lkml.org 
[lkml]   [2018]   [Nov]   [15]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v2 09/15] Bluetooth: hci_bcm: Add support for regulator supplies
Date
The Broadcom Bluetooth chips have two power inputs, VBAT and VDDIO.
The former provides overall power for the chip, while the latter powers
the I/O pins and buffers.

Model these two as regulator supplies, and let the driver manage them
in the same way as it does the clock supply.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
---
drivers/bluetooth/hci_bcm.c | 39 ++++++++++++++++++++++++++++---------
1 file changed, 30 insertions(+), 9 deletions(-)

diff --git a/drivers/bluetooth/hci_bcm.c b/drivers/bluetooth/hci_bcm.c
index 345d728a5434..f2101038284e 100644
--- a/drivers/bluetooth/hci_bcm.c
+++ b/drivers/bluetooth/hci_bcm.c
@@ -31,6 +31,7 @@
#include <linux/property.h>
#include <linux/platform_data/x86/apple.h>
#include <linux/platform_device.h>
+#include <linux/regulator/consumer.h>
#include <linux/clk.h>
#include <linux/gpio/consumer.h>
#include <linux/tty.h>
@@ -53,6 +54,8 @@

#define BCM_AUTOSUSPEND_DELAY 5000 /* default autosleep delay */

+#define BCM_NUM_SUPPLIES 2
+
/**
* struct bcm_device - device driver resources
* @serdev_hu: HCI UART controller struct
@@ -73,7 +76,8 @@
* @btpd: Apple ACPI method to drive BT_REG_ON pin low ("Bluetooth Power Down")
* @txco_clk: external reference frequency clock used by Bluetooth device
* @lpo_clk: external LPO clock used by Bluetooth device
- * @clk_enabled: whether clocks are prepared and enabled
+ * @supplies: VBAT and VDDIO supplies used by Bluetooth device
+ * @res_enabled: whether clocks and supplies are prepared and enabled
* @init_speed: default baudrate of Bluetooth device;
* the host UART is initially set to this baudrate so that
* it can configure the Bluetooth device for @oper_speed
@@ -105,7 +109,8 @@ struct bcm_device {

struct clk *txco_clk;
struct clk *lpo_clk;
- bool clk_enabled;
+ struct regulator_bulk_data supplies[BCM_NUM_SUPPLIES];
+ bool res_enabled;

u32 init_speed;
u32 oper_speed;
@@ -216,17 +221,21 @@ static int bcm_gpio_set_power(struct bcm_device *dev, bool powered)
{
int err;

- if (powered && !dev->clk_enabled) {
+ if (powered && !dev->res_enabled) {
+ err = regulator_bulk_enable(BCM_NUM_SUPPLIES, dev->supplies);
+ if (err)
+ return err;
+
/* LPO clock needs to be 32.768 kHz */
err = clk_set_rate(dev->lpo_clk, 32768);
if (err) {
dev_err(dev->dev, "Could not set LPO clock rate\n");
- return err;
+ goto err_regulator_disable;
}

err = clk_prepare_enable(dev->lpo_clk);
if (err)
- return err;
+ goto err_regulator_disable;

err = clk_prepare_enable(dev->txco_clk);
if (err)
@@ -241,23 +250,27 @@ static int bcm_gpio_set_power(struct bcm_device *dev, bool powered)
if (err)
goto err_revert_shutdown;

- if (!powered && dev->clk_enabled) {
+ if (!powered && dev->res_enabled) {
clk_disable_unprepare(dev->txco_clk);
clk_disable_unprepare(dev->lpo_clk);
+ regulator_bulk_disable(BCM_NUM_SUPPLIES, dev->supplies);
}

- dev->clk_enabled = powered;
+ dev->res_enabled = powered;

return 0;

err_revert_shutdown:
dev->set_shutdown(dev, !powered);
err_txco_clk_disable:
- if (powered && !dev->clk_enabled)
+ if (powered && !dev->res_enabled)
clk_disable_unprepare(dev->txco_clk);
err_lpo_clk_disable:
- if (powered && !dev->clk_enabled)
+ if (powered && !dev->res_enabled)
clk_disable_unprepare(dev->lpo_clk);
+err_regulator_disable:
+ if (powered && !dev->res_enabled)
+ regulator_bulk_disable(BCM_NUM_SUPPLIES, dev->supplies);
return err;
}

@@ -936,6 +949,7 @@ static struct clk *bcm_get_txco(struct device *dev)
static int bcm_get_resources(struct bcm_device *dev)
{
const struct dmi_system_id *dmi_id;
+ int err;

dev->name = dev_name(dev->dev);

@@ -978,6 +992,13 @@ static int bcm_get_resources(struct bcm_device *dev)
dev->set_device_wakeup = bcm_gpio_set_device_wakeup;
dev->set_shutdown = bcm_gpio_set_shutdown;

+ dev->supplies[0].supply = "vbat";
+ dev->supplies[1].supply = "vddio";
+ err = devm_regulator_bulk_get(dev->dev, BCM_NUM_SUPPLIES,
+ dev->supplies);
+ if (err)
+ return err;
+
/* IRQ can be declared in ACPI table as Interrupt or GpioInt */
if (dev->irq <= 0) {
struct gpio_desc *gpio;
--
2.19.1
\
 
 \ /
  Last update: 2018-11-15 10:36    [W:0.146 / U:1.188 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site