lkml.org 
[lkml]   [2018]   [Nov]   [15]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v6 3/5] dt-bindings: pinctrl: Add bindings for Actions Semi S700 SoC
On Tue, Nov 13, 2018 at 11:07:07AM +0100, Parthiban Nallathambi wrote:
> From: Saravanan Sekar <sravanhome@gmail.com>
>
> Add pinctrl and pio bindings for Actions Semi S700 SoC.
>
> Signed-off-by: Parthiban Nallathambi <pn@denx.de>
> Signed-off-by: Saravanan Sekar <sravanhome@gmail.com>
> Reviewed-by: Rob Herring <robh@kernel.org>
> ---
> .../bindings/pinctrl/actions,s700-pinctrl.txt | 170 ++++++++++++++++++
> 1 file changed, 170 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/pinctrl/actions,s700-pinctrl.txt
>
> diff --git a/Documentation/devicetree/bindings/pinctrl/actions,s700-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/actions,s700-pinctrl.txt
> new file mode 100644
> index 000000000000..c72c09c38537
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/pinctrl/actions,s700-pinctrl.txt
> @@ -0,0 +1,170 @@
> +Actions Semi S700 Pin Controller
> +
> +This binding describes the pin controller found in the S700 SoC.
> +
> +Required Properties:
> +
> +- compatible: Should be "actions,s700-pinctrl"
> +- reg: Should contain the register base address and size of
> + the pin controller.
> +- clocks: phandle of the clock feeding the pin controller
> +- gpio-controller: Marks the device node as a GPIO controller.
> +- gpio-ranges: Specifies the mapping between gpio controller and
> + pin-controller pins.
> +- #gpio-cells: Should be two. The first cell is the gpio pin number
> + and the second cell is used for optional parameters.
> +- interrupt-controller: Marks the device node as an interrupt controller.
> +- #interrupt-cells: Specifies the number of cells needed to encode an
> + interrupt. Shall be set to 2. The first cell
> + defines the interrupt number, the second encodes
> + the trigger flags described in
> + bindings/interrupt-controller/interrupts.txt
> +- interrupts: The interrupt outputs from the controller. There is one GPIO
> + interrupt per GPIO bank. The number of interrupts listed depends
> + on the number of GPIO banks on the SoC. The interrupts must be
> + ordered by bank, starting with bank 0.
> +
> +Please refer to pinctrl-bindings.txt in this directory for details of the
> +common pinctrl bindings used by client devices, including the meaning of the
> +phrase "pin configuration node".
> +
> +The pin configuration nodes act as a container for an arbitrary number of
> +subnodes. Each of these subnodes represents some desired configuration for a
> +pin, a group, or a list of pins or groups. This configuration can include the
> +mux function to select on those group(s), and various pin configuration
> +parameters, such as pull-up, drive strength, etc.
> +
> +PIN CONFIGURATION NODES:
> +
> +The name of each subnode is not important; all subnodes should be enumerated
> +and processed purely based on their content.
> +
