};
>>>
>>> -#define TIMER_CED_INPUT_MASK (3UL << TIMER_INPUT_BIT(CED_ID))
>>> -#define TIMER_CSD_INPUT_MASK (7UL << TIMER_INPUT_BIT(CSD_ID))
>>> +enum meson6_timere_input_clock {
>>> + MESON_TIMERE_CLOCK_SYSTEM_CLOCK = 0x0,
>>> + MESON_TIMERE_CLOCK_1US = 0x1,
>>> + MESON_TIMERE_CLOCK_10US = 0x2,
>>> + MESON_TIMERE_CLOCK_100US = 0x3,
>>> + MESON_TIMERE_CLOCK_1MS = 0x4,
>>> +};
>>
>> It is not required to specify the values. The standard defines the
>> default first value is zero, and each enum has the value which is +1 of
>> the previous one.
> the idea behind this is: these are values from the datasheet so I
> wanted to make them easy to find when comparing the datasheet with the
> driver.
> I will replace the enums with simple #defines if there are no
> objections (that also makes it consistent with the other register
> values in the driver).

No objection to change them to macros :)

-- Daniel


--
<http://www.linaro.org/> Linaro.org │ Open source software for ARM SoCs

Follow Linaro: <http://www.facebook.com/pages/Linaro> Facebook |
<http://twitter.com/#!/linaroorg> Twitter |
<http://www.linaro.org/linaro-blog/> Blog

\
 
 \ /
  Last update: 2018-11-15 13:16    [W:0.046 / U:0.312 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site