> +Each subnode only affects those parameters that are explicitly listed. In
> +other words, a subnode that lists a mux function but no pin configuration
> +parameters implies no information about any pin configuration parameters.
> +Similarly, a pin subnode that describes a pullup parameter implies no
> +information about e.g. the mux function.
> +
> +Pinmux functions are available only for the pin groups while pinconf
> +parameters are available for both pin groups and individual pins.
> +
> +The following generic properties as defined in pinctrl-bindings.txt are valid
> +to specify in a pin configuration subnode:
> +
> +Required Properties:
> +
> +- pins: An array of strings, each string containing the name of a pin.
> + These pins are used for selecting the pull control and schmitt
> + trigger parameters. The following are the list of pins
> + available:
> +
> + eth_txd0, eth_txd1, eth_txd2, eth_txd3, eth_txen, eth_rxer,
> + eth_crs_dv, eth_rxd1, eth_rxd0, eth_rxd2, eth_rxd3, eth_ref_clk,
> + eth_mdc, eth_mdio, sirq0, sirq1, sirq2, i2s_d0, i2s_bclk0,
> + i2s_lrclk0, i2s_mclk0, i2s_d1, i2s_bclk1, i2s_lrclk1, i2s_mclk1,
> + pcm1_in, pcm1_clk, pcm1_sync, pcm1_out, ks_in0, ks_in1, ks_in2,
> + ks_in3, ks_out0, ks_out1, ks_out2, lvds_oep, lvds_oen, lvds_odp,
> + lvds_odn, lvds_ocp, lvds_ocn, lvds_obp, lvds_obn, lvds_oap,
> + lvds_oan, lvds_eep, lvds_een, lvds_edp, lvds_edn, lvds_ecp,
> + lvds_ecn, lvds_ebp, lvds_ebn, lvds_eap, lvds_ean, lcd0_d18,
> + lcd0_d2, dsi_dp3, dsi_dn3, dsi_dp1, dsi_dn1, dsi_cp, dsi_cn,
> + dsi_dp0, dsi_dn0, dsi_dp2, dsi_dn2, sd0_d0, sd0_d1, sd0_d2,
> + sd0_d3, sd1_d0, sd1_d1, sd1_d2, sd1_d3, sd0_cmd, sd0_clk,
> + sd1_cmd, sd1_clk, spi0_ss, spi0_miso, uart0_rx, uart0_tx,
> + uart2_rx, uart2_tx, uart2_rtsb, uart2_ctsb, uart3_rx, uart3_tx,
> + uart3_rtsb, uart3_ctsb, i2c0_sclk, i2c0_sdata, i2c1_sclk,
> + i2c1_sdata, i2c2_sdata, csi_dn0, csi_dp0, csi_dn1, csi_dp1,
> + csi_cn, csi_cp, csi_dn2, csi_dp2, csi_dn3, csi_dp3,
> + sensor0_pclk, sensor0_ckout, dnand_d0, dnand_d1, dnand_d2,
> + dnand_d3, dnand_d4, dnand_d5, dnand_d6, dnand_d7, dnand_wrb,
> + dnand_rdb, dnand_rdbn, dnand_dqs, dnand_dqsn, dnand_rb0,
> + dnand_ale, dnand_cle, dnand_ceb0, dnand_ceb1, dnand_ceb2,
> + dnand_ceb3, porb, clko_25m, bsel, pkg0, pkg1, pkg2, pkg3
> +
> +- groups: An array of strings, each string containing the name of a pin
> + group. These pin groups are used for selecting the pinmux
> + functions.
> + rgmii_txd23_mfp, rgmii_rxd2_mfp, rgmii_rxd3_mfp, lcd0_d18_mfp,
> + rgmii_txd01_mfp, rgmii_txd0_mfp, rgmii_txd1_mfp, rgmii_txen_mfp,
> + rgmii_rxen_mfp, rgmii_rxd1_mfp, rgmii_rxd0_mfp, rgmii_ref_clk_mfp,
> + i2s_d0_mfp, i2s_pcm1_mfp, i2s0_pcm0_mfp, i2s1_pcm0_mfp,
> + i2s_d1_mfp, ks_in2_mfp, ks_in1_mfp, ks_in0_mfp, ks_in3_mfp,
> + ks_out0_mfp, ks_out1_mfp, ks_out2_mfp, lvds_o_pn_mfp, dsi_dn0_mfp,
> + dsi_dp2_mfp, lcd0_d2_mfp, dsi_dp3_mfp, dsi_dn3_mfp, dsi_dp0_mfp,
> + lvds_ee_pn_mfp, uart2_rx_tx_mfp, spi0_i2c_pcm_mfp, dsi_dnp1_cp_d2_mfp,
> + dsi_dnp1_cp_d17_mfp, lvds_e_pn_mfp, dsi_dn2_mfp, uart2_rtsb_mfp,
> + uart2_ctsb_mfp, uart3_rtsb_mfp, uart3_ctsb_mfp, sd0_d0_mfp, sd0_d1_mfp,
> + sd0_d2_d3_mfp, sd1_d0_d3_mfp, sd0_cmd_mfp, sd0_clk_mfp, sd1_cmd_mfp,
> + uart0_rx_mfp, clko_25m_mfp, csi_cn_cp_mfp, sens0_ckout_mfp, uart0_tx_mfp,
> + i2c0_mfp, csi_dn_dp_mfp, sen0_pclk_mfp, pcm1_in_mfp, pcm1_clk_mfp,
> + pcm1_sync_mfp, pcm1_out_mfp, dnand_data_wr_mfp, dnand_acle_ce0_mfp,
> + nand_ceb2_mfp, nand_ceb3_mfp
> +
> + These pin groups are used for selecting the drive strength
> + parameters.
> +
> + sirq_drv, rgmii_txd23_drv, rgmii_rxd23_drv, rgmii_txd01_txen_drv,
> + rgmii_rxer_drv, rgmii_crs_drv, rgmii_rxd10_drv, rgmii_ref_clk_drv,
> + smi_mdc_mdio_drv, i2s_d0_drv, i2s_bclk0_drv, i2s3_drv, i2s13_drv,
> + pcm1_drv, ks_in_drv, ks_out_drv, lvds_all_drv, lcd_d18_d2_drv,
> + dsi_all_drv, sd0_d0_d3_drv, sd0_cmd_drv, sd0_clk_drv, spi0_all_drv,
> + uart0_rx_drv, uart0_tx_drv, uart2_all_drv, i2c0_all_drv, i2c12_all_drv,
> + sens0_pclk_drv, sens0_ckout_drv, uart3_all_drv
> +
> +- function: An array of strings, each string containing the name of the
> + pinmux functions. These functions can only be selected by
> + the corresponding pin groups. The following are the list of
> + pinmux functions available:
> +
> + nor, eth_rgmii, eth_sgmii, spi0, spi1, spi2, spi3, seNs0, sens1,
> + uart0, uart1, uart2, uart3, uart4, uart5, uart6, i2s0, i2s1,
> + pcm1, pcm0, ks, jtag, pwm0, pwm1, pwm2, pwm3, pwm4, pwm5, p0,
> + sd0, sd1, sd2, i2c0, i2c1, i2c2, i2c3, dsi, lvds, usb30,
> + clko_25m, mipi_csi, nand, spdif, sirq0, sirq1, sirq2, bt, lcd0
> +
> +Optional Properties:
> +
> +- bias-pull-down: No arguments. The specified pins should be configured as
> + pull down.
> +- bias-pull-up: No arguments. The specified pins should be configured as
> + pull up.
> +- input-schmitt-enable: No arguments: Enable schmitt trigger for the specified
> + pins
> +- input-schmitt-disable: No arguments: Disable schmitt trigger for the specified
> + pins
> +- drive-strength: Integer. Selects the drive strength for the specified
> + pins in mA.
> + Valid values are:
> + <2>
> + <4>
> + <8>
> + <12>
> +
> +Example:
> +
> + pinctrl: pinctrl@e01b0000 {
> + compatible = "actions,s700-pinctrl";
> + reg = <0x0 0xe01b0000 0x0 0x1000>;
> + clocks = <&cmu CLK_GPIO>;
> + gpio-controller;
> + gpio-ranges = <&pinctrl 0 0 136>;
> + #gpio-cells = <2>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,

Nitpick: Cells should be terminated with a semicolon. This was mentioned
in my previous review as well.

Regards,
Mani

> +
> + uart3-default: uart3-default {
> + pinmux {
> + groups = "uart3_rtsb_mfp", "uart3_ctsb_mfp";
> + function = "uart3";
> + };
> + pinconf {
> + groups = "uart3_all_drv";
> + drive-strength = <2>;
> + };
> + };
> + };
> --
> 2.17.2
>

\
 
 \ /
  Last update: 2018-11-15 11:56    [W:0.095 / U:9.592 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site